TECHNI MOBILi RTA-7310D Industrial Writing Desk Instruction Manual

TECHNI MOBILi RTA-7310D Industrial Writing Desk

Product Information: RTA-7310D

The RTA-7310D is a product that requires assembly. It comes with a main parts list consisting of frames, tubes, panels, and hardware. The product also includes a list of hardware, screws, and fittings required for assembly. The assembly instructions include tips and warnings that customers must read before starting the  assembly process. The manual also includes replacement parts service information for customers residing in the 48 contiguous United States.

Main Parts List

• Left frame x1
• Middle frame x1
• Right frame x1
• Bottom tube x1
• Top-front tube x1
• Top-back tube x1
• Back support tube (V) x2
• Top shelf support tube x2
• Top shelf horizontal tube x1
• Earphones hook x1
• CPU panel x1
• Left shelf panel x2
• Main panel x1
• Top shelf panel x1

List of Hardware, Screws and Fittings

Assembly Instructions

Before You Start the Assembly

• Do a quick inventory to make sure the package contains all the parts and hardware listed in the assembly instructions.
• To avoid misalignments, always leave the screws loose and tighten them until all pieces are positioned correctly.
• Missing, damaged and defective parts can be replaced at no cost to you. Please refer to the last pages on this manual.
• The replacement parts service is limited to the 48 contiguous United States. If you reside in Alaska, Hawaii, Puerto Rico, U.S. territories or other countries, please contact the supplier from where the unit was purchased.
• If during assembly you find an issue or need clarification, please contact our Customer Service for assistance. Please refer to the last pages on this manual.
• On each step read the instructions and analyze the illustrations thoroughly before proceeding to do the assembly.
• Make sure you understand which hardware will be used on each step. Using the wrong size of screw, bolt or pin might strip the threads or cause damage to the part in which it is being used.
• Do not overtighten or force the screws as they might break, strip, damage the threads of the holes or get stuck inside the part.
• Sometimes the laminate might cover partially or entirely the hole on a panel. If there is no visible hole for the screw, pass and press the tip of your finger over the area where the hole should be located to feel the indentation, and once found, carefully pierce the laminate to reveal the hole underneath.
• If the hole seems too small for the screw, first make sure you are using the correct size of screw and that it’s been installed in the correct hole. If the hole still appears to be too small, carefully pierce the laminate to reveal the hole’s actual size.

Assembly Steps

Step 1
Assemble the first left shelf 12 to the middle bars on the frames 1 and 2 with screws B from underneath.

• Hardware: B
• Quantity: 4 M6x30 Pcs
• Place the frame with this hole towards the back of the unit, it is needed for step 3.

Step 2
Assemble the second left shelf 12 to the bottom bars on the  frames 1 and 2 with screws B from underneath.

• Hardware: B
• Quantity: 4 M6x30 Pcs

Step 3
Assemble the back support tubes (V) 7 to the top-back tube 6 with screws A (M6x12) and C (M6x45).

• Hardware: A (M6x12), C (M6x45)
• Quantity: A1, C6
• Please pay attention to the orientation of the holes on all the tubes.

Instruction

• Please read carefully the assembly instructions before the installation.
• Do not discard this manual or any of the packaging material until the unit has been completely assembled.
• Might require two people.

MAIN PARTS LIST

MAIN PARTS LAYOUT (FOR REFERENCE)

LIST OF HARDWARE, SCREWS AND FITTINGS

LIST OF HARDWARE, SCREWS AND FITTINGS|
---|---
PART| QTY| ITEM|  |  | PART| QTY| ITEM|  |
A| 1| M6x12| |

F

| ****

2

| Locking caster| **|
B| 28| M6x30| **|

G

| ****

2

| Non-Locking caster| **|
C| 10| M6x45| **|
| 1| Screwdriver| **|
D| 16| M3.5×12| **|
| 1| Wrench (Spanner)| **|
E| 2| M6x2| **|
|  | 1| Allen Wrench| ****|

BEFORE YOU START THE ASSEMBLY, PLEASE READ THE FOLLOWING TIPS AND WARNINGS.

• Do a quick inventory to make sure the package contains all the parts and hardware listed in the assembly instructions.
• Missing, damaged and defective parts can be replaced at no cost to you. Please refer to the last pages on this manual.
• The replacement parts service is limited to the 48 contiguous United States. If you reside in Alaska, Hawaii, Puerto Rico, U.S. territories or other countries, please contact the supplier from where the unit was purchased.
• If during assembly you find an issue or need clarification, please contact our Customer Service for assistance. Please refer to the last pages on this manual.
• On each step read the instructions and analyze the illustrations thoroughly before proceeding to do the assembly.
• Make sure you understand which hardware will be used on each step. Using the wrong size of screw, bolt or pin might strip the threads or cause damage to the part in which it is being used.
• To avoid misalignments, always leave the screws loose and tighten them until all pieces are positioned correctly.
• Do not overtighten or force the screws as they might break, strip, damage the threads of the holes or get stuck inside the part.
• Sometimes the laminate might cover partially or entirely the hole on a panel. If there is no visible hole for the screw, pass and press the tip of your finger over the area where the hole should be located to feel the indentation, and once found, carefully pierce the laminate to reveal the hole underneath.
• If the hole seems too small for the screw, first make sure you are using the correct size of screw and that it’s been installed in the correct hole. If the hole still appears to be too small, carefully pierce the laminate to reveal the hole’s actual size.

PRODUCT ASSEMBLY STEPS

• STEP 1
  Assemble the first left shelf 12 to the middle bars on the frames 1 and 2 with screws B from underneath.
  

• STEP 2
  Assemble the second left shelf 12 to the bottom bars on the frames 1 and 2 with screws B from underneath.
  

• STEP 3
  Bring the cabinet built in step 2 to the upright position, then with the help of another person:

  • Assemble the tubes 4, 5 and 6 to the middle frame 2 in their respective positions with screws C.
  • Assemble the right frame 3 to the tubes 4, 5 and 6 with screws C.
  • Attach the hook 10 to the frame 3 with screw A from the inside.
    

• STEP 4

  • Assemble the support tubes 7 to the top tube 6 on the back of the unit with screws C from outside and nut caps E from inside.
  • Assemble the support tubes 7 to the bottom tube 4 with screws B from underneath.
    Note: If you don’t see holes for the screws on the tubes 4 and 6, review step 3 for the correct assembly of those tubes.
    

• STEP 5
  Assemble the top shelf support tubes 8 to the shelf horizontal tube 9 with screws C.
  

• STEP 6
  Assemble the tubes 8 and 9 to the top shelf panel 14 with screws B.
  

• STEP 7
  With the help of another person, assemble the main panel 13 to the tubes 8 with screws B making sure the bottom surface faces UP like shown in the illustration.
  

• STEP 8
  With the help of another person, assemble the main panel 13 to the frames 1, 2 and 3 and to the tubes 5 and 6 with screws B from underneath.
  Note: If you don’t see holes for the screws on the tubes 5 and 6, review step 3 for the correct assembly of those tubes.
  

• STEP 9
  Assemble the casters F and G to the CPU panel 11 with screws D, making sure the Locking casters F are attached on the same side that will be considered the FRONT of the cart.
  

ALL DONE!
Give yourself a nice pat on the back. You did a great job!
You can keep the CPU cart under the desk or on the side according to your preference.

CARE, MAINTENANCE AND SAFETY WARNINGS:

• Do not exceed the indicated weight limits.
• Do not expose the surfaces to direct sunlight or to extreme environmental conditions.
• Clean the surfaces preferable with a clean cloth damped in a solution of mild soap and water, then dry with a clean towel.
• Do not use solvents or abrasive materials to clean the unit.
• If you decide to use a cleaning agent, test first on an area hidden from view such as underneath the tabletop.
• Do not sit on the unit or lean against it.
• Do not allow small children to play under or over the unit.
• Do not allow small children to play with the CPU cart or use it as a vehicle.
• Do not pull, push or drag the unit to move it for more than 1 feet. The unit must be lifted by at least 2 persons when moving in the same or adjacent rooms.
• Before moving the unit, make sure to secure or remove any object that is heavy or might fall off. Please note that lifting from the tabletop with too much weight on the product might lead to part damage/separation.
• When lifting the unit, grab the frame, not the main panel, and use both hands and bend your knees, not your backs.
• When transporting the unit to places far away, protect and secure the unit to avoid damage in transit.
• Shall any part of the unit become defective during the warranty period, replacement parts might be available to you at no charge. Please refer to the last pages on this manual.
• The warranty does not extend to regular wear and tear, nor the manufacturer assumes liability for damages or consequences due to accidents, incorrect assembly, negligence, improper use, modifications, or not heeding the above warnings.

TECHNI MOBILI WARRANTY

DESKS/LAPTOP CARTS/FILE CABINETS: LIMITED 5-YEAR WARRANTY TV Stand/Entertainment Center: 2 YEAR WARRANTY
RTA Products, LLC warrants to the Original Purchaser who acquired a new product from RTA Products or its authorized resellers that this product will be free from defects in its workmanship and materials, under normal use and service conditions, as described herein. “Defects” as used in this warranty, is defined as any imperfections that impair the use of the furniture or product. RTA Products LLC will replace any defective part, at its discretion, and without charge to the original purchaser other than the freight from the end consumer to RTA Products.
Replacement parts can only be supplied if parts are available. Items out of production may be unavailable. This warranty will be effective for the applicable time period beginning the date of purchase on your original sales receipt. RTA product’s obligation under this warranty is limited to repairing or replacing products or parts as provided herein. This product has been designed for and is intended for office and home-office use only. This warranty is Original Purchaser’s sole remedy for product defects, and this warranty does not extend to any product, or damage to any product, caused by or attributed to abuse or misuse, products used for commercial or rental purposes, use modifications of, or attachments to the product, and products or parts not used, maintained, or extended hereunder is in lieu of any and all other warranties, express or implied, including without limitations any implied warranty or merchantability or of fitness for a particular purpose. Please note, all desks made with PVC Laminate surface should not be exposed to direct sunlight, as it may damage the material. Damage of this nature is not covered under this warranty.
RTA Products will not be responsible for indirect, special, incidental or consequential damages. This warranty is limited to merchandise purchased in the Continental United States. Some States do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights. You may also have other rights that may vary from state to state.
RTA Products will advise you of the procedure to follow in making warranty claims. The following are the procedures for warranty claims:

• Call us Monday – Friday, from 9am-5pm (Eastern Time) at (866) 782-5520 to explain the defect and give your name, address and phone number. Please have ready the model number of our product, date and place of purchase. You can also write to us by e- mail to [email protected] and include the same information.
• If we determine that replacement will remedy the situation, and in order to determine the extent or the cause of the defect, purchaser will need to send the part in question at purchaser’s expense. Once we receive the part, we will examine it and determine whether the claim is valid (or not), and then proceed to send the replacement. We will ship the replacement at our expense.

FOR SEVERAL HELP OPTIONS
INCLUDING REPLACEMENT PARTS ORDERS

VISIT: WWW.TECHNIMOBILI.COM
CLICK ON SUPPORT TAB

Scan QR Code to order replacement parts
OR EMAIL US: [email protected]

References

• Techni Mobili Home and Office Furniture

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>