Techni Mobili RTA-2336 Rotating Multi Positional Modern Desk Instruction Manual
- October 30, 2023
- TECHNI MOBILi
Table of Contents
Techni Mobili RTA-2336 Rotating Multi Positional Modern Desk Instruction
Manual
DIMENSIONS
MAXIMUM WEIGHT CAPACITIES
DO NOT exceed this limit Please use care and good judgement when placing objects on wood surface
PARTS LIST
-
Left Panel
-
Right Panel
-
Bottom Panel
-
Bottom Front Panel
-
Back Panel
-
Middle Front Panel
-
Top Panel
-
Slider
-
Top Drawer Front Panel
-
Bottom Drawer Front Panel
-
Drawer Left Panel
-
Drawer Right Panel
-
Drawer Bottom Panel
-
Drawer Back Panel
-
Drawer Connect
-
Studs
-
Rotating Structure
-
Support Tube
-
Big Table Top
-
Back Structure
-
Front Structure
-
Short Connect Tube
-
Long Connect Tube
-
Small Table Top
-
Big Side Panel
-
Support Structure
-
Caster
SCREWS LIST
PART| QTY| ITEM|
---|---|---|---
A| 24| 3X15MM|
B| 24| 6x40MM|
C| 16| 4X14MM|
D| 20| sxi5MM|
E| 8| 4x35MM|
F| 4| sxeomm|
G| 4| sxsaomm|
H| 5| oxsomm|
I| 6| |6x25MM|
J| 6| M6|
K| 4| »1emm|
| 1| |
| 1| |
| 1| |
HOW TO ASSEMBLE USING BOLTS AND CAM LOCKS
-
Screw the bolt into the corresponding panel.
-
In the other panel, insert and align the cam lock. Join the panels.
-
Turn the cam lock.
If the panel already comes with the cam lock inserted, make sure is aligned:
MISALIGNED:
TURN CAM LOCK TOPOINT TOWARDS THE HOLE
**CORRECT
**
GENERALASSEMBLY TIPS AND TROUBLESHOOTING DURING ASSEMBLY
-
Before you start assembling, make sure you have all the parts and necessary hardware by doing a quick inventory.
-
Follow the assembly instructions step by step, and do not skip any unless advised to do so by RTAPRODUCTS’ Customer Service.
-
On each step, and to avoid misalignments, always leave screws loose, and do not tighten them until all are in place.
-
In wood panels, the laminate might be covering the holes. If there are no visible holes: Pass the tip of your finger around the area where the hole should be, and press against the surface to feel the indentation. If the hole looks too small for the screw of bolt: carefully perforate the laminate with the tip of a pen.
-
In wood panels, some might have inserts that look like screws. Those inserts are either nuts or cam locks. Make sure they are aligned to receive the screws or bolts.
-
Make sure to use the correct screws or bolts, and do not overtight them. Using wrong screws or overnighting them might cause damage to the parts, and such damage is not covered by the product’s warranty.
ASSEMBLY STEPS
- Use screws A to assemble the Drawer Connects (15) to the Drawer Left and Right Panels (11 & 12).
**
**
-
Use screws D to assemble the Drawer Connects (15) to the Top Drawer Front Panel and Bottom Drawer Front Panel (9 & 10).
-
Slide in the Drawer Bottom Panel (13). Use screws E to assemble the Drawer Back Panels (14) to the Drawer Left and Right Panels (11 & 12).
-
Grab the 2 sets of the Drawer Sliders (8) and separate the flat ones from the “L” shaped ones. Place the drawer up side down as shown and use screws A to assemble the “L” shaped Sliders to the Drawer Left & Right Panels (11 & 12) as shown.
IMPORTANT: REFER TO THE DRAWINGS FOR THE CORRECT POSITION OF THE SLIDER. f they get installed incorrectly, the drawers will raise 1″ with a gap at the bottom and the top drawer will not close!
REPEAT STEP 3 TO 4 FOR THE OTHER DRAWER
- Insert the Studs (16) to the Left Panel, Right Panel, Back Structure and Front Structure (1,2,20 & 21).
-
Grab 2 sets of the Flat Sliders (8) and use screws A to assemble them to the Left & Right Panels (1 & 2) as shown. The wheel on the sliders go facing to the FRONT and the screw goes on the hole after the wheel as shown. Please pay attention to the direction of the panles.
-
First screw bolts B to the Bottom Front Panel and Back Panel (4 & 5), then assemble the Bottom Panel (3) as shown and as explained in page 5.
-
First screw bolts B to the Left Panel (1) and Right Panel (2), then assemble the Bottom Panel, Bottom Front Panel, Back Panel and Middle Front Panel (3,4,5 & 6) as shown and as explained in page 5.
-
First screw bolts B to the Top Panel (7), then assemble it to the Left and Right Panel (1 & 2) as shown and as explained in page 5.
-
Use screws G to assemble the Long Connect Tube (23) to the Back Structure and Front Structure (20 & 21).
-
Use screws F to assemble the Short Connect Tube (22) to the Back Structure and Front Structure (20 & 21).
-
Use screws C to assemble the Support Tube (18) to the Big Table Top (19).
-
Use screws H to assemble the Back Structure, Front Structure and Long Connect Tube (20,21 & 23) to the Big Table Top (19).
-
First screw bolts B to the Small Table Top (24), then assemble it to the Big Side Panel (25) as shown and as explained in page 5.
-
Use screws D to assemble the Support Structures (26) to the Small Table Top and Big Side Panel (24 & 25).
-
Use screws C to assemble the Support Tube (18) to the Small Table Top (24). Use screws | & J to assemble the Casters (27) to the Big Side Panel (25).
-
EXTREMELY IMPORTANT: PROCEED TO DO THIS STEP WITH CARE TO MAKE SURE THE INTERNAL PIECES DON’T COME OUT FROM THE TUBES. Place the rotating mechanism (17) with its part marked as “A” facing up, and remove the top screw. Carefully remove the piece “A” and the top tube marked as “E”, but be careful that the ball bearings, washers and other intemnal pieces don’t come out of the tubes. The rotating mechanism (17) will be disassembled into the following parts:
- Top tube ‘E”.
- Bottom tube ‘E”.
- Top piece “A”.
- Top scre
-
V Assemble the bottom tube “E” to the auxiliary panel (24) using screws (D) as shown.
-
Carefully and from undemeath insert the top tube “E” Into the bottom tube, making sure that the cylinder Comes out thru the hole of the ball bearing; place The pice “A”and secure the parts with the screw As shown.
-
Use screws |, J & K to assemble the Rotating Structure (17) to the Top Panel (7) as shown.
-
Use screws D to assemble the Rotating Structure (17) to the Big Table Top (19).
-
Tighten any and all screws. Insert the drawers into the cabinet, starting with the bottom drawer. You might have to insert it at a downward tilted angle.
CARE AND MAINTENANCE
- DO NOT EXPOSE THE SURFACES TO DIRECT SUNLIGHT OR EXTREME ENVIRONMENTAL CONDITIONS. ANY DAMAGE RESULTING FROM SUCH EXPOSURE IS NOT COVERED BY THE PRODUCT’S WARRANTY.
- THE PREFERABLE METHOD TO CLEAN THE SURFACES IS TO WIPE THEM USING A SOFT CLOTH DAMPENED WITH A SOLUTION SOAP AND WATER, THEN DRY WITH A CLEAN TOWEL.
- DO NOT SPRAY SOLVENTS OR CLEANING AGENTS DIRECTLY OVER THE SURFACES, STRUCTURAL TUBES OR METAL PARTS.
- DO NOT LEAN, SEAT OR STAND OVER THE UNIT.
- DO NOT ALLOW CHILDREN TO PLAY OVER/UNDER THE UNIT, NOR ALLOW THEM TO REACH INSIDE ANY COMPARTMENTS WITHOUT THE SUPERVISION OF AN ADULT.
- BEFORE MOVING OR TRANSPORTING THE UNIT, MAKE SURE THAT: e ALL HEAVY OBJECTS OR THAT MIGHT FELL OFF ARE REMOVED FROM THE UNIT.
- F THE UNIT ARE ON CASTERS (WHEELS), MAKE SURE THAT ALL ARE UNLOCKED.
- THE UNIT MUST BE HANDLED BY AT LEAST 2 PERSONS.
- WHEN LIFTING THE UNIT, USE BOTH OF YOUR HANDS, AND BEND YOUR KNEES. REMEMBER TO ALWAYS LIFT WITH YOUR LEGS, NOT YOUR BACK.
- IN CASE OF DAMAGE TO ANY PARTS, NOTIFY THE VENDOR AS SOON AS POSSIBLE.
- IN CASE OF GLASS BREAKAGE (IF THE UNIT HAS A GLASS TABLE TOP OR PARTS MADE OF GLASS) DO NOT HANDLE THE BROKEN GLASS WITH YOUR BEAR HANDS, AND CONTACT THE VENDOR IMMEDIATELY. DO NOT ALLOW CHILDREN NEAR THE BROKEN GLASS.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>