TECKNET TK-WD895 Wireless Doorbells for Home User Manual
- May 15, 2024
- TECKNET
Table of Contents
Doorbell
Model: TK-WD895 / TK-WD896
User Manual
TK-WD895 Wireless Doorbells for Home
Thank you for purchasing TECKNET Doorbell. Please read this User Manual thoroughly before use of the product and retain it for future reference. If you have any problem using this product, please contact us by email at support@tecknetonline.com.
Package Contents
Product Overview
- Previous Chime/Mode Button
- Next Chime/Pairing Button
- Volume Button
- LED Light
- Push Button
- LED Light
- Screw Hole
Specifications
-
Receiver
Working Voltage: AC 100-240V, 50/60Hz
Power Consumption: 1 W -
Push Button
Working Voltage: DC 3V (CR2032 x1)
Working Current: 25mA
Transmission Power: 10 dBm
Install Push Button
Install with the Double-sided Tape
- Remove the battery isolation strip on the push button before use.
- Use the included double-sided tape to stick the push button to the wall.
Install with the Screws
To install you will need:
-
Remove the battery isolation strip.
-
Use a small standard screwdriver to detach the battery cover.
-
Screw mount the battery cover on the wall using the Phillips screwdriver. Snap the Push Button onto the battery cover.
Install Doorbell Receiver
Plug the doorbell receiver into an AC socket.
How to Use
- Switch Working Mode: Press and hold the “Previous Chime” button for 3 seconds to switch between 2 working modes: ringing only, ringing & flashing light.
- Select a Chime: Press the “Previous Chime” or “Next Chime” button once to select a chime. Stop pressing the button when you hear the chime you want.
- Select a Volume Level: Press the volume button to choose from 5 volume levels (mute, low, medium, high, and max).
Pair Push Button to Receiver
The Push Button and Receiver are already paired, so you can use them straight
out of the box. In case of any time you need to pair them, follow the steps
below:
- Press and hold the “Next Chime” button for over 3 seconds, and you’ll hear a “ding dong” prompt, showing that the receiver is in the pairing status.
- Press the Push Button, and the receiver plays the selected chime, which means the pairing operation is completed.
Tips:
One pairing operation can only connect one Push Button. One receiver can be
paired with up to 20 Push Buttons.
Clear Pairing Record
Press and hold the Volume Button for over 5 seconds, and you’ll hear a “ding
dong, ding dong” prompt, showing that the receiver has cleared all pairing
records. (This will remove all paired Push Buttons.)
Correct Disposal of This Product:
( Waste Electrical& Electronic Equipment )
This Marking shown on the product or its literature, indicate that it should
not be disposed with other household wastes at the end of its working life.
To prevent possible harm to the environment or human health from uncontrolled
waste disposal, please separate this from other types of wastes and recycle it
responsibly to promote the sustainable reuse of material resources.Household
user should contact either the retailer where they purchased this product, or
their local government office, for details of where and how they can take this
item for environmentally safe recycling.
Business users should contact their supplier and check the terms and
conditions of the purchase contact. This product should not be mixed with
other commercial wastes for disposal.
IMPORTANT SAFETY INSTRUCTIONS-CAREFULLY FOLLOW THESE INSTRUCTIONS.
- RETAIN THESE INSTRUCTIONS – This sheet contains important safety and operating instructions.
- Before using the product, read all instructions and caution markings on the product, accessories, and device.
- This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
- Children should be supervised to ensure that they do not play with the appliance.
- Keep the product away from the fire to avoid an explosion.
- For proper insertion, please observe polarity indicators (+/-).
- Do not place the product in or near an inflammable, explosive, or hazardous object.
- Do not operate the product if it has been damaged in any way.
- Do not disassemble the product. Disassembly may result in a risk of safety hazards.
- Do not throw or shake the product.
SIMPLIFIED EU DECLARATION OF CONFORMITY
Hereby, Shenzhen Unichain Technology Co., Ltd. declares that the product type
TK-WD895 / TK-WD896 is in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the
following internet address: https://teckneteu.com/
FCC STATEMENT:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
NOTE 2: Any changes or modifications to this unit not expressly approved
by the party responsible for compliance could void the user’s authority to
operate the equipment.
The device has been evaluated to meet general RF exposure requirement. The
device can be used in portable exposure condition without restriction.
Limited 12-Month Warranty
What this warranty covers.
Shenzhen Unichain Technology Co., LTD. (Manufacturer: “Unichain”) warrants to
the original purchaser of this TECKNET product that the product shall be free
of defects in design, assembly, material, or workmanship.
What the period of coverage is.
Unichain warrants the TECKNET product for 12 Months.
What will we do to correct problems?
Unichain will repair or replace, at its option, any defective product free of
charge (except for shipping charges for the product).
What is not covered by this warranty?
All above warranties are null and void if the TECKNET product is not provided
to Unichain for inspection upon Unichain’s request at the sole expense of the
purchaser, or if Unichain determines that the TECKNET product has been
improperly installed, altered in any way, or tampered with. The TECKNET
Product Warranty does not protect against acts of God such as flood,
earthquake, lightning, war, vandalism, theft, normal-use wear and tear,
erosion, depletion, obsolescence, abuse, damage due to low voltage
disturbances (e.g. brownouts or sags), non-authorized program, or system
equipment modification or alteration.
How to claim the warranty
Please contact retailers or visit TECKNET website or email
support@tecknetonline.com for more
information. To extend the warranty period, please visit TECKNET website and
register your TECKNET products within 90 days of purchase.
Disclaimer
Every effort has been made to ensure that the information and procedures in
this guide are accurate and complete, no liability can be accepted for any
errors or omissions and we reserve the right to make any changes without
further notice to any products mentioned herein.
IC Caution:
This device complies with Industry Canada s licence-exempt RSSs. Operation is
subject to the following two conditions:
- This device may not cause interference; and
- This device must accept any interference, including interference that may cause undesired operation of the device.
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>