TECHNI MOBILI RTA-B005 Sit-To-Stand Rolling Adjustable Laptop Cart with Storage Instruction Manual
- October 30, 2023
- TECHNI MOBILi
Table of Contents
RTA-B005 Sit-To-Stand Rolling Adjustable Laptop Cart with Storage
Instruction Manual SIT-TO-STAND ROLLING ADJUSTABLE
LAPTOP CART WITH STORAGE
MODEL RTA-B005
ASSEMBLY INSTRUCTIONS
Thank you for purchasing our product
Scan to view full assembly videohttps://www.youtube.com/watch?v=oAI9ZqCO5OI
| Do not discard this manual or any of the packaging material until the unit
has been completely assembled.
---|---
| Please read carefully the assembly instructions before the installation.
https://www.youtube.com/watch?v=oAI9ZqCO5OI| Scan this QR code to view the
complete assembly video online.
| For individual Step videos – please use the QR code found on the
corresponding step within the manual.
| Please be kind to our planet, when done with the assembly, recycle any of
the packaging materials that is accepted by your city or recycling service.
| Do a quick inventory of all the parts and hardware listed below
---|---
| Missing, damaged and defective parts can be replaced at no cost to you.
Please refer to the last pages on this manual.
| The replacement parts service is limited to the 48 contiguous United States.
If you reside in AK, HI, PR, U.S. territories or other countries, please
contact the supplier from where the unit was purchased.
MAIN PARTS LIST
MAIN PARTS LAYOUT (For reference)
HARDWARE LIST
INCLUDED TOOLS
1| Phillips Screwdriver|
---|---|---
CAM BOLT AND CAM LOCK TUTORIAL
THE INSTRUCTIONS BELOW ARE NOT ACTUAL ASSEMBLY STEPSThis unit uses
cam bolts and locks (also known as mini fixes).
If you are not familiar with this kind of hardware, the below is a tutorial
that explains how to use them on the steps where they are required.
-
Screw the bolt into the indicated hole on the panel indicated in the assembly step.
-
Join the other panel (with the big hole) to the panel with the bolt. If it comes with the cam locks already pre-installed, make sure to align them to receive the bolt’s head (refer to point 3). There might be a very small gap between the panels which is normal. If the cam locks come pre-in stalled, make sure they are aligned (see point 3).
-
Insert the cam lock on the panel with the big hole making sure it goes aligned to receive the bolt’s head.
-
Use a Phillips screwdriver to turn the cam lock clockwise. This will lock the panels togheter and also will close any gaps.
BEFORE YOU START THE ASSEMBLY, PLEASE READ THE FOLLOWING TIPS AND WARNINGS.
• Do not discard this manual or any of the packaging material until the unit
has been completely assembled.|
---|---
• If during assembly you find an issue or need clarification, please contact
our Customer Service for assistance. Please refer to the last pages on this
manual.|
• On each step read the instructions thoroughly and analyze the illustrations
before proceeding to do the assembly.
• Follow the instructions step by step and do not skip any unless our Customer
Service advises it is OK to do so.|
• Make sure you understand which hardware will be used on each step. Using the
wrong size of screw, bolt or pin might strip the threads or cause damage to
the part in which it is being used.|
• To avoid misalignments, always leave the screws loose and tighten them until
all pieces are positioned correctly.|
• Do not overtighten or force the screws as they might break, strip, damage
the threads of the holes or get stuck inside the part.|
• If the hole seems too small for the screw, make sure you are using the
correct size of screw and/or that you are installing it in the correct hole.|
• Sometimes on the panels the laminate or material might be covering the hole
partially or entirely. If there is no visible
hole or it seems too small, pass and press the tip of your finger over the
area where the hole should be located to feel its indentation, and once found,
carefully pierce the laminate to uncover the hole underneath.|
ASSEMBLY STEPS
<https://www.youtube.com/watch?v=_PQfPNOWreA>
Attach the magnet 17-A to the bottom surface of the middle upper shelf 8 with
screws F.
Attach the small steel plate 17-B to the inside surface of the shelf door 18
with screws F.
https://www.youtube.com/watch?v=DRfWF8muyFM
Screw the bolts D into panel 1.
Join panel 4 to panel 1 and turn the cam locks as explained in page 4.
Assemble panel 6 to panel 1 in the same way making sure the surface with the
cam locks towards the BOTTOM.
Join panel 5 to panel 1.
https://www.youtube.com/watch?v=eyB_t48QTUE
Insert the metal pin H into the corresponding hole on panel 1.
Attach the door panel 18 to the pin H, making sure the metal plate is visible
as shown.
https://www.youtube.com/watch?v=Rrw9bdJTzJM
Attach the bolts D to the right side panel 2 into the indicated holes.
Insert the metal pin H into the door 18.
Assemble panel 2 to panels 4, 5, 6 and 18 as shown and as explained in page 4.
https://www.youtube.com/watch?v=PtYHFzK_vLY
Use screws A to assemble the casters 3 to the bottom surface of the bottom
base panel 7 in the following positions:
The Locking casters 3-L go at the front of the panel.
The Non-locking casters 3-N go at the back of the panel.
https://www.youtube.com/watch?v=3fCl1k4MfOM
Screw the bolts D into the indicated holes on the top surface of panel 7.
Join the main frame to the base and lock the pieces together by turning the
cam locks on panels 1, 2 and 4 as shown and as explained in page 4.
https://www.youtube.com/watch?v=1fGlemeIdOE
Screw the bolts D to the middle upper shelf 8.
Assemble the shelf 8 to panels 1, 2 and 4 as explained in page 4.
https://www.youtube.com/watch?v=_F_OEFK3jP0
Assemble the lateral support bars 9 to the base panel 7 with screws C from
underneath. The screws go through the base panel and into the bars.
Assemble the bars 9 to the side panels 1 and 2 with screws C from the side.
The screws go through the bars and into the side panels.
https://www.youtube.com/watch?v=36pds6PLwVU
EXTREMELY IMPORTANT!
Follow this step EXACTLY as instructed! An incorrect assembly leaves the
tilting mechanism and main panel prone to moving or sliding, and even might
flip down forwards unexpectedly under any weight .
- Place the curved connectors I over the threaded holes of the lifting tubes 10.
- Place the washer I over the connector I.
- Connect the right tiltilg mechanism 13 to the tube 10.
- Insert and screw the screw knob 16 into the tube 10. The screw knob goes through the mechanism 13, the washer I, the connector I and into the tube 10.
- Repeat the procedure for the left tilting mechanism 14.
THE SOFT PLASTIC WASHER MUST GO IN BETWEEN THE CONNECTOR AND THE MECHANISM, AS
IT PURPOSE IS TO CREATE THE NECESSARY FRICTION THAT KEEPS THE MECHANISM FIRM
WITHOUT MOVING.
DO NOT PLACE THE WASHER OVER THE MECHANISM, IT MUST GO UNDER IT.
IF THE SOFT PLASTIC WASHER IS MISSING, DO NOT REPLACE IT WITH ANY OTHER KIND;
DO NOT USE METAL OR HARD PLASTIC WASHERS.
https://www.youtube.com/watch?v=oRHkZan0zdw
Assemble the tilting mechanisms 13 and 14 to the main panel 12 in their
respective sides with screws E.
https://www.youtube.com/watch?v=nbMQYGXNMJY
Place the plastic covers 11 over the lateral bars 9 with their threaded holes
facing towards the outside.
Slide the lifting tubes 10 through the plastic covers 11 and into the bars 9.
Insert the screw knobs 16 into the plastic covers 11, but do not tighten yet.
https://www.youtube.com/watch?v=S_yyklmx6ik
Lift the main panel 12 about 6 inches and tighten the screw knobs 16.
Assemble the protection rail 15 to the main panel 12 with its curvature
towards the front with screws B from underneath.https://www.youtube.com/watch?v=trky9oCS_ns
Assemble the handle 19 to the door 18 with screw G.
ALL DONE!
Give yourself a nice pat on the back, you did a great job!
ENJOY YOUR NEW UNIT!
FUNCTIONS / ADJUSTMENTS
ROLLING:
Unlock the front casters to allow free movement.
LIFTING:
Loosen the screw knobs to lift, then tighten again.
TILTING:
Loosen the screw knobs to tilt, then tighten again.
WEIGHT LIMITS
WARNINGS
- Do not exceed the indicated weight limits.
- Do not expose the surfaces to direct sunlight or to extreme environmental conditions.
- Do not use solvents or abrasive materials to clean the unit.
- Do not climb on the base of the unit.
- Do not allow small children to play with the unit.
- Before moving the unit, unlock the front casters and make sure to secure or remove any object on it that might fall off.
- Do not overtighten the screw knobs.
- Make sure that the tilting mechanisms are properly assembled as instructed in page 9 step 9.
- An incorrect assembly leaves the tilting mechanism unsecured, and the main top panel will not hold enough weight on it and even might flip down forwards unexpectedly.
- If you have objects or devices on or under the main panel, use caution when adjusting the height or tilting angle.
- It is recommended to first tilt the main panel, then place the objects or devices, but pay attention to if they will be properly retained by the protection rail. If the object or device seems that might tip over, reduce the tilting angle.
- Do not use the unit if the plastic covers or screw knobs look cracked or if they are stripped.
CARE AND MAINTENANCE
- Clean the surfaces preferable with a clean cloth damped in a solution of mild soap and water, then dry with a clean towel.
- If you decide to use a cleaning agent, test first on an area hidden from view such as underneath the tabletop.
- Every 4 months, inspect the unit completely and make sure that all screws are tighten.
- When transporting the unit to places far away, protect and secure the unit to avoid damage in transit.
- Shall any part of the unit become defective during the warranty period, replacement parts might be available to you at no charge. Please refer to the last pages on this manual.
- The warranty does not extend to regular wear and tear, nor the manufacturer assumes liability for damages or consequences due to accidents, incorrect assembly, negligence, improper use, modifications, or not heeding the above warnings.
TECHNI MOBILI WARRANTY
DESKS/LAPTOP CARTS/FILE CABINETS: LIMITED 5-YEAR WARRANTY
RTA Products, LLC warrants to the Original Purchaser who acquired a new
product from RTA Products or its authorized resellers that this product will
be free from defects in its workmanship and materials, under normal use and
service conditions, as described herein. “Defects” as used in this warranty,
is defined as any imperfections that impair the use of the furniture or
product. RTA Products LLC will replace any defective part, at its discretion,
and without charge to the original purchaser other than the freight from the
end consumer to RTA Products.
Replacement parts can only be supplied if parts are available. Items out of
production may be unavailable. This warranty will be effective for the
applicable time period beginning the date of purchase on your original sales
receipt. RTA product’s obligation under this warranty is limited to repairing
or replacing products or parts as provided herein. This product has been
designed for and is intended for office and home-office use only. This
warranty is Original Purchaser’s sole remedy for product defects, and this
warranty does not extend to any product, or damage to any product, caused by
or attributed to abuse or misuse, products used for commercial or rental
purposes, use modifications of, or attachments to the product, and products or
parts not used, maintained, or extended hereunder is in lieu of any and all
other warranties, express or implied, including without limitations any
implied warranty or merchantability or of fitness for a particular purpose.
Please note, all desks made with PVC Laminate surface should not be exposed to
direct sunlight, as it may damage the material. Damage of this nature is not
covered under this warranty.
RTA Products will not be responsible for indirect, special, incidental or
consequential damages. This warranty is limited to merchandise purchased in
the Continental United States, excludes AK, HI and PR. Some States do not
allow the exclusion or limitation of incidental or consequential damages, so
the above limitations or exclusions may not apply to you. This warranty gives
you specific legal rights. You may also have other rights that may vary from
state to state.
RTA Products will advise you of the procedure to follow in making warranty
claims. The following are the procedures for warranty claims:
a. Call us Monday – Friday, from 9am-5pm (Eastern Time) at (866) 782-5520 to
explain the defect and give your name, address and phone number. Please have
ready the model number of our product, date and place of purchase. You can
also write to us by e-mail to warranty@rtaproducts.com and include the same
information.
b. If we determine that replacement will remedy the situation, and in order to
determine the extent or the cause of the defect, purchaser will need to send
the part in question at purchaser’s expense. Once we receive the part, we will
examine it and determine whether the claim is valid (or not), and then proceed
to send the replacement. We will ship the replacement at our expense.
FOR SEVERAL HELP OPTIONS
INCLUDING REPLACEMENT PARTS ORDERS
VISIT: WWW.TECHNIMOBILI.COM
AND CLICK ON SUPPORT TAB
Or scan the following QR Code:
https://technimobili.com/pages/support
Scan the following QR Code to order replacement parts:
https://technimobili.com/pages/order-parts
EMAIL US: support@rtaproducts.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>