TECHNI MOBILI RTA-980FBC Modern Industrial Walnut Floating Shelves 2 Tier Wall Mount Shelf Instruction Manual

June 15, 2024
TECHNI MOBILi

MODEL RTA-980FBC
ASSEMBLY INSTRUCTIONS
Thank you for purchasing our product.

REV-CAR-6643-0622-0

RTA-980FBC Modern Industrial Walnut Floating Shelves 2 Tier Wall Mount

Shelf

| Please read carefully the assembly instructions before the installation.
---|---
| Do not discard this manual or any of the packaging material until the unit has been  completely assembled.
| Might require two people.

MAIN PARTS LIST

TECHNI MOBILI RTA 980FBC Modern Industrial Walnut Floating Shelves - MAIN
PARTS LIST 1

MAIN PARTS LAYOUT (FOR REFERENCE)

TECHNI MOBILI RTA 980FBC Modern Industrial Walnut Floating Shelves - MAIN
PARTS LAYOUT 1

LIST OF INCLUDED HARDWARE

TOOLS YOU WILL NEED (NOT INCLUDED)

NOTE: You will need screwdriver, hammer, pencil, leveler, measuring tape and drilling machine (not included) to assemble the products.

BEFORE YOU START THE ASSEMBLY

PLEASE READ THE FOLLOWING TIPS AND WARNINGS.

Do a quick inventory to make sure the  package contains all the parts and
hardware listed in the assembly instructions.| | Make sure you understand which hardware will be used on each step. Using the wrong size of screw, bolt or pin might strip the
threads or cause damage to the part in which it is being used.|
---|---|---|---
Missing, damaged and defective parts can be replaced at no cost to you. Please refer to the last pages on this
manual.| | To avoid misalignments, always leave the screws loose and tighten them until all pieces are positioned correctly.|
The replacement parts service is limited to the 48 contiguous United States.
If you reside in Alaska, Hawaii, Puerto Rico, U.S. territories or other countries, please contact the supplier from where the unit was purchased.| | Do not overtighten or force the screws as
they might break, strip, damage the threads of the holes or get stuck inside the part.|
If during assembly you find an issue or
need clarification, please contact our Customer Service for assistance.
Please refer to the last pages on this manual.| | Sometimes the laminate might cover
partially or entirely the hole on a panel. If there is no visible hole for the screw, pass and press the tip of your finger over the area where the hole should be located to feel the indentation, and once found, carefully pierce the laminate to reveal the hole underneath.|
On each step read the instructions and analyze the illustrations thoroughly
before proceeding to do the assembly.| | If the hole seems too small for the screw,
first make sure you are using the correct size of screw and that it’s been installed in the correct hole. If the hole still appears to be too small, carefully pierce the laminate to reveal the hole’s actual size.| TECHNI
MOBILI RTA 980FBC Modern Industrial Walnut Floating Shelves - BEFORE YOU START
THE ASSEMBLY 10

ASSEMBLY STEPS

STEP 1
Place one of the shelves 1 over the brackets of the metallic supports 2.
The surface with the pre-drilled holes go facing down and they should align with the brackets.

TECHNI MOBILI RTA 980FBC Modern Industrial Walnut Floating Shelves -
ASSEMBLY STEPS 1

STEP 2
Hardware/Tools

Use a screwdriver (not included) to secure the shelf 1 to the supports 2 with screws A as shown.

TECHNI MOBILI RTA 980FBC Modern Industrial Walnut Floating Shelves -
ASSEMBLY STEPS 3

STEP 3
Place the second shelf 1 over the brackets of the metallic supports 2.
The surface with the pre-drilled holes go facing down and they should align with the brackets.

TECHNI MOBILI RTA 980FBC Modern Industrial Walnut Floating Shelves -
ASSEMBLY STEPS 4

STEP 4
Hardware/Tools

Use a screwdriver (not included) to secure the shelf 1 to the supports 2 with screws A as shown.

TECHNI MOBILI RTA 980FBC Modern Industrial Walnut Floating Shelves -
ASSEMBLY STEPS 6

Tip
If desired, after assembly use an alcohol cleaner to erase the number printed on the parts.

STEP 5
Hardware/Tools
IMPORTANT:
The measurements given here should make the holes on the wall coincide with the holes on the metallic supports, however, there is always a small chance that they  might not exactly coincide by mere millimeters. You should always check and compare the measurements on the supports against the markings on the wall before drilling any holes.

  • Select the height you want to fix the product on your wall.
  • Use a pencil (not included) to mark on the wall where it would be the bottom left hole.
  • From this marking, use a measuring tape and a lever (not included) to find and mark the left top hole. We recommend measuring in millimeters for better accuracy.
  • In the same manner, find and mark on the wall the right top and right bottom holes.
  • Verify that the markings on the wall coincide with the holes on the unit.
  • Once the markings are verified, use a power driller with Ø6mm drill bit (not included) to make the 4 holes on the wall.
  • After drilling the holes, use a hammer (not included) to insert the anchors.

TECHNI MOBILI RTA 980FBC Modern Industrial Walnut Floating Shelves -
ASSEMBLY STEPS 9

STEP 6
Hardware/Tools

TECHNI MOBILI RTA 980FBC Modern Industrial Walnut Floating Shelves -
ASSEMBLY STEPS 11

ALL DONE!
Give yourself a nice pat on the back. You did a great job!

TECHNI MOBILI RTA 980FBC Modern Industrial Walnut Floating Shelves -
ASSEMBLY STEPS 12

CARE, MAINTENANCE AND SAFETY WARNINGS:

WEIGHT LIMITS

= 11 Lbs. (5 Kg )

  • Do not exceed the indicated weight limits.
  • Do not expose the surfaces to direct sunlight or to extreme environmental conditions.
  • Clean the surfaces preferable with a clean cloth damped in a solution of mild soap and water, then dry with a clean towel.
  • Do not use solvents or abrasive materials to clean the unit.
  • If you decide to use a cleaning agent, test first on an area hidden from view such as underneath the tabletop.
  • Do not allow small children to play under or over the unit.
  • Do not allow small children reaching onto the shelves by themselves, as objects might fall and hurt them.
  • Always get another person to help you when removing and re-locating the unit somewhere else.
  • Shall any part of the unit become defective during the warranty period, replacement parts might be available to you at no charge. Please refer to the last pages on this manual.
  • The warranty does not extend to regular wear and tear, nor the manufacturer assumes liability for damages or consequences due to accidents, incorrect assembly, negligence, improper use, modifications, overloading, or not heeding the above warnings.

TECHNI MOBILI DESK WARRANTY

DESKS/LAPTOP CARTS/FILE CABINETS: LIMITED 5-YEAR WARRANTY
RTA Products, LLC warrants to the Original Purchaser who acquired a new product from RTA Products or its authorized resellers that this product will be free from defects in its workmanship and materials, under normal use and service conditions, as described herein. “Defects” as used in this warranty, is defined as any imperfections that impair the use of  the furniture or product. RTA Products LLC will replace any defective part, at its discretion, and without charge to the original purchaser other than the freight from the end consumer to RTA Products.
Replacement parts can only be supplied if parts are available. Items out of production may be unavailable. This warranty will be effective for the applicable time period beginning the date of purchase on your original sales receipt. RTA product’s obligation under this warranty is limited to repairing or replacing products or parts as provided herein. This product has been designed for and is intended for office and home-office use only. This warranty is Original Purchaser’s sole remedy for product defects, and this warranty does not extend to any product, or damage to any product, caused by or attributed to abuse or misuse, products used for commercial or rental purposes, use modifications of, or attachments to the product, and products or parts not used, maintained, or extended hereunder is in lieu of any and all other warranties, express or implied, including without limitations any implied warranty or
merchantability or of fitness for a particular purpose. Please note, all desks made with PVC Laminate surface should not be exposed to direct sunlight, as it may damage the material.
Damage of this nature is not covered under this warranty.
RTA Products will not be responsible for indirect, special, incidental or consequential damages. This warranty is limited to merchandise purchased in the Continental United States, excludes AK, HI and PR. Some States do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights. You may also have other rights that may vary from state to state.
RTA Products will advise you of the procedure to follow in making warranty claims. The following are the procedures for warranty claims:
a. Call us Monday –F riday, from 9am-5pm (Eastern Time) at 866-782-5520 to explain the defect and give your name, address and phone number. Please have ready the model number of our product, date and place of purchase. You can also write to us by e-mail to warranty@rtaproducts.com and include the same information.
b. If we determine that replacement will remed tyhe situation, and in order to determine the extent or the cause of the defect, purchaser will need to send the part in question at purchaser’s expense. Once we receive the part, we will examine it and determine whether the claim is valid (or not), and then proceed to send the replacement. We will ship the replacement at our expense.

FOR SEVERAL HELP OPTIONS
INCLUDING REPLACEMENT PARTS ORDERS
VISIT: WWW.TECHNIMOBILI.COM
 CLICK ON SUPPORT TAB
https://technimobili.com/pages/order-parts
Scan QR Code to order replacement parts
OR EMAIL US: SUPPORT@RTAPRODUCTS.COM

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

TECHNI MOBILi User Manuals

Related Manuals