TECHNI MOBILI RTA-S07 Rolling Storage and File Cabinet Instruction Manual
- October 30, 2023
- TECHNI MOBILi
Table of Contents
ROLLING STORAGE AND FILE CABINET
MODEL RTA-S07
ASSEMBLY INSTRUCTIONS
RTA-S07 Rolling Storage and File Cabinet
Thank you for purchasing our product
• Do not discard this manual or any of the packaging material until the unit
has been completely assembled.| 
---|---
• Please read carefully the assembly instructions before the installation.|
• Scan this QR code to view the complete assembly video online.|
• For individual Step videos – please use the QR code found on the corresponding step within the manual.|
**<https://youtu.be/C6tI67gHkSM>** • After the item is assembled, you can use rubbing alcohol to erase or remove
the visible part numbers printed or labeled on the pieces.|
• Please be kind to our planet, when done with the assembly, recycle any of
the packaging materials that is accepted by your city or recycling service.|
Do a quick inventory of all the parts and hardware listed below|
Missing, damaged and defective parts can be replaced at no cost to you. Please
refer to the last pages on this manual.|
The replacement parts service is limited to the 48 contiguous United States.
If you reside in AK, HI, PR, U.S. territories or other countries, please
contact the supplier from where the unit was purchased.|
MAIN PARTS LIST
MAIN PARTS LAYOUT
(For reference)
HARDWARE LIST AND INCLUDED TOOLS
| PART | QTY | SIZE | ITEM |
|---|---|---|---|
| A | 20 | M6x40 Bolt | |
| B | 12 | M4x35 | |
| C | 40 | M3x15 | |
| D | 6 | M4x20 | |
| E | 18 | M4x14 | |
| F | 1 | M6x12 |
INCLUDED TOOLS
1| Phillips Screwdriver|
---|---|---
1| Hex wrench (spanner)|
RTA-S07
CAM BOLT AND CAM LOCK TUTORIAL
THE INSTRUCTIONS BELOW ARE NOT ACTUAL ASSEMBLY STEPS
This unit uses cam bolts and locks (also known as mini
fixes).
If you are not familiar with this kind of hardware, the below is a tutorial
that explains how to use them on the steps where they are required.
-
Screw the bolt into the indicated hole on the panel indicated in the assembly step.
-
Join the other panel (with the big hole) to the panel with the bolt. If it comes with the cam locks already pre-installed, make sure to align them to receive the bolt’s head (refer to point 3). There might be a very small gap between the panels which is normal.
If the cam locks come pre-in stalled, make sure they are aligned (see point 3). -
Insert the cam lock on the panel with the big hole making sure it goes aligned to receive the bolt’s head.
-
Use a Phillips screwdriver to turn the cam lock clockwise. This will lock the panels togheter and also will close any gaps.
BEFORE YOU START THE ASSEMBLY, PLEASE READ THE FOLLOWING TIPS AND WARNINGS.
• Do not discard this manual or any of the packaging material until the unit
has been completely assembled.|
---|---
• If during assembly you find an issue or need clarification, please contact
our Customer Service for assistance. Please refer to the last pages on this
manual.|
• On each step read the instructions thoroughly and analyze the illustrations
before proceeding to do the assembly.
• Follow the instructions step by step and do not skip any unless our Customer
Service advises it is OK to do so.|
• Make sure you understand which hardware will be used on each step. Using the
wrong size of screw, bolt or pin might strip the threads or cause damage to
the part in which it is being used.| 
• To avoid misalignments, always leave the screws loose and tighten them until
all pieces are positioned correctly.|
• Do not overtighten or force the screws as they might break, strip, damage
the threads of the holes or get stuck inside the part.|
• If the hole seems too small for the screw, make sure you are using the
correct size of screw and/or that you are installing it in the correct hole.|
• Sometimes on the panels the laminate or material might be covering the hole
partially or entirely. If there is no visible hole or it seems too small, pass
and press the tip of your finger over the area where the hole should be
located to feel its indentation, and once found, carefully pierce the laminate
to uncover the hole underneath.|
ASSEMBLY STEPS
INSERT THE PIECES IN THE EXACT ORDER SHOWN
- Slide one piece of the locking fitting 22A through the metal bar 22E with its flat side UP.
- Slide all 3 pieces of the locking fitting 22C facing UP, align each piece within the markings on the bar, and insert and tighten the tiny screws 22F to lock the pieces on the bar.
- Slide the second piece 22A through the metal bar 22E with its flat side UP.
STEP 2
Place the locking system 22 inside the big channel of the right side panel 15
with the 2 rods facing UP and toward the TOP, and secure the fittings 22A with
screws C as shown.
STEP 3
Grab all the 3 sets of sliders 12 and separate them into 2 groups according to their shape:
- The “flat” ones will be used on the next step.
- The “L” shaped will be used until step 17, set them aside.
STEP 4
The wheel goes facing towards the front, and faces down with 2 holes above
it.
The sliders attach at the front on the 2nd hole.
The sliders will be flushed with the front edge of the panels.
The narrow grooves on the panels are located at the back.
Assemble the “Flat” sliders 12 to the 3 sets of holes on the side panels 14
and 15 with screws C. Please note:
STEP 5
https://youtu.be
/Qw5vErQ-lx8
STEP 6
Use screws E to attach the Locking casters 3L to the bottom surface of the
bottom panel 16 at the front, and the non-locking casters 3N at the back.
https://youtu.be/jLje_CG5l2s
STEP 7
On the bottom panel 16, first make sure that the cam locks are properly
aligned to receive the bolts.
Join the side panels 14 and 15 to panel 16, and turn the cam locks to lock all
the pieces together as explained in page 4.
https://youtu.be
/2a_Z-NreDn8
STEP 8
- Slide the back board 17 through the grooves of panels 14 and 15 and into the groove of panel 16
- Assemble the top panel 18 to panels 14 and 15 as explained in page 4.
https://youtu.be/QCiavJDMWKE
https://youtu.be/ZrdN4cNl8WE
STEP 11
- Assemble the small drawer side panels 1 and 2 to the top drawer front panel 4 and also to the middle drawer front panel 21 in their respective sides and as explained in page 4.
Assemble the file drawer side panels 7 and 8 to the file drawer front panel 9 in their respective sides and as explained in page 4.
STEP 12
Slide the drawer bottom board 5 through the grooves of the side panels on
all 3 drawers, and into the groove of the front panels respectivelly, as
shown.
STEP 13
- On the two small drawers, assemble the back panel 6 to the side panels 1 and 2 with screws B as shown.
- On the file drawer, assemble the back panel 10 to the side panels 7 and 8 with screws B as shown.
STEP 14
Attach the handles 13 to the front panels on all 3 drawers with screws D.
STEP 15
For the file drawer, insert the file tubes 11 through the holes on the back
panel 10 and screw them into the front panel 9, but DO NOT OVERTIGHTEN to
avoid accidental damage humps or perforation. Please note that such kind of
damage is not covered by the product’s warranty.
https://youtu.be/eKdE50wXtjI
STEP 16
For the small top drawer with lock, attach the lock 22D from inside of
panel 4 with screws C, but make sure that the keys will make the rod rotate
from the bottom to the top in a counter-clock motion.
Attach the ring 22G to the lock 22D at the front.
STEP 17
With all the drawers upside-down, attach to them the “L” shaped sets of
sliders 12 with screws C. Please note that the wheels go facing towards the
back of the drawers, and they should not protrude, otherwise, the drawers rise
1″ and won’t fit in the cabinet.
- Insert the bottom and the middle drawer into the cabinet, at an angle facing down. Make sure the wheels from the drawers slide in the middle of the sliders inside the cabinet, not on top of them.
- Before you insert the top drawer, make sure the lock turns from bottom to top in counter-clockwise motion, and if it doesn’t, review step 16 for the correct assembly of the lock.
AN INCORRECT ASSEMBLY OF THE LOCK MIGHT LEAD TO THE TOP DRAWER GETTING STUCK AND LOCKED, UNABLE TO OPEN.
Insert the top drawer into the cabinet at an angle facing down. If it does not enter and hits the top of the cabinet, review the assembly done in steps 1, 2, 4, 9, 16 and 17 for the correct assembly of the locking fittings and sliders.
ALL DONE!
Give yourself a nice pat on the back, you did a great job!
ENJOY YOUR NEW UNIT!
TROUBLESHOOTING THE LOCK SYSTEM
- If the item does not want to lock, review the assembly done in pages 6, 7, 10, 12 and 17 for the correct assembly of the locking fittings and the drawer sliders.
- The middle and bottom drawers will lock only if they are closed completely.
- If the keys are lost but the cabinet is unlock, replace them with a new set of lock and keys.
- If the cabinet is locked, and the keys are lost or don’t want to turn, please contact our Support Department to receive instructions for solving this problem.
WEIGHT LIMITS
WARNINGS
- Do not exceed the indicated weight limits.
- Do not expose the surfaces to direct sunlight or to extreme environmental conditions.
- Do not use solvents or abrasive materials to clean the unit.
- Do not sit on the unit or lean against it.
- Do not allow small children to climb over the unit.
- Keep the item locked if there are small children around.
- Before moving the unit, make sure to unlock the front wheels, and secure or remove any object that is on the top panel that might fall off.
CARE AND MAINTENANCE
- Clean the surfaces preferable with a clean cloth damped in a solution of mild soap and water, then dry with a clean towel.
- If you decide to use a cleaning agent, test first on an area hidden from view such as underneath one of the drawers.
- Every 4 months, inspect the unit completely and make sure that all screws are tighten.
- When transporting the unit to places far away, protect and secure the unit to avoid damage in transit.
- Shall any part of the unit become defective during the warranty period, replacement parts might be available to you at no charge. Please refer to the last pages on this manual.
- The warranty does not extend to regular wear and tear, nor the manufacturer assumes liability for damages or consequences due to accidents, incorrect assembly, negligence, improper use, modifications, or not heeding the above warnings.
TECHNI MOBILI WARRANTY
DESKS/LAPTOP CARTS/FILE CABINETS: LIMITED 5-YEAR WARRANTY
RTA Products, LLC warrants to the Original Purchaser who acquired a new
product from RTA Products or its authorized resellers that this product will
be free from defects in its workmanship and materials, under normal use and
service conditions, as described herein. “Defects” as used in this warranty,
is defined as any imperfections that impair the use of the furniture or
product. RTA Products LLC will replace any defective part, at its discretion,
and without charge to the original purchaser other than the freight from the
end consumer to RTA Products.
Replacement parts can only be supplied if parts are available. Items out of
production may be unavailable. This warranty will be effective for the
applicable time period beginning the date of purchase on your original sales
receipt. RTA product’s obligation under this warranty is limited to repairing
or replacing products or parts as provided herein. This product has been
designed for and is intended for office and home-office use only. This
warranty is Original Purchaser’s sole remedy for product defects, and this
warranty does not extend to any product, or damage to any product, caused by
or attributed to abuse or misuse, products used for commercial or rental
purposes, use modifications of, or attachments to the product, and products or
parts not used, maintained, or extended hereunder is in lieu of any and all
other warranties, express or implied, including without limitations any
implied warranty or merchantability or of fitness for a particular purpose.
Please note, all desks made with PVC Laminate surface should not be exposed to
direct sunlight, as it may damage the material. Damage of this nature is not
covered under this warranty.
RTA Products will not be responsible for indirect, special, incidental or
consequential damages. This warranty is limited to merchandise purchased in
the Continental United States, excludes AK, HI and PR. Some States do not
allow the exclusion or limitation of incidental or consequential damages, so
the above limitations or exclusions may not apply to you. This warranty gives
you specific legal rights. You may also have other rights that may vary from
state to state.
RTA Products will advise you of the procedure to follow in making warranty
claims. The following are the procedures for warranty claims:
a. Call us Monday – Friday, from 9am-5pm (Eastern Time) at (866) 782-5520 to
explain the defect and give your name, address and phone number. Please have
ready the model number of our product, date and place of purchase. You can
also write to us by e-mail to
warranty@rtaproducts.com and include
the same information.
b. If we determine that replacement will remedy the situation, and in order to
determine the extent or the cause of the defect, purchaser will need to send
the part in question at purchaser’s expense. Once we receive the part, we will
examine it and determine whether the claim is valid (or not), and then proceed
to send the replacement. We will ship the replacement at our expense.
FOR SEVERAL HELP OPTIONS
INCLUDING REPLACEMENT PARTS ORDERS
VISIT: WWW.TECHNIMOBILI.COM
AND CLICK ON SUPPORT TAB Or scan the following QR Code:
https://technimobili.com/pages/support
Scan the following QR Code to order replacement parts:
https://technimobili.com/pages/order-parts
EMAIL US:
support@rtaproducts.com
Documents / Resources
|
TECHNI MOBILI RTA-S07 Rolling Storage and File
Cabinet
[pdf] Instruction Manual
RTA-S07, RTA-S07 Rolling Storage and File Cabinet, Rolling Storage and File
Cabinet, Storage and File Cabinet, File Cabinet, Cabinet
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>