TECKNET M006 2.4G USB Wireless Mouse User Manual
- June 6, 2024
- TECKNET
Table of Contents
TECKNET M006 2.4G USB Wireless Mouse
Package Contents
- 1x Cordless Mouse
- 1 x USB Nano Receiver
- 1x User Manual
Note : Batteries NOT incduded
System Requirements
To use this mouse, your computer must meet the following hardware requirements and run one of the operating systems listed below.
Hardware
- PC with a Pentium processor or equivalent AMD processors
- USB 2.0
Operating System
Windows XP, Vista, Win7, Win8, Win8.1, Win10
Note: The scroll wheel only works under the operating systems listed above. If you use the mouse under a different operating system, the mouse may either not work or lose its enhanced features.
Inserting the Batteries
The optical mouse uses two AA batteries (not included).
- Open the battery cover.
- Insert the batteries into the compartment, ensuring they correspond with the polarity markings.
- Close the battery cover
- Switch on the mouse by adjusting the power switch underneath the mouse. The Red LED of the power indicator at the top of the mouse wil fash.
Note : Make sure that the polarity of the batteries is correct. The positive () and negative (-) ends of each battery must match the positive (+) and negative (-) markings in the battery housing.
Product Layout
Technical Specifications
- Button Count: 6 buttons
- Operating Frequency: 2.4GHz
- Resolution: 800/1200/1600/2400/3200/4800DP1, Default 1200DPI
- Receiver Interface: USB version 2.0
- Battery Type 2 xAA Batteries
- Battery Life 30 months
- Operating Votage: 3.0V
- Operating Current: 5mA
- Stand by Current: <0,8mA
- Sleep Current: 0.05mA
- Sensor: P3212
- Transmission Power: 1.5dBm
30-Month Battery Life The mouse consumes little power and offers a long
battery life of up to 30 months without changing batteries. However please
note that the actual battery life may vary based on user and computing
conditions.
Receiver Connection Take out the USB Nano receiver and plug it into a
free USB port on your computer. The Plug &Play function of your system wil
detect that a new device has been connected and install it automatically.
Note : The receiver can be removed and stored in the battery compartment while not in use.
Intelligent Power Saving (IPS)
The mouse is equipped with Intelligent Power Saving (IPS) function. When the USB Nano receiver is disconnected or the PC is switched off, the mouse will be switched off automatically for the purpose of power-saving. When your mouse is not operated for 10 seconds, it will automatically drop to the first level of IPS. To wake the mouse, click any button. When your mouse is not operated for 8 minutes, it will automatically drop to the second level of IPS. To wake the mouse, dick any button.
DPI Switch
The mouse supports six levels of DPl: 800/1200/1600/2400/3200/4800DPL. The default DPl is 1200. Press the DPI button, DPI will raise to 1600, LED indicator will fash three times. Press the DPI button for each time, the DPl will raise to the next level, and the DPI LED light will Mash one more time.
The parameter is incorrect.Image size is not supported. Each image dimension must be between 40 and 2600 pixels.
Low Battery Power Indicator
The mouse is equipped with a low power indicator. When the battery power gets
low during the period of use, the Indicator under the scroll wheel will fash.
Please replace the batteries.
Note : We recommend you use AA alkaline dry cel batteries.
FAQ
What should I do if the mouse does not work? Make sure that the polarity of the batteries is correct. The positive (+) and negative (-) ends of each battery must match the positive (+) and negative (-) markings in the battery housing. Make sure the batteries are not discharged Please try to remove the batteries, and reinstall the batteries again. Verity that your computer’s power management features are turned off. Check the Nano receiver’s USB connector is firmly attached to the USB port of your computer. The USB Nano receiver is recognized by Windows (2000, 2003, XP, Vista, Win7, Win8, Win8.1, Win 10) but the cursor does not move? Check whether the low power indicator on the top of the mouse lights up. If the sensor lights up, it is likely that the batteries are discharged, Please replace them If replacing the batteries does not help, it is likely that the mouse is not connected to the receiver. Please try reconnection and ensure that the mouse is within the optimal operational working distance (1.5m) from its USB Nano receiver.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>