TECHNI MOBILI RTA-B002 Sit to Stand Rolling Adjustable Height Laptop Cart Instruction Manual
- October 30, 2023
- TECHNI MOBILi
Table of Contents
TECHNI MOBILI RTA-B002 Sit to Stand Rolling Adjustable Height Laptop Cart
Thank you for purchasing our product.
Product Information
Model: RTA-B002
The RTA-B002 is a multi-purpose unit that can be used as a storage shelf or utility cart. The unit has a durable metal frame and features locking and non- locking casters for easy mobility. It comes with various panels, including left and right panels, back and front panels, a middle shelf, a bottom panel, and a top shelf. The unit also includes hardware, screws, and fittings necessary for assembly.
Product Usage Instructions
Before starting the assembly, please read the following tips and warnings:
- Do a quick inventory to make sure the package contains all the parts and hardware listed in the assembly instructions.
- To avoid misalignments, always leave the screws loose and tighten them until all pieces are positioned correctly.
- Missing, damaged, and defective parts can be replaced at no cost to you. Please refer to the last pages on this manual.
- The replacement parts service is limited to the 48 contiguous United States. If you reside in Alaska, Hawaii, Puerto Rico, U.S. territories or other countries, please contact the supplier from where the unit was purchased.
- If during assembly you find an issue or need clarification, please contact our Customer Service for assistance. Please refer to the last pages on this manual.
- On each step read the instructions and analyze the illustrations thoroughly before proceeding to do the assembly.
- Make sure you understand which hardware will be used on each step. Using the wrong size of screw, bolt or pin might strip the threads or cause damage to the part in which it is being used.
- Do not overtighten or force the screws as they might break, strip, damage the threads of the holes or get stuck inside the part.
- Sometimes the laminate might cover partially or entirely the hole on a panel. If there is no visible hole for the screw, pass and press the tip of your finger over the area where the hole should be located to feel the indentation, and once found, carefully pierce the laminate to reveal the hole underneath.
- If the hole seems too small for the screw, first make sure you are using the correct size of screw and that it’s been installed in the correct hole. If the hole still appears to be too small, carefully pierce the laminate to reveal the hole’s actual size.
This unit uses cam bolts and locks for assembly. Follow these steps to assemble:
- Screw the bolt into the corresponding hole on panel A.
- Join panel B to panel A. If panel B comes with the cam lock pre-installed, make sure it is aligned to receive the bolt’s head (refer to point 3). There might be a very small gap between the panels which is normal.
- Insert the cam lock on panel B making sure it goes aligned to receive the bolt’s head. The cross points towards panel A with the bolt.
- Turn the cam lock clockwise. This will lock the parts together and will close any gaps.
Refer to the main parts list and layout for reference during assembly.
- Please read carefully the assembly instructions before the installation.
- Do not discard this manual or any of the packaging material until the unit has been completely assembled.
- You can watch the complete assembly video demonstration online by scanning the QR code on the front page, as well you can watch the individual steps by scanning the QR codes shown.
MAIN PARTS LIST
MAIN PARTS LAYOUT (FOR REFERENCE)
LIST OF HARDWARE, SCREWS AND FITTINGS
This unit uses cam bolts and locks. The following explains how to use them. This is not an assembly step; it is a guide for when you are actually doing the assembly using this kind of hardware.
- CamLock
- Cam Bolt
Installation Instructions
- Screw the bolt into the corresponding hole on panel “A”.
- Join panel “B” to panel “A”. If panel “B” comes with the cam lock pre-installed, make sure it is aligned to receive the bolt’s head (refer to point 3). There might be a very small gap between the panels which is normal.
- Insert the cam lock on panel “B” making sure it goes aligned to receive the bolt’s head.
- Alignment: The cross points towards the panel “A” with the bolt.
- Turn the cam lock clockwise. This will lock the parts together and will close any gaps.
Precautions
BEFORE YOU START THE ASSEMBLY, PLEASE READ THE FOLLOWING TIPS AND WARNINGS.
- Do a quick inventory to make sure the package contains all the parts and hardware listed in the assembly instructions.
- Missing, damaged and defective parts can be replaced at no cost to you. Please refer to the last pages on this manual.
- The replacement parts service is limited to the 48 contiguous United States. If you reside in Alaska, Hawaii, Puerto Rico, U.S. territories or other countries, please contact the supplier from where the unit was purchased.
- If during assembly you find an issue or need clarification, please contact our Customer Service for assistance. Please refer to the last pages on this manual.
- On each step read the instructions and analyze the illustrations thoroughly before proceeding to do the assembly.
- Make sure you understand which hardware will be used on each step. Using the wrong size of screw, bolt or pin might strip the threads or cause damage to the part in which it is being used.
- To avoid misalignments, always leave the screws loose and tighten them until all pieces are positioned correctly.
- Do not overtighten or force the screws as they might break, strip, damage the threads of the holes or get stuck inside the part.
- Sometimes the laminate might cover partially or entirely the hole on a panel. If there is no visible hole for the screw, pass and press the tip of your finger over the area where the hole should be located to feel the indentation, and once found, carefully pierce the laminate to reveal the hole underneath.
- If the hole seems too small for the screw, first make sure you are using the correct size of screw and that it’s been installed in the correct hole. If the hole still appears to be too small, carefully pierce the laminate to reveal the hole’s actual size.
ASSEMBLY STEPS
STEP 1
- Attach bolts D into the indicated holes on the left panel 1.
- On panels 4, 5 and 6 check and make sure the cam locks on their left side are aligned to receive the bolts.
- Assemble panels 4, 5 and 6 to panel 1 and turn the cam locks to lock the panels as explained. Note: Panels 4 and 6 do not assemble one another, they just lay flushed.
STEP 2
- Screw bolts D into the corresponding holes on the right panel 2, then align cam locks on panels 4, 5, 6 and finally assemble panel 2 to those panels and turn the cam locks as explained.
STEP 3
Use screws A to assemble the casters 3 to panel 7 to its bottom surface the following way:
- Locking casters 3L go at the front of the panel.
- Non-Locking casters 3N go at the back of the panel.
STEP 4
- Assemble panels 1, 2 and 4 (from step 2) to the top surface of panel 7 with bolts D as explained.
- Please make sure to identify the correct holes where D will be installed on the bottom panel.
STEP 5
- Assemble the top shelf 8 to panels 1, 2 and 4 with bolts D as explained.
STEP 6
- Assemble the stationary tubes 9 to the side panels 1 and 2 with screws C from the sides and to the bottom panel 7 from the bottom.
STEP 7
- Place the plastic covers 11A over tubes 9 with the threaded holes facing toward the outside.
STEP 8
- Insert the adjustable “T” tube 10 through the covers 11A and into the tube 9 making sure the longer end of the square tube faces towards the front.
- Lift the tubes at least 7 inches(about an open bandwidth) and insert and tighten the screw knobs 11B into the covers 11A.
- Both tubs should be lifted at the same height to beable to do the next step properly.
STEP 9
- Assemble the main panel 12 to the tubes 10 with screws C from underneath.
STEP 10
- Assemble the protection tube 13 to the main panel 12 with screws B from underneath.
STEP 11
- Adjust the height of the main panel by loosening the screw knobs 11B and re-tighten when the desired height is reached.
ALL DONE
- Give yourself a nice pat on the back. You did a great job!
CARE AND MAINTENANCE
CARE, MAINTENANCE AND SAFETY WARNINGS
WEIGHT LIMITS
- Do not exceed the indicated weight limits.
- Because the lift and lock system on this unit consists of friction of metals, frequent adjustments of the tabletop’s height might cause scuffs on the paint on the metal tubes.
- This consequence is not considered a defect, and even with the scuffs the unit should still be able to function properly as intended.
- Do not over-tighten the screw knobs. Please note that frequent height adjustments and over-tightening may cause the square covers to break, and such damage is not covered by the product’s warranty.
- Do not expose the surfaces to direct sunlight or to extreme environmental conditions.
- Clean the surfaces preferably with a clean cloth damped in a solution of mild soap and water, then dry with a clean towel.
- Do not use solvents or abrasive materials to clean the unit.
- If you decide to use a cleaning agent, test first on an area hidden from view such as underneath the tabletop.
- Do not climb on the base of the unit or use it as a moving vehicle.
- Before moving the unit, make sure to unlock the front casters.
- When moving the unit, make sure to secure any object that might fall off.
- When transporting the unit to places far away, protect and secure the unit to avoid damage in transit.
- Shall any part of the unit become defective during the warranty period, replacement parts might be available to you at no charge. Please refer to the last pages on this manual.
- The warranty does not extend to regular wear and tear, nor the manufacturer assumes liability for damages or consequences due to accidents, incorrect assembly, negligence, improper use, modifications, or not heeding the above warnings.
TECHNI MOBILI DESK WARRANTY
DESKS/LAPTOP CARTS/FILE CABINETS: LIMITED 5-YEAR WARRANTY
RTA Products, LLC warrants to the Original Purchaser who acquired a new product from RTA Products or its authorized resellers that this product will be free from defects in its workmanship and materials, under normal use and service conditions, as described herein. “Defects” as used in this warranty, is defined as any imperfections that impair the use of the furniture or product. RTA Products LLC will replace any defective part, at its discretion, and without charge to the original purchaser other than the freight from the end consumer to RTA Products.
Replacement parts can only be supplied if parts are available. Items out of production may be unavailable. This warranty will be effective for the applicable time period beginning the date of purchase on your original sales receipt. RTA product’s obligation under this warranty is limited to repairing or replacing products or parts as provided herein. This product has been designed for and is intended for office and home-office use only. This warranty is Original Purchaser’s sole remedy for product defects, and this warranty does not extend to any product, or damage to any product, caused by or attributed to abuse or misuse, products used for commercial or rental purposes, use modifications of, or attachments to the product, and products or parts not used, maintained, or extended hereunder is in lieu of any and all other warranties, express or implied, including without limitations any implied warranty or merchantability or of fitness for a particular purpose. Please note, all desks made with PVC Laminate surface should not be exposed to direct sunlight, as it may damage the material. Damage of this nature is not covered under this warranty. RTA Products will not be responsible for indirect, special, incidental or consequential damages. This warranty is limited to merchandise purchased in the Continental United States, excludes AK, HI and PR. Some States do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights. You may also have other rights that may vary from state to state.
RTA Products will advise you of the procedure to follow in making warranty claims. The following are the procedures for warranty claims:
- Call us Monday –Friday, from 9am-5pm (Eastern Time) at (866) 782-5520 to explain the defect and give your name, address and phone number. Please have ready the model number of our product, date and place of purchase. You can also write to us by e-mailto warranty@rtaproducts.comand include the same information.
- If we determine that replacement will remedy the situation, and in order to determine the extent or the cause of the defect, the purchaser will need to send the part in question at purchaser’s expense. Once we receive the part, we will examine it and determine whether the claim is valid (or not), and then proceed to send the replacement. We will ship the replacement at our expense.
FOR SEVERAL HELP OPTIONS
INCLUDING REPLACEMENT PARTS ORDERS
VISIT: WWW.TECHNIMOBILI.COM
CLICK ON SUPPORT TAB
Scan QR Code to order replacement parts
OR EMAIL US: SUPPORT@RTAPRODUCTS.COM
Scan QR Code to view full assembly video
Documents / Resources
|
TECHNI MOBILI RTA-B002 Sit to Stand Rolling Adjustable Height Laptop
Cart
[pdf] Instruction Manual
RTA-B002 Sit to Stand Rolling Adjustable Height Laptop Cart, RTA-B002, Sit to
Stand Rolling Adjustable Height Laptop Cart, Adjustable Height Laptop Cart,
Height Laptop Cart, Laptop Cart
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>