RAB WPX Field Adjustable Wall Pack Instruction Manual

RAB WPX Field Adjustable Wall Pack

Product Information

Specifications:

• Model: WPXTM Field-Adjustable Wall Pack
• Power Options: 30/20/15W, 80/60/40W, 130/100/65W

Product Usage Instructions

Important Safety Information:
Before proceeding with the installation, please read and understand the following safety precautions:

• Ensure power is OFF before installing or maintaining the fixture.
• Proper grounding is required for safety.
• All gaskets must be seated properly, screws inserted and tightened firmly.
• Apply weatherproof silicone sealant between mounting surface and back housing.

Mounting the Fixture to Surface:

1. Ensure the fixture is not recessed. Mount the fixture to the surface with the lens facing down.
2. Use the provided Drill Template on the inside Back Housing surface or utilize Lag Bolt Locations to mount the fixture securely.
3. Open the fixture door and remove the reflector to prepare the housing for mounting.
4. Drill out the appropriate mounting hole pattern inside the Back Housing.
5. Line up the housing in the desired location and mount securely.

Electrical Connections:

1. Make electrical connections as shown in the wiring diagram. Use approved wiring connectors and follow local NEC codes.
2. Be careful not to pinch the wires during installation.

Field Adjustment – Photocell Operation:
This product comes with a photocell that is set to the OFF position by default. To enable the Photocell ON feature, slide the center switch to the ON position. If the Photocell is set to ON and it is daylight, it may take up to 60 seconds for the light to turn off.

Frequently Asked Questions (FAQ):

• Q: How do I adjust the power settings of the WPXTM Field-Adjustable Wall Pack?
  A: The power settings can be adjusted based on the wattage options provided (30/20/15W, 80/60/40W, 130/100/65W). Please refer to the user manual for detailed instructions on adjusting the power settings.

• Q: What should I do if I encounter issues with the Photocell operation?
  A: If you experience any problems with the photocell operation, ensure that it is set to the correct position as per the instructions. If issues persist, contact RAB Lighting’s customer support for assistance.

IMPORTANT

READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE. RAB fixtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper grounding is required for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
WARNING: Make certain power is OFF before installing or maintaining fixture. No user serviceable parts inside.
CAUTION: For proper weatherproof function all gaskets must be seated properly and all screws inserted and tightened firmly. Apply weatherproof silicone sealant between mounting surface and back housing. This is especially important with an uneven wall surface. Silicone all plugs and unused conduit entries.

MOUNTING FIXTURE TO SURFACE

1. Fixture should not be recessed. Mount Fixture to surface with Lens facing down as shown in Fig. 1.
2. Use the Drill Template on the inside Back Housing surface to match most standard junction boxes or utilize Lag Bolt Locations (4) as shown in Fig. 2 to mount the fixture to surface.
3. Open fixture Door by loosening Screws (2) and remove Reflector by loosening Screws (2). Reflector will hang by preinstalled Tether Cable as shown in Fig. 3.
4. Prepare the housing for use by drilling out the appropriate desired mounting hole pattern inside of the Back Housing (Fig. 1).
5. Line up the housing in the desired location and mount securely.
6. Make electrical connections as show in wiring diagram (Fig. 7). Use approved wiring connectors and appropriate wiring method and wire to local NEC codes. Be careful not to pinch the wires
7. Re-install the Reflector and secure with Screws (2) back into it’s original position as shown in Fig. 4 and re-install the fixture Door, secure with (2) Screws.

FIELD ADJUSTMENT

Photocell Operation:
This product is equipped with a photocell. Photocell factory setting is set to the “OFF” position. Should you wish to enable the Photocell “ON” feature slide the center switch to the “ON” position (Fig 6). If the Photocell is set to the “ON” position and it is daylight it may take up to 60-seconds for the light to turn off.

Color Temperature (CCT) Selection:
This product is equipped with 5000K, 4000K or 3000K CCT Color Temperature selection. For maximum light output use the 4000K Color Temperature (CCT).

Power (%) Selection:
This product is equipped with 50%, 75% and 100% power output selection.

Follow instructions to change Photocell ON/OFF operation, Color Temperature (CCT) and/or Power (%) from factory settings by removing Clear Threaded Plug (Fig. 5) on side of housing.
Factory Settings: 100% Power, 4000K CCT, Photocell/ OFF

1. Locate the Selector Switches on side of housing as shown in Fig. 6.
2. Select Color Temperature (CCT), Power (%) and/or Photocell ON/OFF function by sliding the respective switch to the desired value (Fig. 6). Replace the Clear Threaded Plug.

MVS MODELS (Internal)
(optional remote sold separately for custom settings, CAT# MSR1).

• Factory Settings:
  • Brightness: 100%
  • Hold Time: 20 Minutes
  • Daylight: Disabled
  • Sensitivity: 100%
  • Stand-by dimming level: 20%
  • Stand-by time: 1 Minute

0-10V DIMMABLE WIRING

Universal voltage driver permits operation at 120V through 277V, 50 or 60 Hz. Units ordered with /480 suffix are 480V, 60Hz ONLY. For 0-10V dimming follow the wiring directions as shown in Fig. 7.

1. Connect the black fixture lead to the LINE supply lead.
2. Connect the white fixture lead to the COMMON supply lead.
3. Connect the GROUND wire from fixture to supply ground.
4. Connect the purple fixture lead to the (V+) DIM lead.
5. Connect the pink fixture lead to the (V-) DIM lead.
6. Cap the yellow fixture lead if present. Do NOT connect.

NOTE: Do not connect DIM V+ (purple)/ DIM V- (pink) to line voltage or supply ground.

TROUBLESHOOTING

1. Check that the line voltage at the fixture is correct. Refer to wiring directions.
2. Is the fixture grounded properly?
3. Be sure the photocell, if used, is functioning properly.

CLEANING & MAINTENANCE

CAUTION: Be sure fixture temperature is cool enough to touch. Do not clean or maintain while fixture is energized.

1. Clean lens with non-abrasive glass cleaning solution.
2. Do not open the fixture to clean the LED. Do not touch the LED.

Note: These instructions do not cover all details or variations in equipment nor do they Fig: 7 provide for every possible situation during installation, operation or maintenance.

BATTERY BACKUP MODELS

WIRING

CAUTION: FOR BATTERY BACKUP FIXTURE. Voltage can be present in BATTERY. To prevent high voltage from being present on output leads, Inverter connector must be open. Do not join BATTERY connector until installation is complete.
NOTE: Make sure that the necessary branch circuit wiring is available. An UNSWITCHED AC source of power is required. The emergency driver must be fed from the same branch circuit as the LED driver. Reference Fig. 8 for wiring diagram.

CAUTION: Do not use any supply voltage other than 120-277V, 50/60Hz.

1. Connect UNSWITCHED HOT fixture lead to HOT AC supply line.
2. If using an UNSWITCHED circuit, connect UNSWITCHED and SWITCHED lines together.
3. If using a SWITCHED circuit, connect SWITCHED HOT lead to the switch.
4. For 0-10V dimming, connect DIM (+) purple and DIM (-) pink leads to 0-10V dimming connection.
5. All unused leads must be capped and insulated.
6. After installation is complete connect the battery as shown in Fig. 8.
7. When power is on, the fixture should be on and the CHARGING INDICATOR LIGHT should illuminate to indicate the battery is charging.
8. Once the BATTERY has charged for at least one hour, a short-duration test may be performed by pressing the Test Button as shown in Fig. 9.
9. After the battery has charged for 24 hours, a long-duration test can be performed by disconnecting power to the fixture.

OPERATION

1. When AC power is applied the charging indicator light is illuminated indicating that the BATTERY is being charged.
2. When power fails the standby power automatically switches to emergency power (internal battery) operating at reduced illumination.
3. When AC power is restored the emergency driver automatically returns to charging mode.

MAINTENANCE
Although no routine maintenance is required to keep the emergency driver functional, it should be checked periodically to ensure that it is working. The following schedule is recommended:

1. Visually inspect the charging indicator light monthly. It should be illuminated
2. Test the emergency operation of the fixture at 30-day intervals for a minimum of 30 seconds.
3. Conduct a 90-minute discharge test once a year. Fixture would operate at reduced illumination for a minimum of 90 minutes.

TROUBLESHOOTING

1. Be sure the fixture is grounded properly.
2. If the charging indicator light does not illuminate after pressing and releasing the Test Button (Fig. 9), check power and check if battery is connected properly.

rablighting.com
Visit our website for product info
Tech Help Line
Call our experts: 888 722-1000
e-mail
Answered promptly – sales@rablighting.com
Free Lighting Layouts
Answered online or by request

RAB WARRANTY: RAB’s warranty is subject to all terms and conditions found at rablighting.com/warranty.

References

• Welcome to RAB
• Legal - RAB Lighting

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>