SUZOHAPP SH1950 19.5 Inch Video Topper Instruction Manual
- June 6, 2024
- SUZOHAPP
Table of Contents
SUZOHAPP SH1950 19.5 Inch Video Topper
Introduction
Congratulations with the purchase of your SuzoHapp Video Topper. Based on your configuration, the Video Topper is included with a LCD monitor or a light box. Further configurations specifies the colour of the bezel and whether a tower light is included or not. See ‘Chapter 3 – Model configurations’ for all available options. The chosen configuration may affect the available cables to connect into your installation.
Safety
UL, CE and FCC certified.
This monitor is only suitable for use in an interior environment where it’s
not sealed and not subject to dust, dirt, condensation (Pollution Degree 2)
(IP20).
It is not allowed to connect appliances to the monitor which does not comply
to SELV or Class II qualification.
Must be powered by LIMITED POWER SOURCE (LPS).
Unplug the monitor from the power outlet before cleaning. Do not use alcohol
(methyl, ethyl or isopropyl) or any strong dissolvent. Do not use thinner or
benzene, abrasive cleaners or compressed air. To clean the monitor, use a
cloth lightly damped with a mild detergent.
The slots located on the backside of the monitor case are for ventilation. Do
not block or insert anything inside the ventilation slots. It is important
that your monitor remains dry. Do not pour liquid into or onto the monitor. If
the monitor becomes wet do not attempt to repair it yourself. If the liquid
crystal materials leaks from the panel, it should be kept away from the eyes
or mouth. In case of contact with hands, legs or clothes, it must be washed
away thoroughly with soap.
Warning: This is a class A product. In a domestic environment this
product may cause radio interference in which case the user may be required to
take adequate measures.
Model configurations
| 103-02820132XX | Standard |
|---|---|
| 103 | Product group LCD toppers |
| XX | Model video topper |
| 03 | Topper without LCD ( light box ) |
| XX | Tower light |
x
72| Classic tower light chrome 2 lamp
73| Classic tower light chrome 3 lamp
82| Classic mini tower light chrome 2 lamp
83| Classic mini tower light chrome 3 lamp
X| Bezel| 0| Black bezel| x
X| RGB| 0| No RGB| ****
x
1| Surrounding RGB LEDs incl. controller
2| Vertical RGB LEDs incl. controller
3| Horizontal RGB LEDs incl. controller
4| Surrounding RGB LEDs only
5| Vertical RGB LEDs only
6| Horizontal RGB LEDs only
X| DVI or VGA loom| 1| VGA loom| ****
x
2| DVI loom
3| DVI – HDMI out loom
4| DVI – DisplayPort out loom
XXX| Standard/Custom| 2XX| Where 2 = USA market
XX = custom mounting and connection to cabinet type
| 2XX
Connections
The Video Topper is complete with several cables to connect into your
installation. The configuration of your Video Topper may affect the cables
used.
| | Pin Number|
---|---|---|---
Connector| Function| 1| 2| 3| 4| Type
J1| RGB LED
Strip
| +12Vdc| Green| Red| Blue| Molex Mini-Fit Jr. 39- 01-2041
Wire Color| Black| Green| Red| Blue
J2| TFT LCD| | | | | VGA / DVI / HDMI / DP
J3| Tower Light| +12Vdc| Middle Lamp| Bottom Lamp| Top Lamp| Molex 03-09-2040
Wire Color| Black| Red| Blue| Yellow
J4| Power in| | | | | DC Plug Contra 2,35mm
J5| Ground wire| | | | | Ring terminal (3mm / M3)
Video
When an LCD monitor is included in your Video Topper, connect it with the
video signal cable (VGA, DVI, HDMI or DisplayPort). HDMI or DisplayPort is
converted to DVI inside the Video Topper.
RGB LED strip
If you have chosen to supply your own RGB LED controller, connect the LED
strip using a receptacle which fits the Molex 39-01-2041 Mini-Fit Jr plug.
Tower Light
When a Tower Light is mounted on your Video Topper, connect it using a
receptacle which fits the Molex 03-09-2040 plug.
Power
To power the monitor and / or RGB LED controller, connect 12Vdc using a power
supply with a 2.5mm power plug. Recommended power supply: 150-0072.
Grounding
Use the ground ring to ground the Video Topper. Depending on your
configuration; the LCD monitor, Video PCB, RGB LED controller and Tower Light
are grounded.
RGB LED Operation
Based on your configuration, the Video Topper comes with or without an RGB LED
controller.
Video Topper with controller
Your Video Topper is included with an RGB LED controller and comes with a
matching RF remote controller. The remote controller allows you to turn the
light strip on or off and adjust the lightning. Several options are available,
such as jumping or fading colours as well as showing a static colour. The
intensity of the lightning and the speed of rotating colours can be changed
using the intensity and speed buttons.
Video Topper without controller
You have chosen to supply your own RGB LED controller. Connect your controller
to the installed LED strip using a receptacle which fits the Molex 39-01-2041
Mini-Fit Jr plug. See the corresponding manual of your controller for
instructions of use.
Monitor specifications
Panel
| Manufacturer | Part No. |
|---|---|
| LG | LM195WD2-SLA1 |
Absolute Maximum Ratings
| Item | Unit | Min | Typical | Max | Remarks |
|---|---|---|---|---|---|
| Operating Temperature | °c | 0 | – | 50 | |
| Storage Temperature | °c | -20 | – | 60 | |
| Operation Humidity | % | 10 | – | 90 | |
| Storage Humidity | % | 10 | – | 90 |
Input characteristics
Description| Signal| Unit| Min| Typical| Max|
Remarks
---|---|---|---|---|---|---
| Input| VDC| 11.4| 12| 12,6|
Consumption| A| | 1,9| |
RGB Input
| Analog RGB| VPP| 0| 0.7| –|
Sync| VDC| 0| 5| 5.5|
H Frequency| KHz| 48| 60| 76|
V Frequency| Hz| 48| 60| 76|
DVI-D Input
| DATA/CLK| VPP| 450| 500| 900|
Display Characteristics
| Item | Unit | Specifications |
|---|---|---|
| Screen Diagonal | [inch] | 19.5 |
| Active Area | [mm] | 433.92(H) x 236.34(V) |
| Pixels | 1600×900 | |
| RoHS Compliance | RoHS Compliance |
Optical Characteristics
| Item | Unit | Conditions | Min. | Typ. | Max |
|---|---|---|---|---|---|
| White Luminance | [cd/m2] | Center point | 200 | 250 | – |
| Contrast Ratio | 700 | 1000 | – | ||
| Response Time | [msec] | Gray to Gray | – | 14 | 25 |
Viewing Angle
| [degree] [degree]| Horizontal (Right) CR = 10 (Left)| 170| 178| –
[degree] [degree]| Vertical (Upper) CR = 10 (Lower)| 170| 178| –
Signal Input (Analog RGB, TMDS(DVI))
| Item | Description | Resolution |
|---|
Resolutions
| XGA| 1024×768
720P (HD)| 1280×720
WXGA| 1366×768
HD+| 1600×900
FHD| 1080P
Monitor Operation
-
Color LED: This LED shows the state of the controller.
- Green is the “normal state”.
- Red is the “Off mode”. (Can’t find Sync. signals)
- Amber is the “DPMS mode” (Display Power Management Signaling).
-
PC Settings: The PC needs to be set to an appropriate graphics mode that has the same resolution as the LCD panel to have clear screen image. The vertical refresh rate should be set to one of
56~75Hz, non-interlaced signal. -
LCD display System Settings: The OSD (On Screen Display) provides certain functions to have clear image and others. This board supports 5 buttons OSD operation as a standard. The control functions defined on OSD operation are as below.
-
PC Graphics Output: Signal quality is very important. If there is noise or instability in the PC graphics output, it may result in visible noise on the display. Refer to the graphic modes table in specification section for supported modes. Non-interlaced & interlaced video input is acceptable.
-
VGA or DVI-D cable: See ‘Chapter 4 – Connection’.
-
Power supply: See ‘Chapter 4 – Connection’.
-
Power on: Switch on the monitor by using the on/off switch on the OSD control buttons.
-
PC Setting: The controller has been designed to take a very wide range of input signals. However, to optimize the PC’s graphic performance, we recommend choosing 60Hz vertical refresh rate. This will not cause screen flicker.
The chosen OSD settings will be stored in memory. The OSD menu can be cleared from the screen by moving the selection bar to the EXIT MENU icon pressing the SEL button. The OSD menu will automatically be cleared from the screen after a few second of non-use.
OSD Menu
OSD GUI Control Table
| MAIN | SUB MENU | CONTROL |
|---|
Picture
| Brightness| 50(0~100)|
Contrast| 50(0~100)|
Sharpness| 2( 0 ~ 4)|
Color
| Color Status Management| User(User, Warm, Normal, Cool)|
Red| 50(0~100)| ****
PC ONLY
Green| 50(0~100)
Blue| 50(0~100)
Auto Color| To Start
Screen
| Auto Configure| To Start|
H Position| 50(0~100)| ****
PC ONLY
V Position| 50(0~100)
Clock| 50(0~100)
Phase| 30(0~100)
OSD
| Language| English(English, Deutsch, Francais, Italiano,
Espanol, Korean)
|
H Position| 50(0~100)|
V Position| 50(0~100)|
Transparency| 33 (0~100)|
OSD Time| 10(3~30)|
SETUP
| Source| RGB, DVI, AUTO|
Factory reset| To Start|
Aspect| Off(On/Off)|
Mounting instructions
The Video Topper can be mounted with standard or custom mounting feet at the
bottom. The feet includes two M6 mounting bolts, with a space of 90mm or 125mm
between the bolts. Changing between these two dimensions requires re-assembly
of the feet (four M4 screws at the bottom).
Standard mounting feet.
Custom Mounting Features
Mounting feet and connections available for the following cabinet types;
- Everi Player Classic (103-0282013206)
- Konami Concerto (103-0282013207)
- IGT Crystal Dual (103-0282013209)
- IGT S3000 (103-0282013212)
Dimensions
Accessories and replacement parts
Recommended Multi-Media player Suzohapp 95-0794-00. Input Micro-SD and USB (memory devices not included). Output HDMI (cable not included). Power supply included. Recommended HDMI splitters; Tripp-Lite B118-004-HDR Quest Technology HDI-4214
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>