SEALEY LED16S.V2 Extra Slim Solar Floodlights with Wall Bracket Instruction Manual
- June 17, 2024
- SEALEY
Table of Contents
LED16S.V2 Extra Slim Solar
Floodlights with Wall Bracket
Instruction Manual
EXTRA SLIM SOLAR FLOODLIGHTS WITH
WALL BRACKET
MODEL NO: LED16S.V2, LED20S, LED30S
LED16S.V2 Extra Slim Solar Floodlights with Wall Bracket
Thank you for purchasing a Sealey product. Manufactured to a high standard,
this product will, if used according to these instructions, and properly
maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE
OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND
WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY
CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP
THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to instructions
SAFETY
Maintain the light in good condition.
Ensure the light is installed correctly in accordance with these instructions.
Only install the light on a vertical surface.
DO NOT fix the light on any horizontal surface i.e. ceiling, or overhang.
Install away from flammable or combustible materials.
DO NOT direct the light into a persons eyes.
DO NOT install the light where it is likely to be knocked or hit.
DO NOT install in bathrooms, shower rooms, sauna or such locations.
DO NOT install near an exhaust outlet. e.g. Boiler flue, dryer outlet etc,
or mirrored surfaces.
DO NOT put the light in an area that is well lit at night, e.g., near a
street light. This may stop the sensor from determining when it is night time
and will stop the light from operating.
The light must be securely fixed to the mounting surface. The screws and wall
plugs supplied are suitable for masonry only.
Mount the light level and horizontal to the ground.
Turn the light off if it is not to be used for long periods.
Locate the light away from obstructions that block the light from reaching the
solar panel such as overhanging tree branches, fences or buildings.
INTRODUCTION
Extra-Slim Solar floodlights with Wall Bracket. Features both daylight (CDS)
and motion (PIR) sensors to switch on automatically.
Motion sensors can detect up to 6 metres. 30 second timer upon sensing motion.
All year-round solar charging regardless of cloud cover.
SPECIFICATION
Model No: …………………………………………… LED16S.V2
Battery: ………………………………………………….. 3.7V 3Ah
IP Rating: ……………………………………………………….IP54
LED Type: …………………………………………………….. SMD
Lumen Output: …………………………………………… 1600lm
Operating Time: .10 hours, once motion sensor activated
PIR Motion Sensor: ………………………………………….. Yes
Power: ……………………………………………………………16W
Model No ………………………………………………….LED30S
Battery: ……………………………………………2 x 3.7V 2.6Ah
IP Rating: ……………………………………………………….IP54
LED Type: …………………………………………………….. SMD
Lumen Output: …………………………………………… 3000lm
Operating Time: .10 hours, once motion sensor activated
PIR Motion Sensor: ………………………………………….. Yes
Power: ……………………………………………………………30W
Model No:……………………………………………LED20S
Battery: …………………………………………………………. 3.7V 3Ah
IP Rating: ………………………………………………………..IP54
LED Type: ……………………………………………………… SMD
Lumen Output: ……………………………………………… 2000lm
Operating Time: ……. 10 Hours once motion sensor activated
PIR Motion Sensor: …………………………………………………. Yes
Power: …………………………………………………………………..20W
ASSEMBLY
4.1. Unpack the product and check contents. Should there be any damaged or
missing parts contact your supplier immediately.
4.2. Also includes fixing kit.
4.3. Give careful consideration to the position of unit to ensure you obtain
maximum benefit from the lighting range.
4.4. With care remove the wall bracket from the light assembly by unscrewing
the retaining thumb screws (fig 1).
4.5. Locate the thumb screws, solar panel and light in a secure location.
4.6. Place the wall bracket at your desired location and spot mark through the
slots onto the fixing surface (fig 2).
4.7. Secure wall bracket with appropriate fixings, wall plugs, to suit
mounting surface.
4.8. Reassemble the light assembly (fig 3).
‰ WARNING! If working at height take adequate safety precautions to
prevent injury from falling.
OPERATION
5.1. Adjust the solar panel upwards to maximise the amount of direct
sunlight collected (fig 4).
5.2. Rotate the light downwards to obtain maximum coverage (figs 4 & 5).
5.3. Push the power button to switch on the light (fig 6).
‰ WARNING! To avoid unwanted activation ensure that the light is not
positioned so it detects unwanted objects such as road traffic or people using
nearby footpaths.
5.4. Green light illumination indicates that the floodlight is
charging.
MAINTENANCE
6.1. Wipe clean with soft dry cloth.
DO NOT use solvents.
NOTE: The light is a fully sealed unit with no serviceable parts on the
LED16S, However the LED20S, LED30S (fig.7) have 18650 lithium batteries that
are charged from the solar panel. A single battery in the LED20S, and two in
the LED30S. Simply unscrew the battery cap (anticlockwise) and replace when
required. Assemble with positive side/sides of battery/ batteries facing
downwards. (tighten clockwise).
ENVIRONMENT PROTECTION
**** Recycle unwanted materials instead of disposing of them as waste. All
tools, accessories and packaging should be sorted, taken to a recycling centre
and disposed of in a manner which is compatible with the environment. When the
product becomes completely unserviceable and requires disposal, drain any
fluids (if applicable) into approved containers and dispose of the product and
fluids according to local regulations.
REGISTER YOUR PURCHASE HERE
https://qrco.de/bcy2E9
WEEE REGULATIONS
Dispose of this product at the end of its working life in compliance with the
EU Directive on Waste Electrical and Electronic Equipment (WEEE). When the
product is no longer required, it must be disposed of in an environmentally
protective way. Contact your local solid waste authority for recycling
information.
BATTERY REMOVAL
Under the Waste Batteries and Accumulators Regulations 2009, Jack Sealey Ltd
are required to inform potential purchasers of products containing batteries
(as defined within these regulations), that they are registered with Valpak’s
registered compliance scheme. Jack Sealey Ltd.’s Batteries Producer
Registration Number (BPRN) is BPRN00705.
Note: It is our policy to continually improve products and as such we
reserve the right to alter data, specifications and component parts without
prior notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is
required for any claim.
Sealey Group, Kempson Way, Suffolk Business Park,
Bury St Edmunds, Suffolk. IP32 7AR
01284 757500
sales@sealey.co.uk
****www.sealey.co.uk
© Jack Sealey Limited
Original Language Version
LED16S, LED20S, LED30S
Issue 2 (3,5) 18/08/23
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>