EDM PRODUCT 08791 Submergible Water Pump Instruction Manual

EDM PRODUCT 08791 Submergible Water Pump

Product Information

Specifications

• Product Name: Submersible Water Pump
• Model Numbers : Ref. 08790, Ref. 08791

Product Usage Instructions

1. Safety Precautions
   Before using the submersible water pump, please read and follow all safety instructions and warnings provided in the user manual.

2. Operating Conditions
   Ensure the following conditions are met before using the product

   • Do not use the water pump in temperatures below freezing.
   • Do not operate the water pump if there are people or animals in the water.

3. Compliance
   The submersible water pump complies with relevant European regulations for health and safety. It meets the fundamental requirements of applicable EU regulations and has been tested accordingly.

4. Maintenance and Troubleshooting
   If any functionality issues occur and cannot be resolved, please contact your distributor for assistance.

5. Modifications and Unauthorized Changes
   Any modifications or unauthorized changes to the device may affect its performance and safety. Follow the manufacturer’s instructions and legal regulations to ensure safe usage.

6. Cleaning and Maintenance
   Only clean and maintain the device as instructed in the user manual. If any parts are defective, they should be replaced by the manufacturer, their customer service, or equally qualified personnel to avoid hazards.

Safety Precautions during Use
Follow these safety precautions while using the submersible water pump

• Avoid sharp edges and rough surfaces that may damage the device.
• Do not expose the device to extreme weather conditions without proper protection.
• Always fully unwind the cable before use and check if it is in good condition.
• When not in use or during maintenance, unplug the device from the power outlet.

Grounding and Electrical Safety
For electrical safety, ensure the following

• The grounding, neutral conductor, and RCD (Residual Current Device) should be functioning correctly and comply with national standards.
• Consult an expert if unsure about electrical connections or grounding requirements.

Intended Use
The submersible water pump is designed for draining transporting, and lifting the following media

• Clean water
• Wastewater
• Bilge water
• Brine
• Sandy water
• Food
• Cleaning agents
• Fuels (e.g., gasoline, diesel)
• Oils
• Greases
• Nitrocellulose thinner
• Wastewater from sinks and urinals

Frequently Asked Questions (FAQ)

1. Q: What should I do if the water pump malfunctions?
   A: If any functionality issues occur, first refer to the troubleshooting section in the user manual. If the issue persists, contact your distributor for assistance.

2. Q: Can I use the water pump in freezing temperatures?
   A: No, it is not recommended to use the water pump in temperatures below freezing.

3. Q: Can I make unauthorized modifications to the device?
   A: No, unauthorized modifications or changes to the device may affect its performance and safety. Follow the manufacturer’s instructions and legal regulations to ensure safe usage.

4. Q: How should I clean and maintain the water pump?
   A: Only clean and maintain the water pump as instructed in the user manual. If any parts are defective, they should be replaced by the manufacturer, their customer service, or equally qualified personnel to avoid hazards.

READ THIS ENTIRE INSTRUCTION LEAFLET CAREFULLY. IT CONTAINS IMPORTANT INFORMATION IN RELATION TO THE USE OF YOUR PUMP AND PRECAUTIONARY MEASURES THAT MAY NEED TO BE TAKEN. READING THESE INSTRUC-TIONS THOROUGHLY WILL ENSURE YOU GET THE VERY BEST PERFORMANCE FROM THE PRODUCT AND ENSURE MAXIMUM SAFETY. ANY USE, OTHER THAN SET OUT IN THIS LEAFLET, COULD CAUSE DAMAGE, INJURY AND REPRESENT A HAZARD; IT WILL ALSO INVALIDATE THE GUARANTEE. KEEP THIS BOOKLET IN A SAFE PLACE FOR REFERENCE.

NOTES REGARDING THE OPERATING MANUAL SYMBOLS

• The illustrations in this operating manual feature the device by way of example.
  Some using or operation functions are similar or the same, but some appearance details willbe different from the real device!

SYMBOLS ON THE DEVICE

• Warning of electrical voltage
  This symbol indicates dangers to the life and health of people due to electrical voltage.

• Warning
  This signal word indicates a hazard with an average risk level which, if not avoided, can result in serious injury or death.

• Caution
  This signal word indicates a hazard with a low risk level which, if not avoided, can result in minor or moderate injury.
  Notice
  This signal word indicates important information (e.g. material damage), but does not indicate hazards.

• Info
  Information marked with this symbol helps you to carry out your tasks quickly and safely.

• **Follow the manual**
  Information marked with this symbol indicates that the operating manual must be observed.
  Do not use damaged power cables or mains plugs

• Staying in water prohibited
  This symbol indicates that the device must not be operated with persons or animals in the water.

• Do not use at freezing temperatures
  This symbol indicates that the device must be protected from frost.
  Keep out of the reach of children (is not a toy)
  This symbol indicates that the device is not a toy and is thus not suitable for children.

• Do not pull the mains plug by the power cable
  This symbol indicates that you must not pull the mains plug out of the socket by the power cable.

• Pull the mains plug
  This symbol indicates that the mains plug must be removed from the socket when the device is not in use.

• Not suitable for pumping potable water
  This symbol indicates that the device is not suitable for pumping potable water.

• Submerge pump at a slight angle
  This symbol indicates that the pump must be submerged into the water at a slight angle to allow the remaining air to escape.

• Complies with relevant European regulations

WARRANTY AND LIABILITY

The device complies with the fundamental health and safety requirements of the applicable EU regulations and was tested at the factory for perfect functionality multiple times.
However, if faults in the functionality occur and cannot be remedied with the measures in the chapter Errors and faults, please get in touch with your dealer or distributor.
When making a warranty claim, supply the device number (see label on the device).
When manufacturer’s instructions or legal regulations have not been followed, or after unauthorized changes to the device are made, the manufacturer is not responsible for the resulting damages. Changes to the device or unauthorised replacement of individual parts can drastically impact the electrical safety of this product and will result in the loss of the warranty. Liability does not extend to damages to people or property caused by the device being used other than as described in the instructions in this operating manual. Subject to changes to technical design and model changes as part of constant development and product improvement without prior notice.
No liability is accepted for damages resulting from improper use. In such a case, any warranty claims will be voided also.
ALWAYS KEEP THE MANUAL IN A NEARBY PLACE!

Warning

• Read all safety warnings and all instructions.
• Failure to follow the warnings and instructions may result in electric shock, fire and / or serious injury.
• Save all warnings and instructions for future reference. This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

General safety

• Do not use the device in potentially explosive rooms.
• Do not use the device in aggressive atmosphere.
• Check accessories and connection parts for possible damage prior to every use of the device. Do not use any defective devices or device parts.
• Before carrying out maintenance, care or repair work on the device, remove the mains plug from the mains socket. Hold onto the mains plug while doing so.
• When positioning the device, observe the minimum distances from walls and other objects as well as the storage and operating conditions specified in the Technical data chapter.

General safety warnings – Electrical safety

• The device is to be supplied with a rated residual current of no more than 30mA by means of an RCD (Residual Current protective Device).
• Ensure that all electric cables outside of the device are protected from damage (e.g. caused by animals). Never use the device if electric cables or the power connection are damaged!
• The electrical connection must correspond to the specifica-tions in chapter Technical data.
• Insert the mains plug into a properly secured mains socket.
• Switch the device off and disconnect the power cable from the mains socket when the device is not in use.
• Do not under any circumstances use the device if you detect damages on the mains plug or power cable.
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
• Defective power cables pose a serious health risk!
• Should the connection line of the device be damaged, it must be replaced by the manufacturer, his customer service or similarly qualified personnel in order to avoid hazards.
• Should there be a risk of flooding, install the plug connec-tions in a flood-proof area. There is a risk of electric shock!
• Make sure that the mains voltage corresponds to the specifications on the nameplate.
• Have all electrical installations carried out by an expert according to the national regulations and the device-specific requirements.
• Do not use the power cable to drag the device.
• Hold onto the mains plug while pulling the power cable out of the mains socket.
• Protect the power supply cable against heat, oil and sharp edges.
• Only use splash-proof extension cables intended for outdoor use whilst observing the device’s power input. Before using cable drums, always unroll the cable completely. Check the cable for damage.
• Before performing any work on the device, in case of leaks in the water system, before taking work breaks or when not in use, remove the mains plug from the mains socket.

General safety warnings

Personal safety

• Never use the device with persons or animals in the water or pumping medium or if they could access it. There is a risk of electric shock!
• Never insert any objects or limbs into the device.
• This appliance is not a toy! Keep away from children and animals. Do not leave the device unattended during operation.

Device-specific safety warnings for submerged pumps

• Do not leave the device running unattended to ensure an early detection of when the device runs dry or switches off automatically. This would damage the device. Regularly check the float for proper functioning.
• Please bear in mind, that the device is not suitable for conti-nuous operation (e.g. for watercourses in garden ponds). Check the device for proper functioning on a regular basis.
• Keep in mind, that lubricants are used within the device. These might potentially cause damages or contaminations if emitted. Do not use the device for drinking water or in garden ponds with either a fish population or valuable plants.
• The device is not to be carried by holding it at the power supply cable or hose. Do not fasten it there either.
• Do not place any objects on the device – not even to weight it down. The device will sink to the ground due to its own weight.
• After the set-up of the device, its mains plug must be readily accessible during operation.
• Wear sturdy shoes to protect yourself against electric shock.
•  Before taking the device into operation, have the following checked by an expert:
  •  earthing, neutral conductor and RCD must be functioning properly and correspond to the national regulations,
  • electrical plug connections must be protected from moisture.
• Provide appropriate frost protection.

INTENDED USE

The device is only suited for draining, conveying and pumping over the following media

• clear water
• non-corrosive suds (e.g. leaking washing machine)

When doing so, the water must not contain any suspended matter exceeding a maximum particle size of 5mm.The device is fully submersible (watertight encapsulation) and can be immersed up to 7m into the conveyed medium.

• The water temperature must not exceed 35°C.
• The device may temporarily be used for e.g.:
• pumping out flooded basements
• emptying tanks and containers
• the water withdrawal from wells and shafts

IMPROPER USE

• The device is not suitable for continuous operation (e.g. as recircu-lation pump for ponds).
• Using the device in swimming pools and the like is prohibited.
• The device is not suitable as permanent, automatic overflow protection of e.g. wells or fountains or for the regulation of the groundwater level. Use a stationary waste water pumping system for building and property drainage for these purposes.
• The device is not suitable for increasing the pressure of existing water supply networks.
• The device is not suitable for pumping potable water.
• The device must not be used for aggressive, abrasive, caustic, com-bustible or explosive pumping media, e.g.:
  • brine
  • sandy water
  • food
  • cleaning agents
  • fuels (e.g. petrol, diesel)
  • oils
  • greases
  • petroleum
  • nitro-cellulose thinner
  • waste water from lavatories and urinal installations
• The device must not be used at freezing temperatures.
• Any unauthorized modifications, alterations or structural changes to the device are forbidden.
• Any operation other than as described in this manual is prohibited.
• Non-observance renders all claims for liability and guarantee null and void

Personnel qualifications. People who use this device must

• Be aware of the dangers that occur when working with electric devices in damp areas.
• Have read and understood the operating manual, especially the Safety chapter.

RESIDUAL RISKS

• Warning of electrical voltage
  Work on the electrical components must only be carried out by an authorised specialist company!

• Warning of electrical voltage
  Before any work on the device, remove the mains plug from the mains socket!
  Hold onto the mains plug while pulling the power cable out of the mains socket

• Warning
  Dangers can occur at the device when it is used by untrained people in an unprofessional or improper way! Observe the personnel qualifications!.

• Warning
  The device is not a toy and does not belong in the hands of children.

• Warning
  Risk of suffocation!
  Do not leave the packaging lying around. Children may use it as a dangerous toy.

Note

• If you store or transport the device improperly, the device may be damaged.
• Note the information regarding transport and storage of the device.

BEHAVIOUR IN THE EVENT OF AN EMERGEN

1. In an emergency, disconnect the device from the mains feed-in: Switch the device off and disconnect the power cable from the mains socket. Hold onto the mains plug while doing so.
2. Do not reconnect a defective device to the mains.

OVERHEATING PROTECTION

• * The device is provided with a thermal protection circuit which is activated by overheating of the device and then switches the device off. Allow the device to cool down and switch it off. Investigate the cause of overheating. Should the problem persist, please contact the customer service.

INFORMATION ABOUT THE DEVICE

• Device description
  • The submerged water pump is only suited for draining, conveying and pumping over clear water with the contained suspended matter not exceeding a maximum particle size of 5mm.
  • A float ensures the automatic switch-on and switch-off at a respecti-vely defined height.
  • Additionally, the switch-on/-off height can be finely adjusted within the specified range by means of a locking device, see technical data. The water temperature must not exceed 35°C.

DEVICE DESCRIPTION
Designation (see fig. 1, fig. 2,fig. 3, fig. 4)

1. Transport handle / attachment for nylon cord
2. Power cable
3. Float switch locking device
4. Float switch
5. Air intake opening with cover panel and impeller
6. Connection with 1 ½” internal thread
7. Reducer
8. Elbow
9. Adapter

TECHNICAL DATA

• H05RN-3G
• 0.75mm2 *10 m

|

• H05RN-3G
• 1.0mm2 *10 m

Protection class| I| I
Weight approx.| 3.6 kg| 4.6 kg
Dimensions (length x width x height)| 170x158x300mm| 170x158x300mm
Max. particle size| 5mm| 5mm
Height for switch-on| 500mm| 500mm
Height for switch-off| 250mm| 250mm
Hose connection, inner diameter| 25mm; 32mm| 25mm; 32mm
Threaded connection| 1″; 1 ½”| 1″; 1 ½”

TRANSPORT AND STORAGE

Notice

• If you store or transport the device improperly, the device may be damaged.
• Note the information regarding transport and storage of the device.

Transport
Before transporting the device, observe the following:

• Hold onto the mains plug while pulling the power cable out of the mains socket.
• Do not use the power cable to drag the device.

Storage
When the device is not being used, observe the following storage conditions:

• Dry and protected from frost and heat
• In an upright position where it is protected from dust and direct sunlight
• With a cover to protect it from invasive dust if necessary
• Place no further devices or objects on top of the device to prevent it from being damaged.
• If you do not use the device for an extended period of time, it must be cleaned thoroughly after its last application and before recom-missioning. Deposits and residues could lead to start-up difficulties.

ASSEMBLY AND INSTALLATION

Scope of delivery

• 1 x submerged clean water pump
• 1 x reducer for inner diameters 25mm and 32mm as well as for

1” internal threads

• 1 x elbow
• 1 x manual

Unpacking the device

• Open the cardboard box and take the device out.
• Completely remove the packaging.
• Fully unwind the power cable. Make sure that the power cable is not damaged and that you do not damage it during unwinding.

START-UP
Connecting the pipe or hose line
The device may be operated using either a hose line or a pipe. Ex factory, the device is delivered
with a 1 ½” internal thread.Please observe the following information regarding the water discharge:

• Please note that making use of the reducer (7) might decrease the device performance. The reducer  (7) should be shortened to the used diameter so as not to decrease the device performance unnecessarily.
• Please note that the device cannot be moved as flexibly when using a solid pipe.
• Please note that the maximum particle size is to be reduced in proportion to the hose or pipe diameter.
• Please note that the conveying capacity declines with an increasing length of the water discharge line.

HOSE LINE

• If required, you can cut the reducer (7) off at the desired diameter.

1.  Screw the elbow (8) or adapter (9) onto the connection with 1 ½” internal thread (6).
2.  Screw the reducer (7) onto the elbow (8) or adapter (9). (see fig. 5)
3. When using a hose without thread: slide an appropriate hose clamp onto the hose.
4. Push the hose (inner diameter 25mm or 32mm) onto the reducer (7) all the way to the stop. (see fig. 6)
5. Affix the hose by means of the hose clamp.
6. When using a hose with internal thread (1”): screw the hose connection onto the reducer 7. (see fig. 7)
7. Alternatively, you can also screw a hose with Internal threading (1 ½”) directly onto the elbow (8) or adapter (9).

PIPE

• If possible, screw the pipe directly into the connection with 1  ½”  internal thread (6) or use a suitable adapter. (see fig. 8)

Adjusting the float switch

• The device comes equipped with a float switch (4) which switches the device on or off automatically according to the water level. Check the float switch (4) for proper functioning at regular intervals.

The pumping height can be regulated by means of the float switch  (4) and its position in the float switch locking device (3).
Please observe the following information regarding the float switch (4):

• Make sure that the float switch (4) always has enough clearance and is not permanently activated. This could prevent the automatic switch-off causing the device to run dry. This would damage the pump.
• Make sure that the float switch (4) is able to move freely and does not suffer from a limited mobility caused by obstacles.
• Observe a sufficient distance between float switch (4) and float switch locking device (3), for this could prevent the automatic switch-off causing the device to run dry.
• Make sure that the position of float switch (4) is adjusted in a way, that it does not lie flat on the ground. This could prevent the automatic switch-off causing the device to run dry.
• If required, lock the float switch (4) in the desired position by pushing the cable into the float switch locking device (3) at the side of the pump. (see fig. 9), when the float switch is at a certain water level, it will automatically start or shut off. (see fig. 9)

POSITIONING THE DEVICE
Please observe the following information regarding the device
set-up and before switching the device on:

• The float switch (4) must be able to move freely. The shaft into which the device is lowered must not restrict the mobility of the float switch (4) in any way.
• Do not leave the device running unattended.
• Make sure that the device is firmly placed on the ground or safely suspended.
• When using the device in bodies of water with natural, muddy ground, set the device up at a slightly elevation position, e.g. on bricks.
• Check whether the hose or pipe was attached properly.
• Make sure that the power cable (2) is not under tensile load and has enough clearance.
• Make sure that the mains connection corresponds to the specifications provided in the technical data.
• Check the mains socket for its proper condition and sufficient fusing.
• Make it impossible for moisture to reach mains plug or socket.

THERE IS A RISK OF ELECTRIC SHOCK!

Warning of electrical voltage

• Electric shock from damaged power supply cable.
• Make sure not to hold or suspend the device by the power supply cable under any circumstances.

Note
At the bottom of ponds and other waterbodies deposits may have accumulated over time. To prevent the device from being damaged, do not lower it all the way to the ground unless you are certain that the water is clean, in other words that the size of the dirt particles in the water does not exceed 5mm.

1. Fasten the supplied nylon cord to the transport handle (1) at the top of the device. (see fig. 10)
2. Lower the device into the water at a slight angle to allow any remaining air to escape. (see fig. 11)
3. If you want the device to be positioned on the ground, ensure that the latter is even.
4. Attach the nylon cord to an easily accessible position, so you can pull the device back out after pumping has been completed

OPERATION

Switching the device on

• Once you have completely installed the device as described in the Start-up chapter, you can switch it on

Warning of electrical voltage
Do not touch the mains plug with wet or damp hands.

• Plug the mains plug into a sufficiently fused mains socket.
• The device will be switched on when the float switch (4) is situated above the set or the maximum switch-on height. (see fig. 12 on position a)
• The device will be switched off as soon as the float switch  (4) reaches the set or the minimum switch-off height. (see fig. 12 on position b)

Once the device has been switched off, any water still remaining in the line can flow back through the device.

MANUAL OPERATION

• In manual operation it is possible to siphon off the media to a residual height of 5mm.
• Please note that for manual operation of the pumps the starting water level must amount to at least 60mm, but must not exceed the maximum of 250mm.

Warning of electrical voltage
Do not touch the mains plug with wet or damp hands.

Note
Running dry can cause damage to the device. Switch the device off before it can run dry.

• Hold onto the mains plug while pulling the power cable out of the mains socket.
• If necessary, pull the device out by means of the nylon cord.
• Lock the float switch (4) in the following position by manual operation: (see fig. 13)
  • With the float switch affixed in this position, the device is switched on permanently.
• Lower the device into the water at a slight angle to allow any remaining air to escape. Make sure that the position of the float switch (4) does not change.
• Plug the mains plug into a sufficiently fused mains socket.
  • The device switches on.
• Oversee the pumping process.
• When the de vice starts to suck in air, disconnect the power cable from the mains socket by holding onto the mains plug.

If the device switches off again after only a brief period of operation, the float switch might have come loose. Fix the float switch again as depicted.

Warning of electrical voltage
Do not touch the mains plug with wet or damp hands.

• Hold onto the mains plug while pulling the power cable out of the mains socket.
• If necessary, pull the device out by means of the nylon cord.
• Clean the device according to the Maintenance chapter.
• Store the device according to the Storage chapter.

ERRORS AND FAULTS

Warning of electrical voltage

• Do not touch the mains plug with wet or damp hands.

Warning of electrical voltage

• Tasks which require the housing to be opened must only be carried out by authorised specialist companies.
• Switch the device off.
• Hold onto the mains plug while pulling the power cable out of the mains socket.
  The device has been checked for proper functioning several times during production. If malfunctions occur nonetheless, check the device according to the following list.

The device does not start:

• Check the power connection.
• Check the power cable and mains plug for damages.
• Check the on-site fusing.
• Check whether the float switch is located above the automatic switch-on position.
• The device might have overheated and the thermal protection circuit is activated.
• If so, wait for approx. 10 minutes before restarting the device. If the device is not starting, have the electrics checked by a specialist company .
• The water temperature is above 35°C and the thermal protection circuit is activated.
• Check whether there are any foreign objects in the air intake ope-ning (5), the impeller, the reducer (7) and / or the hose or pipe. The device is running, but not pumping any water:
• Check the inside of the device for any remaining air. To do so, lower the device into the water at a slight angle and wait for the entire air to escape.
• Check whether the minimum water level has been reached, see technical data. In order to start pumping, the device requires a mini-mum water level.
• Check whether the hoses are blocked and whether the water contains any suspended matter with a particle size of more than 5 mm, which could clog up the device.
• Check whether the used hose diameter is too small.
• Check whether the hose line is kinked or blocked. Remove kinks and / or blockages.
• Check reducer (7) and / or elbow (8) or adaptor (9) for blockages.

The device is not switching off automatically:

• The float switch is hindered from lowering. Check whether the float switch can move freely. Remove any blockages or ensure sufficient freedom of movement for the float switch.

The device switches off after a brief runtime:

• Check whether the water temperature is too high. The device might have overheated due to a too high water temperature and the thermal protection circuit is activated.
• Check the power connection.
• Check the power cable and mains plug for damages.
• Check the on-site fusing.
• Check whether the hoses are blocked and whether the water contains any suspended matter with a particle size of more than 5 mm, which could clog up the device. The device might have over-heated due to the blockage and the thermal protection circuit is activated.

Insufficient or decreasing conveying capacity:

• Check whether the hoses are blocked and whether the water contains any suspended matter with a particle size of more than 5 mm, which could clog up the device.
• Check the hose diameter and the pump height. An excessive pump height paired with a small hose diameter can cause a reduction of the conveying capacity.
• Check whether the hose line is kinked or blocked. Remove kinks and / or blockages.

Notice

• Wait for at least 3 minutes after maintenance and repair work. Only then switch the device back on.
• Your device still does not operate correctly after these checks? Please contact the customer service. If necessary, bring the device to an authorized specialist electrical company for repair.

MAINTENANCE

• Activities required before starting maintenance

Warning of electrical voltage

• Do not touch the mains plug with wet or damp hands.
• Switch the device off.
• Hold onto the mains plug while pulling the power cable out of the mains socket.

Notes on maintenance
Inside the device, there are no parts that need to be maintained or lubricated by the user.

CLEANING

• * Clean the device with a soft, damp and lint-free cloth. Protect electrical components from moisture. Do not use any aggressive cleaning agents such as cleaning sprays, solvents, alcohol-based or abrasive cleaners to dampen the cloth.

• Rinse the reducer (7) as well as the other connections using clear water. (see fig. 14)
• Clean the bottom of the pump as well as the impeller by means of a jet of water.

WASTE

• This symbol on the product or in the instructions means that your electrical and electronic equipment must be disposed at the end of its useful life in a specialized container; Do not dispose it in the usual household waste container. In the EU there is special waste collection systems for subsequent recycling. For more information, contact with the local authority or the retailer from whom you purchased the product.
  • IMPORTED BY
  • www.edmproduct.com
  • ELEKTRO 3, S.COOP.C.L / F-43389675 MADE IN CHINA

WARRANTY

• The warranty period is 24 months from the date of purchase and covers all manufacturer’s failures regarding material and quality. This warranty applies only if the instructions for use have been followed, and it is voided if the device has been forced or used improperly, or if it has been repaired by an unauthorized person.

References

• Webarchitects Shared Hosting | Webarchitects Shared Hosting
• edmproduct.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>