EDM 70421 6000K Cold Light With Sensor Frameless Instruction Manual

EDM 70421 6000K Cold Light With Sensor Frameless

INSTRUCTION

Read this manual carefully before using the device and save it for future reference. To reduce the possible risk of fire, electric shock or personal injury, keep in mind the following instructions:

GENERAL INFORMATION

• The lamps may only be installed by authorized and qualified technicians according to the valid regulations for electrical installation.
• Before operating this appliance, read the following instructions. Keep the manual in a safe place so you can consult it at any time.
• After removing the packaging, check that the appliance is in good condition, and if you have any questions, do not turn it on.
• Contact your distributor or seller for the return of the appliance.
• This device is packed for protection against any damage or damage that may be caused by transportation.
• The packaging is made up of plastics and other materials that can be dangerous. Keep out of reach of children. These materials are recyclable and must be delivered in a unit of the appropriate recycling, respecting the environmental laws.
• This appliance has been designed for DOMESTIC USE only and must not be used with any other appliance, such as for example in a commercial, industrial or any other non-residential installation.
• Do not handle the appliance with wet hands and do not immerse it in water or any other liquid.
• Unplug the appliance from the mains before cleaning it.
• This device is not intended to be used by people (including children) with reduced physical capacities, sensory or mental, or lack of experience and knowledge unless they have received instructions regarding use of the device or are accompanied by a responsible person.
• Keep the device out of the reach of children under 8 years.
• Children should be supervised during use, to make sure they do not play with the appliance.
• Do not continue using the appliance if you notice that it is not working properly. Turn it off immediately and look for the manufacturer or an authorized technical service so that a qualified technician can evaluate the damage and repair it if necessary.
• If the power cord is damaged, it must be replaced by the manufacturer or by a qualified technician to avoid the risk of electric shock.
• Turn off the appliance and disconnect the power cord from the power outlet before replacing any part or accessory, or before touching the moving parts of the device.

IMPORTANT SAFETY INSTRUCTIONS

• Connect the device only to an AC power source. The voltage indicated on the rating plate that is on the device, must match the voltage of the power supply.
• Always disconnect the appliance from the socket after use, to disassemble or clean it.
• Always mount and use the appliance on a stable and secure surface.
• Never place the appliance on or near heat sources, such as a gas /electric stove or inside a hot oven. Keep the power cord away from these sources of heat or sharp objects.
• Never handle the power cord with wet hands.
• The use of accessories or parts not recommended by the manufacturer may cause a fire, an electric shock or serious injuries.
• This device is manufactured to be used indoors. Never use it outdoors or in outside parts of the house.

ICONS

1. 1. Protection class I: the fitting has an earthing connection. The earth wire (yellow/green) has to be connected to the clip marked with.
2. Protection class II: the fitting is double insulated and must not be connected to an Earth.
3. Protection class III: the fitting is only suitable for very low voltage supply (e.g.12V)
4. The fitting is suitable for fixing to normal flammable surfaces.
5. The light must not be covered with insulating thermal material.
6. Light not suitable for direct mounting on normally inflammable surfaces (suitable only for non-combustible surfaces).
7. Always observe the minimum distance between the lamp and the lit objects as indicated in the icon.
8. The IP is the grade of protection that the surround of the light offers against dust, sold bodies and damp.
9. Immediately replace a cracked or broken safety glass and use only manufacturer approved parts.
10. The fitting is only suitable for energy saver lamps.
11. Capsule and linear halogen lamps may not be touched by bare hands.
12. Light designed to use only halogen lamps of wolfram or metallic halogen lamps with their own protective screen.
13. The fitting is working with a safety transformer. Replace a broken transformer only by a transformer with identical technical specifications. Consult a qualified electrician or your retail outlet.
14. Luminary is suitable for use in interior with an ambient temperature of __ºC.
15. The connection between the base of the socket and the plug of the lamp must be in accordance with the degree of protection against dust and moisture from the Luminary.
16. Don’t put wires over the luminary.
17. This luminaire contains in some places very hot parts.
18. This luminaire is a replaceable source.

IP FIGURES

The first digit (IP ) indicates the protection from solid objects. 0: Non protected

1. Protected against solid objects Ø ≥ 50mm
2. Protected against solid objects Ø ≥ 12mm
3. Protected against solid objects Ø ≥ 2,5mm
4. Protected against solid objects Ø ≥ 1mm
5. Dust protected
6. Dust tight

The second digit (IP ) indicates protection from moisture. 0: Non protected

1. Protected against dripping water
2. Protected against dripping water when tilted up to 15º
3. Protected against dripping water when tilted up to 15º
4. Protected against splashing water
5. Protected against water jets
6. Protected against heavy seas
7. Protected against the effects of immersion
8. Protected against submersion

FEATURES

This product contains a light source of energy efficiency class: F

INSTALLATION

Prior to Installation:
Please pay attention to the following points:

• Do not fix the sensor too high, resulting in a too-large range coverage, which would be followed by an unwanted turning on and off. The best results are shown within the 1.8 to 2.3M height range.
• The range coverage is influenced by the temperature. It can be bigger in winter than in summer.
• Don’t install the sensor near trees and bushes. The movement of the plants can result in unwanted turning on and off.
• The sensor is more sensitive to sideway movements than forward and backward movements.

Installation may only be carried out by trained professionals according to the applicable installation regulations. Contact a licensed electrician.

ATTENTION!

MAINTENANCE AND CLEANING

• The light must be disconnected and cold before cleaning.
• The light must be cleaned with a soft, damp cloth, preventing the electrical parts from coming into contact with liquids. Do not use dissolvents or abrasive substances. Use normal neutral PH detergent.

WASTE
This symbol on the product or in the instructions means that your electri-cal and electronic equipment must be disposed at the end of its useful life in a specialized container; Do not dispose it in the usual household waste container. In the EU there is special waste collection systems for subse-quent recycling. For more information, contact with the local authority or the retailer from whom you purchased the product.

WARRANTY
All our products are subject to the legal warranty in force at all times regarding consumption and cover all manufacturer’s failures regarding material and quality. This warranty applies only if the instructions for use have been followed, and it is voided if the device has been forced or used improperly, or if it has been repaired by an unauthorized person.

THE INVOICE IS THE PRODUCT WARRANTY
THE MANUFACTURER DECLINES ALL RESPONSIBILITY DUE TO AN INCORRECT INSTALLATION OF THE APPLIANCE.

IMPORTED BY
www.edmproduct.com ELEKTRO3, S.COOP.C.L F-43389675

MADE IN CHINA

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>