HS-SW531 Set Wireless Pro Controller Instruction Manual
- June 12, 2024
- HS-SW531
Table of Contents
PLAYCOOL PRO
CONTROLLER
Compatible for N-Switch / N-Switch Lite /
N-Switch OLED / PC HS-SW531
Instructions Instructions
HS-SW531 Set Wireless Pro Controller
Component Names and Functions / Name en functions van onderdelen
1 Screenshot Button
2 L Button
3 TURBO Button
4 L3 Button of Left Stick
5 – Button
6 + Control Pad
7 ZR Button
8 M1, M2 Button
9 Mode Switch
10 Indicator light| 11 R Button
12 + Button
13 A,B,X,Y Button
14 R3 button of Right Stick
15 RGB LED
16 HOME Button
17 ZL Button
18 M3,M4 Button
19 USB Type-C connector
---|---
Product Brief
This is a Bluetooth wireless controller which is used together with Nintendo Switch console. The console can be awakened with one key. It supports motor vibration and adjustment, manual turbo, automatic turbo and turbo speed adjustment. It can also be used on PC, on Android platforms (realize Android Gamepad mode) and on iOS 13 (MFI games).
Operation Guide
-
Descriptions of Modes and Connection
Nintendo Switch mode connection:
Long press Home button for 3 to 5 seconds and the LED will flash quickly to enter the Bluetooth search mode. After it is successfully connected, corresponding channel indicators will be always on.
Note: After the controller enters the synchronous mode, it will sleep automatically if it is not synchronized successfully within 2.5 minutes. -
Enter the controller setting page according to the following orders.
-
Enter the page to switch the controller mode.
-
0pen the controller according to instructions of (initial use) and enter the connection state. It will be normally operated after successful connection.
Connection of Android Gamepad Mode:
Long press HOME+X for 3 to 5 seconds and the LED will flash quickly to enter
the Bluetooth search mode. After it is successfully connected, LED1 will be
always on.
iOS 13 mode connection:
Long press HOME+A for 3 to 5 seconds and LED2+LED3 will flash quickly; after it
is successfully connected, LED2+LED3 will be always on. It can also be used to
play MFI game.
Connection of PC Bluetooth Mode:
PC Bluetooth mode connection: Long press HOME+X for 3 to 5 seconds and the
LED1 will flash quickly to enter the Bluetooth search mode. After it is
successfully connected, LED1 will be always on.
(Note: Android mode is used when it is connected with the computer through
Bluetooth. Only experienced players who can set values of buttons are
recommended to use it.)
Reconnect and Wake-Up
Reconnect: When the controller is in sleep state, short press any
button(A.B.X.Y.+.- .O.↑/↓/←/→) and the LED1-LED4 flash. Now the controller will
automatically connect back to the console.
Wake-Up: When the controller is in sleep state, short press the home button
and the LED1-LED4 flash. Now you wake up the console and the controller will
automatically connect back to the console
Dormant State and Disconnection
If the console screen is off, the controller will automatically enter the
dormant state.
If no button is pressed within 5 minutes, the controller will enter the
dormant state automatically (the sensor does not work). In the wireless
connection state, you can press HOME Button for 5 seconds to disconnect it
from the console.
Charging Indication
During the shutdown state, if the controller is charged, LED1-LED4 will flash
slowly; if it is fully charged, LED light will be off;
During the connection state, if the controller is charged, the current channel
indicator will flash (slow flashing). The current channel indicator will be
always on when the controller is fully charged;
Low Voltage Alarm
If the battery voltage is lower than 3.55V0.1V, the current channel light
will flash quickly to show the low voltage. When the battery voltage is lower
than 3.45V±0.IV, the controller will enter the dormant state automatically.
Low voltage alarm: The current channel indicator flashes (fast flash).
TURBO Function
A: Manual Turbo Setting: (First Time) Press one or several buttons
(A/13/X/Y/L/R/ZL/ZR) and then press TURBO button to start the manual TURBO
function.
B: Automatic Turbo Setting: (Second Time) Press the button with manual Turbo
function again and then press “TURBO” button to start the automatic TURBO
function.
C: Clear TURBOSetting: (Third Time) Press the button with automatic TURBO
function again and then press “TURBO” button to clear the TURBO function.
D. Clear All TURBO: First press and hold the TURBO button for more than 3
seconds and then press the “-” button to clear the TURBO function of all
buttons.
Wired Connection
PC Connection: Please use a USB cable to connect the controller and the
computer. The controller LEN will be always on after connection.
(Note: The default mode of the controller on PC is X-INPUT mode)
Nintendo Switch Connection: Please use a USB cable to connect the controller
and the SWITCH console. After connection, corresponding LED lights on the
controller will be always on.
RGB Dazzling Light
When the controller is turned on, the dazzling light will be set by default
and the 8 colors of blue, red, green, yellow, green, orange, purple and pink
will be set circularly. Continuously press T Button for 3 times to turn off
the dazzling light and then press T Button for 3 times to turn on the dazzling
light.
Motor Vibration Speed Adjustment (for Nintendo Switch Only)
When the controller is well connected, press L, R, ZL and ZR buttons
simultaneously to adjust the motor intensity (the controller will vibrate once
each time you adjust it); The motor vibration can be divided into three levels
of “throng” “edium”anCeak” Each time it is used, the “edium”level is the
default level, followed by “trong’and “each” The rest can be done in the same
manner.
M Button Function Programming
M button= M 1.M2.M3.M4; buttons that can be programmed include
↑/↓/←/→/A/B/X/Y/L/R/ZWZR/L3/R3;
Close M Button Function Turn the Mode Switch to the middle to close M Button
function.
Normal Mode
Shift the Mode Switch to the right of (M2 direction), M1 for X, M2 for Y, M3
for B, M4 for A. (Note: It cannot be programmed in normal mode)
Programming Mode
-
Shift the Mode Switch to the left of (M3 direction). M1 for ZR, M2 for R, M3 for L, and M4 for ZL.
-
Setting Method: Press M Button; then, press ”+” Button and the indicating light will flash.
Then, release it to enter programming. Then, press any one or several buttons to be set (↑/↓/←/→/A/B/X/Y/L/R/ZL/ZR/L3/R3) and M button to save the setting. -
Press M1 Button, M4 button and- button at the same time for three second and the Indicator will flash once to restore the default value.
For example, press M1 Button and press ”+” Button to set the programming (the
Indicator flashes once). Press A button and M1 button to save the setting. At this point, M1 Button corresponds to A button function.
Note: When entering the program, if you do not press the button which can set the programming, the originally set functions will be cleared.
Reset Controller Hardware
In case of abnormal situations of the controller, please long press HOME
button for more than 10 seconds to reset the controller hardware.
Controller Upgrading
-
Double click the update software to open the interface.
-
During the shutdown state, press the left joystick (L3) and connect the controller to the computer through the USB type-C interface cable.
-
After successful connection, release the left joystick (L3) and lay the controller flat. At this time, the software window button ”Update Firmware” will change from gray to an operational one.
Click ”Update Firmware” on the upgrade interface and the controller will be upgraded automatically. After the completion of the upgrade, LED1 and LED4 of the controller will flash and the upgrading process will be finished. -
Open the controller according to instructions of (initial use) and enter the connection state. It will be normally operated after successful connection.
The way to upgrade APP
- Support Key Linker APP for air upgrade ( APP can be downloaded through the official website or QR code)
- APP can modify buttons, adjust joystick sensitivity, Turbo speed adjustment, motor vibration adjustment , macro programming , etc
- This QR code is available for both general Android and IOS systems
http://gpcloud.smart-one.cn/keylinker/
You can search for ” Key linker ” on Pasture , Google play , 360App Store , Dandelion , Xiaomi App Store , Huawei App Store OPPO App Store , Tencent App Store and other platforms to download , or scan the above QR code to download
Electrical Parameters
Dormant Current: Less than 27uA
Pairing Current: 30~60mA
Working Voltage: 3.7V
Current: 25mA-150mA| Input Voltage: DC4.5~5.5V
Input Current: 1000MAH
Bluetooth Version: 2.1+EDR
---|---
Notes
- Please do not store product in humid or high temperature places.
- Do not knock, beat, puncture, or try to disassemble. Avoid unnecessary damage to the product.
- The product will not be covered by after-sales warranty if the product has been disassembled by non-professionals.
- If some games cannot be played because of official game platform software upgrades or source code changes we are not responsible.
Service and Warranty:
If you need service or information regarding your product, please contact us
at contact@elite-store.nl
Play Cool provides a 1 year warranty on its products. The products needs to be
returned with a proof of purchase and the defects need to be reported within
one year from the date of purchase.
This warranty does not cover:
- Damages caused by misuse or incorrect repair;
- Damages by wearable goods;
- Defects that the customer was aware of at the time of purchase;
- Damages or defects caused by costumer neglect;
- Damages or defects caused by third parties.
PLAYCOOL PRO
CONTROLLER
Documents / Resources
| HS-
SW531 HS-SW531 Set Wireless Pro
Controller
[pdf] Instruction Manual
HS-SW531 Set Wireless Pro Controller, HS-SW531, Set Wireless Pro Controller,
Wireless Pro Controller, Pro Controller, Controller
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>