TECHNI MOBILI RTA-8404 Classic Computer Desk Instruction Manual
- October 30, 2023
- TECHNI MOBILi
Table of Contents
CLASSIC COMPUTER DESK WITH MULTIPLE DRAWERS
MODEL RTA-8404
ASEEMBLY INSTRUCTIONS
RTA-8404 Classic Computer Desk
Thank you for purchasing our product
Please note that this product comes packaged in 2 separate boxes
Scan QR to view full assembly videohttps://youtu.be/kqIDIduTom8
• This product comes split in 2 separate boxes.|
---|---
• Do not discard this manual or any of the packaging material until the unit
has been completely assembled.|
• Please read carefully the assembly instructions before the installation.|
• The assembly might require of 2 persons for certain steps. Before you start
the installation, make sure there is someone nearby to help you.|
• Scan this QR code to view the complete assembly video online.| 
• For individual Step videos – please use the QR code found on the
corresponding step within the manual.| 
Do a quick inventory of all the parts and hardware listed below| Do a quick
inventory of all the parts and hardware listed below| The replacement parts
service is limited to the 48 contiguous United States.
If you reside in AK, HI, PR, U.S. territories or other countries,
please contact the supplier from where the unit was purchased.
---|---|---
| |
MAIN PARTS LIST
MAIN PARTS LAYOUT (For reference)
HARDWARE LIST
CAM BOLT AND CAM LOCK TUTORIAL THE INSTRUCTIONS BELOW ARE NOT ACTUAL ASSEMBLY STEPS
This unit uses cam bolts and locks (also known as mini fixes).
If you are not familiar with this kind of hardware, the below is a tutorial
that explains how to use them on the steps where they are required.
- Screw the bolt into the indicated hole on the panel indicated in the assembly step.
- Insert the cam lock on the panel with the big hole making sure it goes aligned to receive the bolt’s head.
- Join the other panel (with the big hole) to the panel with the bolt. If it comes with the cam locks already pre-installed, make sure to align them to receive the bolt’s head (refer to point
- There might be a very small gap between the panels which is normal.
- Use a Phillips screwdriver to turn the cam lock clockwise. This will lock the panels together and also will close any gaps.
BEFORE YOU START THE ASSEMBLY, PLEASE READ THE FOLLOWING TIPS AND WARNINGS.
• Do not discard this manual or any of the packaging material until the unit
has been completely assembled.|
---|---
• If during assembly you find an issue or need clarification, please contact
our Customer Service for assistance. Please refer to the last pages on this
manual.|
• On each step read the instructions thoroughly and analyze the illustrations
before proceeding to do the assembly.
• Follow the instructions step by step and do not skip any unless our Customer
Service advises it is OK to do so.|
• Make sure you understand which hardware will be used on each step. Using the
wrong size of screw, bolt or pin might strip the threads or cause damage to
the part in which it is being used.|
• To avoid misalignments, always leave the screws loose and tighten them until
all pieces are positioned correctly.|
• Do not overtighten or force the screws as they might break, strip, damage
the threads of the holes or get stuck inside the part.|
• If the hole seems too small for the screw, make sure you are using the
correct size of screw and/or that you are installing it in the correct hole.|
• Sometimes on the panels the laminate or material might be covering the hole
partially or entirely. If there is no visible
hole or it seems too small, pass and press the tip of your finger over the
area where the hole should be located to feel
its indentation, and once found, carefully pierce the laminate to uncover the
hole underneath.|
ASSEMBLY STEPS
You WIIL NOT join any panels in this step.
Insert the wooden dowels 1 into the indicated holes on panels B, C, D, E, F,
G, I, J and K as shown. Make sure to insert in the correct holes as others are
intended for other hardware in other steps.
Attach the cam bolts 5 to the indicated holes on panels A, C, D, E and H as
shown. Please make sure to insert in the correct holes as others are intended
for other hardware in other steps.
Please note that on panel E the bolts attach on both sides.
Grab all the 3 sets of sliders 7 and separate them into 2 groups according to
their shape:
The “flat” ones will be used on the next step.
The “L” shaped will be used until step 14, set them aside.
Use screws 2 to assemble the “Flat” sliders 7 to the panels D and E in their
respective sides (Left sliders to E, right sliders to D).
NOTES:
The wheels go towards the front of the panels.
Attach first on the front, through the 3rd hole on the slider.
The sliders will show 2 free holes above the wheels.
With the help of another person, attach the skirt panel I to the middle side panel E and keep holding the panel while the other person assembles the right side panel D to the panels F and G using cam locks 5 as shown and as explained in page 4.
VERY IMPORTANT – PLEASE READ THE INSTRUCTIONS FIRST
It is very important to follow this step exactly as instructed as it avoids
the wood panels from cracking or splitting in the process.
- Have ready on hand the cam locks 5 and a screwdriver (not included).
- With the help of another person, join the back panel B to panel E and keep holding the panel on the other end, or place a 3″ or 4″ thick square object (like a book) underneath to keep it horizontal.
- Then the other person will join panel C to panel B, while you install and turn the cam locks in panel B as shown and as explained in page 4.
With the help of another person, join the tabletop A to the panels B, C, D and
E.
Install the cam locks 5 into panels B, C, D and E and turn them to lock them
to the tabletop as shown and as explained in page 4.
Please note that there will be one last cam lock hidden on C pending to
install later.
- Use a hammer (not included) to install the glides 8 to the bottom of the panels C, D and E as shown.
- Cover with 6 all the cam locks on panels B, C, D and E that will become visible when the item is finished.
With the help of another person, bring the unit upright.
Install the cam lock 5 into the back hole of panel C as shown and as explained
in page 4, and cover it with 6.
Attach the corner brackets 9 to the 2 upper corners of the back panel N with
screws 3.
For each of the 3 drawers, assemble the side panels J and K to the front panel
H on their respective sides with cam locks 5 as shown and as explained in page
4.
For each of the 3 drawers, slide the bottom board M through the grooves of
panels J and K and into the groove of panel H. 
https://youtu.be/CzjxfVFbSoQ
For each of the 3 drawers, assemble the back panel L to the side panels J and K with screws 4 from the sides.
For each of the 3 drawers, install the handle 10 to the front panel H using its own screws 10, then cover the cam locks on panels J and K with 6.
- For each of the drawers, flip them upside-down and assemble the L shaped sliders 7 to the side panels J and K on the bottom with screws 11.
- NOTES:
- The wheels go towards the back of the drawer.
- The sliders should not protrude on the bottom; if they do, the drawers will raise 1″ more and won’t fit on the desk.
Insert the drawers into the unit starting with the bottom, then middle, then
top drawer. You might have to insert them at an angle facing down.
NOTES:
- If the drawers stop halfway, check and make sure that the screws inside the unit and on the drawer are properly tightened and their heads don’t protrude or interfere with the drawers’ rollers.
- If the drawers don’t seem to fit, review the assembly of the sliders in page 7 step 4, and page 14 step 14 for the correct assembly.
Give yourself a nice pat on the back, you did a great job! ENJOY YOUR NEW UNIT!
WEIGHT LIMITS
WARNINGS
- Do not exceed the indicated weight limits.
- Do not expose the surfaces to direct sunlight or to extreme environmental conditions.
- Do not use solvents or abrasive materials to clean the unit.
- Do not sit on the unit or lean against it.
- Do not allow small children to play under or over the unit.
- Do not allow small children to reach inside the drawers or compartments without your supervision.
- Do not pull, push or drag the unit to move it for more than 1 feet. The unit must be lifted by at least 2 persons when moving in the same or adjacent rooms.
- Before moving the unit, make sure to secure or remove any object that is heavy or might fall off.
- When lifting the unit, use both hands and bend your knees, not your backs.
CARE AND MAINTENANCE
- Clean the surfaces preferable with a clean cloth damped in a solution of mild soap and water, then dry with a clean towel.
- If you decide to use a cleaning agent, test first on an area hidden from view such as underneath the tabletop.
- Every 4 months, inspect the unit completely and make sure that all screws are tighten.
- When transporting the unit to places far away, protect and secure the unit to avoid damage in transit.
- Shall any part of the unit become defective during the warranty period, replacement parts might be available to you at no charge. Please refer to the last pages on this manual.
- The warranty does not extend to regular wear and tear, nor the manufacturer assumes liability for damages or consequences due to accidents, incorrect assembly, negligence, improper use, modifications, or not heeding the above warnings.
TECHNI MOBILI WARRANTY
DESKS/LAPTOP CARTS/FILE CABINETS: LIMITED 5-YEAR WARRANTY
RTA Products, LLC warrants to the Original Purchaser who acquired a new
product from RTA Products or its authorized resellers that this product will
be free from defects in its workmanship and materials, under normal use and
service conditions, as described herein. “Defects” as used in this warranty,
is defined as any imperfections that impair the use of the furniture or
product. RTA Products LLC will replace any defective part, at its discretion,
and without charge to the original purchaser other than the freight from the
end consumer to RTA Products.
Replacement parts can only be supplied if parts are available. Items out of
production may be unavailable. This warranty will be effective for the
applicable time period beginning the date of purchase on your original sales
receipt. RTA product’s obligation under this warranty is limited to repairing
or replacing products or parts as provided herein. This product has been
designed for and is intended for office and home-office use only. This
warranty is Original Purchaser’s sole remedy for product defects, and this
warranty does not extend to any product, or damage to any product, caused by
or attributed to abuse or misuse, products used for commercial or rental
purposes, use modifications of, or attachments to the product, and products or
parts not used, maintained, or extended hereunder is in lieu of any and all
other warranties, express or implied, including without limitations any
implied warranty or merchantability or of fitness for a particular purpose.
Please note, all desks made with PVC Laminate surface should not be exposed to
direct sunlight, as it may damage the material. Damage of this nature is not
covered under this warranty.
RTA Products will not be responsible for indirect, special, incidental or
consequential damages. This warranty is limited to merchandise purchased in
the Continental United States, excludes AK, HI and PR. Some States do not
allow the exclusion or limitation of incidental or consequential damages, so
the above limitations or exclusions may not apply to you. This warranty gives
you specific legal rights. You may also have other rights that may vary from
state to state.
RTA Products will advise you of the procedure to follow in making warranty
claims. The following are the procedures for warranty claims:
a. Call us Monday – Friday, from 9am-5pm (Eastern Time) at (866) 782-5520 to
explain the defect and give your name, address and phone number. Please have
ready the model number of our product, date and place of purchase. You can
also write to us by e-mail to
warranty@rtaproducts.com and include the
same information.
b. If we determine that replacement will remedy the situation, and in order to
determine the extent or the cause of the defect, purchaser will need to send
the part in question at purchaser’s expense. Once we receive the part, we will
examine it and determine whether the claim is valid (or not), and then
proceed to send the replacement. We will ship the replacement at our expense.
FOR SEVERAL HELP OPTIONS
INCLUDING REPLACEMENT PARTS ORDERS
VISIT: WWW.TECHNIMOBILI.COM
AND CLICK ON SUPPORT TAB
Or scan the following QR Code:
https://technimobili.com/pages/support
Scan the following QR Code to order replacement
parts:https://technimobili.com/pages/order-parts
EMAIL US:
support@rtaproducts.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>