AsReader ASR-020D-V2 Barcode Parameters for HID Mode Instructions
- June 13, 2024
- AsReader
Table of Contents
AsReader ASR-020D-V2 Barcode Parameters for HID Mode
Copyright © Asterisk Inc. All Rights Reserved.
AsReader ® is registered trademarks of Asterisk Inc.
The contents of this manual are subject to change without notice
Preface
This manual describes the parameters required for some settings when using AsReader ASR-020D-V2, ASR-020D-V3 and ASR-020D-V4 (hereinafter referred to as ASR-020D) in HID mode. For other settings, please refer to the dedicated barcode setting manual.
How to change the settings
Select the appropriate setting code from this manual and scan it. The new
settings will be saved in the ASR-020D.
Note: Make sure the ASR-020D’s battery is fully charged before setting.
If you have any comments or questions about this manual, please contact us:
Online, via https://asreader.com/contact/
Or by mail, at: Asterisk Inc., Shin-Osaka Dainichi Bldg. 201, 5-6-16
Nishinakajima, Yodogawa-ku, Osaka-city, Osaka, 532-0011 JAPAN
TEL: +81 (0) 50 5536 8733 in Japanese
TEL: +1 503-770-2777 x102 in
Japanese or English (U.S.A.)
TEL: +31 (0) 10 808 0488 in Japanese or English(E.U.)
Default Settings of ASR-020D
ASR-020D is shipped with the settings stated in the table below.
In this manual, the default parameter of each item is marked with an asterisk
| Item | Default | Page |
|---|---|---|
| Factory Default | – | P.3 |
| Vibration | Vibration On | P.3 |
| Sleep Mode | Sleep Mode On | P.4 |
| Beep After Scan | Beep After Scan On | P.5 |
| Battery Gauge LED | Battery Gauge LED On | P.6 |
| Power On Beep | Power On Beep On | P.7 |
| Aimer After Scan | Aimer After Scan On | P.8 |
| Inter-Character Delay | 10ms delay | P.9~P.10 |
Country Keyboard Layout
Type Code
| North American Standard
Keyboard
| P.10
- Factory Default
Scan the code below to restore the factory settings.
To execute Factory default successfully, it is recommended to scan “Factory Default” and turn off the barcode after 3 seconds. If the power of the barcode is turned off within 3 seconds, the factory default may not be fully executed.
Factory Default
@FCTDFT
- Vibration： “@VIBONX”
Scan the appropriate code below to set whether to vibrate when scanning a barcode.
| Vibration Off | Vibration On＊ |
|---|---|
| @VIBON0 | @VIBON1 |
| Current Value? | |
| --- | --- |
| @VIBON? |
- Sleep Mode: ”@SLMONX”
Scan the appropriate code below to set whether to apply sleep mode to ASR- 020D.Sleep Mode Off| Sleep Mode On＊
---|---
| 
@SLMON0| @SLMON1
Current Value?|
---|---
|
@SLMON?| - Beep After Scan: “@BASONX”
Scan the appropriate code below to set whether to beep when scanning a barcode.Beep After Scan Off| Beep After Scan On＊
---|---
|
@BASON0| @BASON1
Current Value?|
---|---
|
@BASON?| - Battery Gauge LED: “@BGLONX”
Scan the appropriate code below to enable or disable the battery gauge LED (Battery level indicator) on the back of ASR-020D.
| Battery Gauge LED Off | Battery Gauge LED On＊ |
|---|---|
| @BGLON0 | @BGLON1 |
| Current Value? | |
| --- | --- |
| @BGLON? |
- Power On Beep: “@POBONX”
Scan the appropriate code below to set whether to beep when ASR-020D is powered on.Power On Beep Off| Power On Beep On＊
---|---
|
@POBON0| @POBON1
Current Value?|
---|---
|
@POBON?| - Aimer After Scan: “@AASONX”
Scan the appropriate code below to set whether the aiming light keeps ON after scanning a barcode.Aimer After Scan Off| Aimer After Scan On＊
---|---
|
@AASON0| @AASON1
Current Value?|
---|---
|
@AASON?| - Inter-Character Delay: “@ICDSVX”
Scan the appropriate code below to set the display interval time between characters of the barcode data.5ms delay| 10ms delay＊
---|---
|
@ICDSV1| @ICDSV2
15ms delay| 20ms delay
---|---
|
@ICDSV3| @ICDSV4
25ms delay| 35ms delay
---|---
|
@ ICDSV5| @ICDSV7
50ms delay| Current Value?
---|---
|
@ICDSVA| @ICDSV? - Country Keyboard Layout Type Code: “@CKLTCX”
Scan the appropriate code below to set country keyboard layout of ASR- 020D.North American Standard Keyboard＊| German Keyboard(QWERZ)
---|---
|
@CKLTC0| @CKLTC1
Current Value?|
---|---
|
@CKLTC?|
Barcode Parameters for HID Mode
For ASR-020D-V2/ASR-020D-V3/ASR-020D-V4
Apr. 2023 5nd version Asterisk Inc.
Shin-Osaka Dainichi Bldg. 201, 5-6-16 Nishinakajima, Yodogawa-ku,
Osaka-city, Osaka, 532-0011 JAPAN
