Sprout MakerWall Slotboard Installation Guide
- May 15, 2024
- Sprout
Table of Contents
Sprout MakerWall Slotboard
Adult installation only 2 Adults recommended for installation Install completely before use
PARTS
-
Slotboard (s) with attached vertical battens
-
3.5in Construction Screws
-
Black Screws
-
Horizontal Battens various lengths possible. order will be shipped with longer battens if applicable to setup.
PROVIDED TOOLS
-
T25 Torx Driver for 3.5in Construction Screws
-
4mm Hex Driver for Black Screws
-
4mm Hex Key for Black Screws
-
3/16 Drill Bit Stud finding Aid
-
Pin Nail Stud finding Aid
-
Mini Level Installation Aid
HELPFUL TOOLS
(not included)
Stud finder for identifying location of wall studs to ensure secure mounting.
NEEDED TOOLS
-
Drill gun for installing construction & black screws.
-
Tape Measure for measuring & positioning
-
Pencil for marking
ASSEMBLY INSTRUCTIONS
Following the steps indicated, line up the slotboard(s) on the ground in front of the installation location to determine positioning of slotboard(s) on wall.
Find & Mark the locations of the studs between your Left & Right Boundaries using a Studfinder A.
If you don’t have a studfinder B , follow suggestions 1-4.
Make sure that there are 2 Studs for every horizontal batten that is at least 28” wide.
If more studs are available, we recommend putting a screw in each one.
If there is only 1 Stud, you will need to adjust the positioning of your slotboard so that they can be mounted to at least 2 Studs.
With the help of another adult, place the first slotboard up on the wall, and determine how high you want it to be (Height A).
Then mark that height directly above your center mark.
Set the slotboard aside, and prepare the highest batten, as shown.
Screw the batten into the studs, as shown.
Repeat Steps 5 & 6 with the lower battens.
Attach the battens to wall at Heights B & C per the table, measuring top to top.
Ensure they are lined up horizontally with the highest batten.
With the help of another adult, position the slotboard up against the wall.
With the top center hole on the slotboard positioned over the pilot hole on the highest batten, screw in a Black Screw.
Using the provided mini-level to ensure your slotboard is level, fasten the slotboard to the bottom batten using a black screw in the bottom-right corner.
Check positioning of the slotboard. If it is correct, then install remaining screws.
If it is wrong, remove bottom-right screw and try again with bottom-left hole.
If you are placing another slotboard adjacent to the existing one using new battens, align the new battens flush with the installed ones. Confirm that the new battens are both level and positioned at the same height as the initial battens before marking the wall. Shift the new battens 3/8” away from the edge of the installed slotboard, then proceed to install them by replicating Steps 6-7.
If you are placing another slotboard next to your existing slotboard using the same battens as already installed (battens are wider than the current installed slotboard), then skip to step 12.
With the help of another adult, position the next slotboard perfectly flush and aligned with its neighbor.
Install 1 Black Screw in top-center hole, and check alignment.
If alignment is off, then remove the 1 Black Screw and try again in a different hole.
After successfully installing the first Black Screw, install remaining black screws.
Congratulations!
You have successfully installed your MakerWall Slotboard!
Customer Support
Frustrated?
Need Help?
Talk to our customer service agent at: +1 (833) 530-0033
Or email us at:support@sprout-kids.com
Watch our installation video at:sprout-
kids.com/collections/makerwall
References
- Search and Found - Instantly - search.com
- MakerWall – Sprout
- Montessori Furniture for Playful Learning Environments – Sprout
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>