SEALEY LED180 4W and 1W SMD LED Rechargeable Slim Inspection Light Instructions

SEALEY LED180 4W and 1W SMD LED Rechargeable Slim Inspection Light

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble-free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

• Refer to instructions

SAFETY

GENERAL

• It is important to ensure that the light is fully charged before initial use.

• DO NOT turn the light on when it is being charged.

• DO NOT shine directly into your, another person’s or an animal’s eyes.

• DO NOT allow children to use the light.

• DO NOT leave battery in a discharged state. Recharge battery immediately.
  Recharge the battery at least once every six months of non-use.

• There are no user serviceable components. DO NOT dismantle.

• DO NOT pull the charger plug from the mains socket by the lead.

BATTERY SAFETY

• WARNING! To reduce the risk of burns or fire:
• DO NOT Attempt to open, disassemble, modify or service the battery pack.
• DO NOT Crush, puncture, short external contacts or dispose of in fire or water.
• DO NOT Expose to temperatures above 40°C (104°F).
• Recycle or dispose of used battery as stipulated by local regulation.
• If the electrolyte in the cells gets on your skin, thoroughly wash with soap and water. If it gets in your eyes, rinse thoroughly with cool water and seek immediate medical attention

INTRODUCTION

Slimline foldout inspection light for use in confined spaces, with 6mm minimum thickness. Inspection arm can be rotated 180° and folded back for use as a hands-free inspection light. Features 4W SMD LEDs which produce up to 400 lumens, operated by a rolling dimmer switch, and a 1W SMD LED in the end for use as a directional torch. Suitable for hands-free operation with three magnets and a hanging hook. Folds away, small and compact, suitable for keeping in your pocket. Powered by a 3.7V 2Ah rechargeable Lithium-ion battery which lasts up to 8 hours. Supplied with USB charging lead.

SPECIFICATION

• Model No: …………………………………………………. LED180
• Battery: …………………………………..3.7V 2Ah Lithium-ion
• Charging time: …………………………………………………..3hr
• IP Rating: ……………………………………………………….IP20
• LED Type: ………………………………..4W SMD + 1W SMD
• Lumen output: ……………………….Side; 400lm, Top; 70lm
• Maximum length: ………………………………………… 300mm
• Minimum length: …………………………………………. 155mm
• Operating time: ………………..Side; 3hr (400lm), Top; 8hr

CHARGING

• The battery fitted to this light is considered to be a consumable item and its ability to accept charge will reduce over time. We will warranty it against mechanical and electrical defects for a period of one year, this does not cover fair wear and tear. If the battery is not properly charged before first use, or regularly conditioned, its capacity will diminish. Under these circumstances, we will not replace the battery even if it is less than one year old.
• Connect the charger into the charge socket on the light, see fig.1. Plug into power supply and turn on, the red charge LED on the light will light as the battery charges. When fully charged the LED turns green.
• When the battery has fully charged (approx 3hrs) Disconnect from mains supply.
  Note: The Lithium battery does not suffer from memory effect and once fully charged may be stored for up to six months without another charge.

OPERATION

Refer to fig.1

• Unfold light. Select either directional torch or inspection light. Brightness is controlled by dimmer switch.
• Light can be hung from the hook or attached using magnets.

MAINTENANCE

• Keep light clean and check for damage before every use. If damage is observed, remove from use until unit is repaired.
• The battery is not designed to be removed.

ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling center and disposed of in a manner that is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations.

BATTERY REMOVAL
Under the Waste Batteries and Accumulators Regulations 2009, Jack Sealey Ltd are required to inform potential purchasers of products containing batteries (as defined within these regulations), that they are registered with Valpak’s registered compliance scheme. Jack Sealey Ltd’s Batteries Producer Registration Number (BPRN) is BPRN00705.

WEEE REGULATIONS
Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment (WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid waste authority for recycling information.

Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: The guarantee is 12 months from the purchase date, proof of which is required for any claim.

Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR

01284 757500
01284 703534
sales@sealey.co.uk
www.sealey.co.uk

References

• Sealey - Leading Professional Tool & Workshop Equipment Supplier

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>