SEALEY SMS2101 Ø200MM Sharpener with Honing Wheel Instructions

SMS2101 Ø200MM Sharpener with Honing Wheel
Instruction Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.  USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE  AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

SAFETY

1.1. ELECTRICAL SAFETY
❑ WARNING! It is the responsibility of the owner and the operator to read, understand and comply with the following: You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs, sockets, and any other connectors for wear or damage.
You must ensure that the risk of electric shock is minimized by the installation of appropriate safety devices. A Residual Current Circuit Breaker (RCCB) should be incorporated into the main distribution board. You must also read and understand the following instructions concerning electrical safety.
✓ Ensure that cables are always protected against short circuits and overload.
✓ Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that none are loose.
✓ Ensure that the voltage marked on the appliance matches the power supply to be used and that the plug is fitted with the correct fuse – see fuse rating at right.
x DO NOT use worn or damaged cables, plugs, or connectors. Have any faulty items been repaired or replaced immediately by a competent electrician?
✓ It is recommended that this device is wired directly to a fused isolator switch. If, however, a plug is fitted, the following applies:
✓ Fit a new plug according to the following instructions (the UK only).
a) Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’.
b) Connect the BROWN live wire to the live terminal ‘L’.
c) Connect the BLUE neutral wire to the neutral terminal ‘N’.
d) After wiring, check that there are no bare wires, that all wires have been correctly connected, and that the cable restraint is tight.

1.2. GENERAL SAFETY
✓ Check that the dehumidifier is in sound condition and in good working order. Take immediate action to repair or replace damaged parts.
✓ Use recommended parts only. Unauthorized parts may be dangerous and will invalidate the warranty.
x DO NOT stand or place any object less than 10cm from the front or rear of the unit.
x DO NOT obstruct the air intakes or outlets of the dehumidifier.
x DO NOT place any object into the outlets – the unit has a fan running at high speed, contact with this will cause injury.
x DO NOT operate the dehumidifier when you are tired or under the influence of alcohol, drugs or intoxicating medication.
x DO NOT switch the dehumidifier off by disconnecting it from the mains. ALWAYS switch to the -OFF” position first.
x DO NOT remove the float lever from the water collection tank.
x DO NOT connect or disconnect the plug from the mains with wet hands.
✓ Always discard the water from the collection tank, DO NOT use it for any other purpose.
✓ Place the dehumidifier on a level and stable surface.
x DO NOT use the dehumidifier at ambient temperatures below 5°C.
x DO NOT use the dehumidifier outside. x DO NOT use means to accelerate the defrosting process or to clean, other than those recommended by the manufacturer.
✓ The appliance shall be stored in a room without continuously operating ignition sources (for example open flames, an operating gas appliance, or an operating electric heater. • DO NOT pierce or burn.
✓ Be aware that refrigerants may not contain an odor.
✓ When using continuous draining, make sure that the drain hose is positioned correctly.
✓ Ensure that heating appliances are not exposed to the flow of air from the dehumidifier.
✓ Before attempting to move the dehumidifier, empty the contents of the collection tank.
✓ Switch off and disconnect it from the mains before attempting any cleaning or other maintenance work.
✓ Ensure that the dehumidifier is correctly turned off when not in use, and stored in a safe, dry area, out of reach of children. This appliance can be used by children aged 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience or knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
❑ WARNING : If the power cord is damaged, it must be replaced by a professionally trained person.

NOTE: This appliance can be used by children aged 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

INTRODUCTION

Wet stone sharpening system with aluminium oxide particle stone and detachable water trough, suitable for HSS tools. Supplied with leather honing wheel, grinding jig and  angle guide.

SPECIFICATION

Model No: ………………………………………….. SMS2101
Motor Power: ……………………………………….180W
Electrical Supply ………………………………… 230V-50Hz
Wheel Diameter ……………………………….Ø200 x 40mm
Axle Diameter ………………………………….. Ø12mm
No load Speed ………………………………………95rpm
Grinding Stone ……………………………..Ø200 x 40mm
Leather Honing Wheel …………………..Ø200 x 30mm
Sharpening Wheel……………………….SMS2101.SW
Leather Honing Wheel …………………..SMS2101.HW

SEE FIG.1
A……………………………………………….Power Cable
B ……………………………………….. On/Off Switch
C …………………………….Detachable Water Trough
D ……………………………………. Wet Stone
E ………………………………… Cow Hide Honing Wheel
F……………………………………………Tool Rest/Clamp
G …………………………Adjustable Support for Tool Rest/Clamp
H …………………………………………. Lifting Handle

ASSEMBLY

WARNING! Before assembly check to ensure grinder is unplugged from mains. Position on a flat surface with sufficient illumination.
4.1. TOOL REST
4.1.1. Fit adjustable support for tool rest fig.1G by unscrewing knobs and sliding rods into guides clamp in required position.
4.1.2. Side tool rest clamp fig.1F onto support.

4.2. WATER RESERVOIR
4.2.1. Position water reservoir fig.1C by hooking on to main body of sharpener.
4.2.2. Ensure water reservoir is clear of rotating wheel.
4.2.3. It is recommended to install the sharpener by mounting on a fireproof bench. Use the mounting holes to secure to work surface.
NOTE:- the machine has no front or rear side so you can grind with or against the direction of wheel rotation. When positioning  please consider access to On/Off switch fig.1B. G

GRINDING WHEELS

5.1. MANDATORY SAFETY INSTRUCTIONS. (The following instructions must be observed together with those in Section 1).
▲DANGER! Use of a damaged wheel (stone) is dangerous and may cause damage and/or personal injury.
5.1.1. WARNING! Ensure grinder is unplugged from mains supply before attempting to change grinding wheel (stone). Only persons qualified under the “Abrasive Wheels  Regulations” and holding a current grinding wheel certificate are authorised to change and dress grinding wheels (stones).
5.1.2. Grinding wheels used with this machine must be of an adequate speed rating and suitable for the material to be ground.
5.1.3. Ensure the maximum speed specification of the wheel is higher than that indicated on the machine data plate.
5.1.4. Check that grinding wheels are secure and that wheels are not worn or damaged, that there are no fissures or cracks. If damaged replace immediately.
5.1.5. Ensure replacement wheel is not damaged in any way such as cracks, deformations or splinters etc. Also check the mounting flanges for deformation, burrs or chips.  Damaged flanges must not be used as they may produce high stresses in the wheel causing it to break.
DO NOT over tighten a wheel. Never tamper with a wheel in order to adapt it to a different size shaft.
5.1.6. Install a new wheel as in 5.2. Once mounted on the grinder test the wheel before use by facing the grinder in a safe direction (point it away from yourself, others and  vulnerable items) and run for a short time. Dress the wheel if necessary.

5.2. WHEEL CHANGING PROCEDURE
‰ WARNING! Unplug sharpener from the mains power supply before changing wheel.
5.2.1. Hold grinding wheel firmly – protect your hands with a cloth, or wear gloves.
5.2.2. Unscrew retaining nut fig.2.1.
Note: The nut has standard right-hand thread (undo anti-clockwise).and must be loosened by turning anticlockwise. It may be necessary to strike the wrench sharply in the  loosening direction, with a soft-faced hammer, to loosen the nut.
5.2.3. Remove grinding wheel washer in order shown in fig.2 Carefully inspect the new wheel before installing to ensure there are no fissures, chips, or cracks.
‰ WARNING! DO NOT USE A DAMAGED WHEEL.
5.2.4. Inspect the blotters – if they are damaged, replace them. The grinder must never be used without genuine wheel blotters.
5.2.5. Install the new wheel by reversing steps above.

5.2.6. Hold wheel steady and secure locking nut. DO NOT over-tighten as this may crack the wheel.
5.2.7. To remove hide honing wheel. Hold wheel firmly and unscrew retaining knob, remove washer, remove wheel by sliding off shaft and key.
5.2.8. To refit repeat above in reverse order.

OPERATION

PRE-USE INSPECTION
‰ WARNING! INSPECT THE SHARPENER BEFORE USE. ENSURE THE SHARPENER IS UNPLUGGED FROM THE MAINS POWER BEFORE  COMMENCING THE INSPECTION.
6.1.1. Check the tool rests are securely fixed and can not come in contact with the grinding wheel.
6.1.2. Turn the grinding wheel/honing wheel by hand and check for any damage. Check they do not touch the tool rests and are correctly aligned.
6.1.3. If any of the above checks fail, replace, repair, or adjust as necessary before starting the sharpener.

6.2. WHEEL USE
6.2.1. Fill water reservoir to point of “V” notch the stone will become saturated with water, refill water as required. DO NOT grind without water.
At the end of grinding process empty water from reservoir and clean out.

6.3. USING THE SHARPENER
6.3.1. Plug sharpener into the mains power supply.
6.3.2. Clamp the tool into the tool rest/clamp fig.3 / fig.4.
6.3.3. Measure the grinding bezel by using the notches on the edges of the angle measurer fig.5. Place Angle measurer on wheel as shown fig.6 to obtain correct sharpening  angle, adjustment can be made by adjusting tool rest support fig.1G.
6.3.4. Remove angle measurer from wheel, lift edge of tool from wheel, ensure nothing is in contact with wheel.
6.3.5. Start Wheel by using on/off switch fig.1 B.

6.4. DIRECTION OF GRINDING
6.4.1. It is recommended to work against the direction of the grinding stone if you require to remove large amounts of metal, and to grind with the direction of the wheel if  finer more accurate work is required. See fig.3 / fig.4 for mounting positions to achieve this.
6.4.2. When using the honing wheel never sharpen against the direction of the wheel, as the tool will cut into the leather.

6.5. PREPARATION OF LEATHER HONING WHEEL
6.5.1. Before starting to use the honing wheel impregnate the leather with thin machine oil, then apply abrasive paste, turn on the wheel and spread the paste. This process  will need to be done after about five to ten sharpenings or as required and will increase the life of the leather.

MAINTENANCE

‰ WARNING! Ensure the grinder is unplugged from the mains power supply before performing any maintenance or service.
7.1. The machine motor and bearings are sealed units and require no regular maintenance. Should you require assistance, contact your local service agent.

ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a  manner which is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved  containers and dispose of the product and fluids according to local regulations.
WEEE REGULATIONS
Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment (WEEE). When the product is no  longer required, it must be disposed of in an environmentally protective way. Contact your local solid waste authority for recycling information.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.

Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500
01284 703534
****sales@sealey.co.uk
www.sealey.co.uk

References

• Sealey - Leading Professional Tool & Workshop Equipment Supplier

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>