TECHNI MOBILI RTA-B002 Sit to Stand Rolling Adjustable Height Laptop Cart with Storage Instruction Manual

June 17, 2024
TECHNI MOBILi

TECHNI MOBILI RTA-B002 Sit to Stand Rolling Adjustable Height Laptop Cart with Storage

ECHNI MOBILI RTA-B002 Sit to Stand Rolling Adjustable Height Laptop Cart
with Storage

MAIN PARTS LIST

  • 1 x1 Left panel


  • **2 x1 Right panel

**

  • **3L x2 Locking caster

**

  • **3N x2 Non-locking caster

**

  • **4 x1 Back pane

**

  • **5 x1 Front panel

**

  • **6 x1 Middle shelf

**

  • 7 x1 Bottom panel
    Main Parts List

  • 8 x1 Top shelf
    Main Parts List

  • **9 x2 Stationary tube

**

  • **10 x2 Adjustable “T” tube

**

  • **11A x2 Plastic square cover

**

  • **11B x2 Screw knob

**

  • 12 x1 Main panel
    Main Parts List

  • **13 x1 Top protection tube

**

MAIN PARTS LAYOUT (FOR REFERENCE):

Main Parts Layout \[For Reference\]:

Screws List And Included Tools


PART| QTY| ITEM|
A| 16| M4x14|
B| 2| M6x25|
C| 10| M6x35|
D| 22| M6x40 Bolt|

1

| Screwdriver|

BEFORE YOU START THE ASSEMBLY, PLEASE READ THE FOLLOWING TIPS AND

WARNINGS.

  • Please read the assembly instructions throughly and follow step by step.

  • Make sure you understand which hardware will be used on each step. Using the wrong size of screw, bolt or pin might strip the threads or cause damage to the part in which it is being used.
    Tools Required

  • To avoid misalignments, always leave the screws loosely and do not tighten them until all the pieces are positioned correctly.

  • Do not overtighten or force the screws as they might break, strip, damage the threads of the holes, or get stuck inside the parts.

  • If the hole seems to small for the screw, make sure you are using the correct size of screw and/or that you are installing it in the correct hole.
    Tools Required

  • Sometimes on the wood panels the laminate or material might be covering the hole partially or entirely, if there is no visible hole or if it looks too small, pass and press the tip of your finger over the area to feel its indentation, and carefully pierce the laminate to uncover the hole underneath.
    Tools Required

  • After the item is assembled, you can use rubbing alcohol to erase or remove the visible part numbers printed or labeled on the pieces.

THE ASSEMBLY STEPS START ON NEXT PAGE

**CAM BOLT AND CAM LOCK TUTORIAL THE INSTRUCTIONS BELOW ARE NOT ACTUAL ASSEMBLY STEPS

**

This unit uses cam bolts and locks (also known as mini fixes). If you are not familiar with this kind of hardware, the below is a tutorial that explains how to use them on the steps where they are required.

  1. Screw the bolt into the indicated hole on the panel indicated in the assembly step.

  2. Join the other panel (with the big hole) to the  panel with the bolt. If it comes with the cam locks already pre-installed, make sure to align them to receive the bolt’s head (refer to point 3). There might be a very small gap between the panels which is normal.

  3. Insert the cam lock on the panel with the big hole making sure it goes aligned to receive the bolt’s head.

  4. Use a Phillips screwdriver to turn the cam lock clockwise. This will lock the panels togheter and also will close any gaps.

ASSEMBLY STEPS

WE RECOMMEND TO PLACE THE PIECES OVER BLANKETS TO PROTECT THEIR FINISH DURING ASSEMBLY.

STEP 1

Hardware:

D|
D M6x40
Bolt| 5
Pcs

  • Attach bolts D into the indicated holes on the left panel 1.
  • On panels 4, 5 and 6 check and make sure the cam locks on their left side are aligned to receive the bolts.
  • Assemble the panels 4, 5 and 6 to panel 1 and turn the cam locks to lock the panels as explained in page 3. Note: Panels 4 and 6 do not assemble one another, they just lay flushed.
    Assembly Steps

STEP 2

Hardware:


D|

M6x40
Bolt

| 5
Pcs

Screw bolts D into the corresponding holes on the right panel 2, then align cam locks on panels 4, 5, 6 and finally assemble panel 2 to those panels and turn the cam locks as explained in page 3
Assembly Steps

STEP 3

Hardware:

A|
M4x14| 16
Pc

Use screws A to assemble the casters 3 to panel 7 to its bottom surface the following way:

  • Locking casters 3L go at the front of the panel.
  • Non-Locking casters 3N go at the back of the panel.
    Assembly Steps

STEP 4

Hardware:

D|

M6x40 Bolt

| 6
Pcs

Assemble the panels 1, 2 and 4 (from step 2) to the top surface of panel 7 with bolts D as explained in page 3. Please make sure to identify the correct holes where D will be installed on the bottom panel.
Assembly Steps

STEP 5

Hardware:

D|
M6x40
Bolt| 6
Pcs

Assemble the top shelf 8 to panels 1, 2 and 4 with bolts D as explained    in page 3.
Assembly Steps

STEP 6

Hardware:

C|
M6x35| 6
Pcs

Assemble the stationary tubes 9 to the side panels 1 and 2 with screws C from the sides and to the bottom panel 7 from the bottom.
Assembly Steps

STEP 7

Place the plastic covers 11A over the tubes 9 with their threaded holes facing towards the outside.

Assembly Steps

STEP 8

  • Insert the adjustable “T” tubes 10 through the covers 11A and into the tubes 9 making sure the longer end of the square tubes faces towards the front.
  • Lift the tubes at least 7 inches (about an open hands’ width) and insert and tighten the screw knobs 11B into the covers 11A.
  • Both tubes should be lifted at the same height to be able to do the next step properly.

FIRST:

**THEN:

**

STEP 9

Hardware:

C|
M6x35| 4 Pcs

Assemble the main panel 12 to the tubes 10 with screws C from underneath.
Assembly Steps

STEP 10

Hardware:

B|

M6x25

| 2 Pcs

Assemble the protection tube 13 to the main panel 12 with screws B from underneath.
Assembly Steps

STEP 11

LIFTING: Loosen the screw knobs 11B to lift, then tighten again.
Assembly Steps

  • If you have objects or devices on or under the main panel, use caution when adjusting the height.
  • Do not overtighten the screw knobs.
  • Do not use the unit if the plastic covers look cracked or if the screw knobs are stripped.

ROLLING : Unlock the front casters to allow free movement.
Assembly Steps

  • Before moving the unit, unlock the front casters and secure or remove any object that might fall off while the unit is rolling.

WEIGHT LIMITS

WARNINGS

  • Do not exceed the indicated weight limits.
  • Because the lift and lock system on this product consists of friction between metals, so frequent adjustments of the main top might cause scuffs on the metal tubes. This consequence is not considered a defect, and even with the scuffs, the unit should be able to function properly as intended.
  • If you have objects or devices on or under the main panel, use caution when adjusting the height or tilting angle.
  • Do not overtighten the screw knobs.
  • Do not use the unit if the plastic covers look cracked or if the screw knobs are stripped.
  • Do not expose the surfaces to direct sunlight or to extreme environmental conditions.
  • Do not use solvents or abrasive materials to clean the unit.
  • Do not climb on the base of the unit.
  • Do not allow small children to play with the unit.
  • Before moving the unit, unlock the front casters and secure or remove any object that might fall off while the unit is rolling.
  • The warranty does not extend to regular wear and tear, nor the manufacturer assumes liability for damages or consequences due to accidents, incorrect assembly, negligence, improper use, modifications, or not heeding the above warnings.

CARE AND MAINTENANCE

  • Clean the surfaces preferable with a clean cloth damped in a solution of mild soap and water, then dry with a clean towel.
  • If you decide to use a cleaning agent, test first on an area hidden from view such as underneath the tabletop.
  • Every 4 months, inspect the unit completely and make sure that all screws are tighten.
  • When transporting the unit to places far away, protect and secure the unit to avoid damage in transit.

TECHNI MOBILI WARRANTY

DESKS/LAPTOP CARTS/FILE CABINETS: LIMITED 5-YEAR WARRANTY

RTA Products, LLC warrants to the Original Purchaser who acquired a new product from RTA Products or its authorized resellers that this product will be free from defects in its workmanship and materials, under normal use and service conditions, as described herein. “Defects” as used in this warranty, is defined as any imperfections that impair the use of the furniture or product.
RTA Products LLC will replace any defective part, at its discretion, and without charge to the original purchaser other than the freight from the end consumer to RTA Products.
Replacement parts can only be supplied if parts are available. Items out of production may be unavailable. This warranty will be effective for the applicable time period beginning the date of purchase on your original sales receipt. RTA product’s obligation under this warranty is limited to repairing or replacing products or parts as provided herein. This product has been designed for and is intended for office and home-office use only. This warranty is Original Purchaser’s sole remedy for product defects, and this warranty does not extend to any product, or damage to any product, caused by or attributed to abuse or misuse, products used for commercial or rental purposes, use modifications of, or attachments to the product, and products or parts not used, maintained, or extended hereunder is in lieu of any and all other warranties, express or implied, including without limitations any implied warranty or merchantability or of fitness for a particular purpose. Please note, all desks made with PVC Laminate surface should not be exposed to direct sunlight, as it may damage the material. Damage of this nature is not covered under this warranty.
RTA Products will not be responsible for indirect, special, incidental or consequential damages.
This warranty is limited to merchandise purchased in the Continental United States, excludes AK, HI and PR. Some States do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights. You may also have other rights that may vary from state to state.

To file a Claim within the 48 contiguous United States:
Email us to warranty@rtaproducts.com to explain the defect and provide your name, address, phone number, model number of our product, date and place, and proof of purchase. Please provide pictures of the damage or defect.If we determine that a replacement will remedy the situation, and in order to determine the extent or the cause of the defect, purchaser may be requested to send the part in question at purchaser’s expense. Once we receive the part, we will examine it and determine whether the claim is valid (or not), and then proceed to send the replacement. We will ship the replacement at our expense.

Replacement Parts for International Customers & AK-HI-PR orders:
RTA Products will replace the part free of charge, while the customer is responsible for shipping costs plus any International local taxes or duties.

Customer Support

FRENCH

Scan QR to view the manual in French

VIDEO

Scan QR to view full assembly video
QR Code

ARABIC

Scan QR to view the manual in Arabic
QR Code

Do a quick inventory of all the parts and hardware listed below.

Support & Replacement Parts for the 48 contiguous United States:

Please email us at: support@rtaproducts.com

Replacement Parts for International Customers & AK-HI-PR orders:
RTA Products will replace the part free of charge, while the customer is responsible for shipping costs plus any International local taxes or duties.

Logo

Documents / Resources

| TECHNI MOBILI RTA-B002 Sit to Stand Rolling Adjustable Height Laptop Cart with Storage [pdf] Instruction Manual
RTA-B002 Sit to Stand Rolling Adjustable Height Laptop Cart with Storage, RTA-B002, Sit to Stand Rolling Adjustable Height Laptop Cart with Storage, Height Laptop Cart with Storage, with Storage
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

TECHNI MOBILi User Manuals

Related Manuals