ORTECH OD-SB4-100W LED Area Lights Instruction Manual

: June 17, 2024
: Ortech

Table of Contents

WARNING
CAUTION
INSTALLATION GUIDE
CUSTOMER SUPPORT
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

ORTECH OD-SB4-100W LED Area Lights

ORTECH OD-SB4-100W LED Area Lights

WARNING

WARNING — THE INSTALLATION MUST BE CARRIED OUT BY A QUALIFIED ELECTRICIAN.

LED Shoe Boxes are suitable for using in wet locations
Please keep the LED Shoe Boxes away from any corrosive substance, and please use dry or wet cloth when you clean it
LED Shoe Boxes can only be installed by a qualified electrician
Before installation or maintenance, please disconnect the power to prevent electric shock

Application Notice

Do not exceed using the standard working voltage: 100-347V AC, 50/60Hz
Be sure the power supply is turned off before installation
Switch off power of the mains supply or the connection lead respectively before doing any works
Please note waterproof, dustproof, electricity prevention and shockproof for the external power wires
Directly fix bolts on the installation stem through the hole on the mounting bracket
Be sure the connection between the wires is in good condition when installing the lamps, beware of leakage

CAUTION

PLEASE READ INSTRUCTION BEFORE COMMENCING INSTALLATION AND RETAIN FOR FUTURE REFERENCES.
Electrical products can cause death or injury, or damage to property.
If in any doubt about the installation or use of this product, consult a competent electrician.

INSTALLATION GUIDE

TYPE A (Slip-fitter)

Loosen the 4 screws on the lamp holder
Connect the wires correctly and put the wires into the lamp pole
Lock the screws well to fix the lamp on the lamp pole
Loosen the locking bolt with tools
Rotate the lamp and lock the screw after determining required angle
Locking bolt can be only compatible with a lamp pole that the outer diameter is ø60,
lamp adjustable angle is 0-90°

TYPE B part 1 (Square/Round pole mount with slip-fitter function)

Use tools to take screw apart and put installed iron bar away
Remove fixed screw
Open junction box, then pass the AC wire through it
Use tools to fix the lamp on square lamp pole
Connect the wires correctly
Make waterproof measures well
Close the junction box and finish installation

TYPE B part 2 (Square/Round pole mount with shipfitter function)

Remove the rubber mat when the lamp is installed on round lamp pole
Lamp adjustable angle is 0-30°

TYPE C (Square/Round pole mount)

For Type C Description 1~3, see Fig.1

Use tools to take screw apart and put installed iron bar away
Remove fixed screw
Open junction box, then pass the AC wire through it

For Type C Description 4~7, see Fig.2

Use tools to fix the lamp on square lamp pole
Connect the wires correctly
Make waterproof measures well
Close the junction box and finish installation

*For Type C Description , see Fig.3
* Remove the rubber mat when the lamp is installed on round lamp pole

TYPE D part 1 (Trunnion)

For Type D part 1 Description 1~2, see Fig.4

Mark the position of the fixing holes with flood light bracket
Drill the fixing holes

For Type D part 1 Description 3, see Fig.5

Input two expansion bolts

TYPE D part 2 (Trunnion)

Waterproof measures must be taken after connecting the wire correctly
Install the lamp well after putting the wires back into the trunking

Lamp adjustable angle is 0-90°
$TYPE D part 2 $Trunnion$$

TYPE E (Yoke)

**For Type E Description 1~2, see Fig.***

Mark the position of the fixing holes with flood light bracket
Drill the fixing holes

For Type E Description 3, see Fig.+

Input two expansion bolts

*For Type E Description 4~5 and , see Fig.,**

Waterproof measures must be taken after connecting the wire correctly
Install the lamp well after putting the wires back into the trunking

Lamp adjustable angle is 0-90°

TYPE F

For Type F Description 1~3, see Fig.9

Use a wrench to loosen the fixing screws on the bracket
Remove the bracket
Use a screwdriver to remove the bracket wiring cover screws

For Type F Description 4~5, see Fig.10

Fix the AC cable through the bracket to lock it on the lamp body
Fix the bracket on the pole after passing the AC wire through the bracket

For Type F Description 6~7, see Fig.11

Assembling the lamp body of the holder with the bracket, and lock the bracket fixing screws
Connect the wires according to the schematic diagram and also make waterproof treatment

For Type F Description 8, see Fig.12

Lock the bracket wiring cover plate to complete the installation

SB-PC SENSOR (Photocell)

Knock the sensing hole on the lamp with a hammer
Use a screwdriver to tighten the screw to fix the socket base and waterproof rubber ring on the lamp
Screw photocell (SB-PC SENSOR) into socket base as shown in the diagram on the left
$SB-PC SENSOR $Photocell$$