EDM 30286 Magnifying Desk Lamp Instruction Manual
- June 14, 2024
- EDM
Table of Contents
EDM 30286 Magnifying Desk Lamp
INSTRUCTION MANUAL
Read this manual carefully before using the device and save it for future
reference. To reduce possible risk of fire, electric shock or personal injury,
keep in mind the following instructions:
GENERAL INFORMATION
- Before operating this appliance, read the following instructions. Keep the manual in a safe place so you can consult it at any time.
- After removing the packaging, check that the appliance is in good condition, and if you have any questions, do not turn it on.
- Contact your distributor or seller for the return of the appliance.
- This device is packed for protection against any damage or damage that may be caused by transportation.
- The packaging is made up of plastics and other materials that can be dangerous. Keep out of reach of children. These materials are recyclable and must be delivered in a unit of the appropriate recycling, respecting the environmental laws.
- This appliance has been designed for DOMESTIC USE only and must not be used with any other appliance, such as for example in a commercial, industrial or any other non-residential installation.
- Do not handle the appliance with wet hands and do not immerse it in water or any other liquid.
- Unplug the appliance from the mains before cleaning it.
- This device is not intended to be used by people (including children) with reduced physical capacities, sensory or mental, or lack of experience and knowledge, unless they have received instructions regarding use of the device or are accompanied by a responsible person.
- Keep the device out of the reach of children under 8 years.
- Children should be supervised during use, to make sure they do not play with the appliance.
- Do not continue using the appliance if you notice that it is not working properly. Turn it off immediately and look for the manufacturer or an authorized technical service so that a qualified technician can evaluate the damage and repair it if necessary.
- If the power cord is damaged, it must be replaced by the manufacturer or by a qualified technician to avoid the risk of electric shock.
- Turn off the appliance and disconnect the power cord from the power outlet before replacing any part or accessory, or before touching the moving parts of the device.
IMPORTANT SAFETY INSTRUCTIONS
- Connect the device only to an AC power source. The voltage indicated on the rating plate that is on the device, must match the voltage of the power supply.
- Always disconnect the appliance from the socket after use, to disassemble or clean it.
- Always mount and use the appliance on a stable and secure surface.
- Never place the appliance on or near heat sources, such as a gas / electric stove or inside a hot oven. Keep the power cord away from these sources of heat or sharp objects.
- Never handle the power cord with wet hands.
- The use of accessories or parts not recommended by the manufacturer may cause a fire, an electric shock or serious injuries.
- This device is manufactured to be used indoors. Never use it outdoors or in outside parts of the house.
ICONS
HOW TO USE
- Remove all packaging from the lamp.
- Attach the mount to the edge of any stable, horizontal surface.
- Insert the lower shaft of the arm into the hole in the bracket.
- Turn on the lamp by pressing the ON/OFF switch.
- Place the head of the lamp in the desired position.
CHANGING THE LED TUBE
- The lighting tube can be changed – the socket is G10Q – the reference is 31140.
- To change it, disconnect the lamp and remove the cap. Wait for the lamp to cool down before changing the tube.
- Rotate the head of the lamp, so that you can see the tube.
- Remove the clear tube protection cover and set it aside.
- Disconnect the 4-pin connector from the old tube from the socket and dispose of it safely.
- Fit the 4-pin connector of the new tube into the lamp holder. Press the new tube into the clips to ensure that the tube is firmly attached.
- Put the tube protection cover.
IMPORTANT FOR SAFE USE
- Only use indoors.
- Ambient temperature: -20°C / 40°C
- Humidity: <95%
- Never disassemble the lamp unless you are a qualified electrician.
- Unplug while making any repairs to the magnifying lamp.
- Never leave the lens alone in direct sunlight or where light may pass through it. Since it can cause a dangerous fire!
- If the external cable or cord of the appliance is damaged, it must be replaced exclusively by the manufacturer or its service agent or a qualified person, in order to avoid danger.
TECHNICAL SPECIFICATIONS
- 22W – G10Q
- 220/240V – 50Hz (AC)
- Lens diameter: Ø127mm
- Magnification power: 3 diopters.
- Movement first joint 120º turn of the head.
- Second joint movement 90º turn of the body.
- Third joint movement 90º turn of the body
WASTE
This symbol on the product or in the instructions means that your electrical
and electronic equipment must be disposed at the end of its useful life in a
specialized container; Do not dispose it in the usual household waste
container. In the EU there is special waste collection systems for subsequent
recycling. For more information, contact with the local authority or the
retailer from whom you purchased the product.
WARRANTY
EDM guarantees all its products and declines all responsibility for damages caused by improper installation / use of its articles.. This warranty applies only if the instructions for use have been followed, and it is voided if the device has been forced or used improperly, or if it has been repaired by an unauthorized person.
THE INVOICE IS THE PRODUCT WARRANTY THE MANUFACTURER DECLINES ALL RESPONSIBILITY DUE TO AN INCORRECT INSTALLATION OF THE APPLIANCE.
IMPORTED BY www.edmproduct.com
ELEKTRO3, S.COOP.C.L F-43389675 MADE IN CHINA
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>