FIRSTECH FTI-STK1 Vehicle Coverage Instruction Manual

FIRSTECH FTI-STK1 Vehicle Coverage

FTI-STK1: Vehicle Coverage and Preparation Notes

Make| Model| Year| Install| CAN| IMMO| BCM| Clutch| I/O Changes
---|---|---|---|---|---|---|---|---
DL-SUB9| | | | | Type| | | Green White/Blue
Subaru| Ascent STD KEY AT| 2019-22| Type 2| 40-Pin| B| DSD| N/A| N/A
| (Canada)| | | | | | |

Covered vehicle use BLADE-AL-SUB9 firmware and the following required accessories, Weblink Hub & ACC RFID1. Flash module, and update the controller firmware. Please follow the directions for RFID programming before attempting to program the BLADE module to the vehicle.

CAN: Type 2 CAN connections are made using the 40-Pin BCM connector and require connecting the white 2-pin female connector to the black male 2-pin connector at marker [D] of the illustration.

Immobilizer: Type B IMMO requires connecting the black and white 2-pin connectors at marker [C] of the illustration.

Lights: Parking lights are pre-wired in the FTI-STK1 harness. Replace the green/white wire of the CM I/O connector with the pre-terminated green/white wire of the harness.

ACC-RFID1 (REQUIRED): SUB9 firmware does not provide immobilizer data, an ACC-RFID1 is therefore required for remote start.

2nd START: The FTI-STK1 harness is pre-wired with a red/white 2nd START output (not required in TYPE 2), cut and insulate the provided wire to prevent short circuits when not used.

I/O Changes: None required

Advisory 1 : Program ACC-RFID1 before attempting to program the BLADE module to the vehicle.
Advisory 2: Secure all 2-pin connections, both used and unused, to the main harness body.

FTI-STK1: Installation and Configuration Notes

A. REQUIRED ACCESSORY
B. ADAPTER NOT REQUIRED
C. REQUIRED CONFIGURATION (TYPE B IMMO)
D. REQUIRED CONNECTION
E. NO CONNECTION

FEATURE COVERAGE

IMMOBILIZER DATA|
---|---
ARM OEM ALARM|
DISARM OEM ALARM|
DOOR LOCK|
DOOR UNLOCK|
PRIORITY UNLOCK|
TRUNK/HATCH RELEASE|
TACH OUTPUT|
DOOR STATUS|
TRUNK STATUS|
BRAKE STATUS|
E-BRAKE STATUS|
A/M ALRM CONTROL FROM OEM REMOTE|
A/M RS CONTROL FROM OEM REMOTE|
A/M RS CONTROL FROM OEM REMOTE|

FTI-STK1 – AL-SUB9 – Type 2 2019-22 Subaru Ascent STD KEY AT (CA)

Notice:

LED Programming Error Codes

Module LED flashing RED during programming
1x RED = Unable to communicate with RFID or immobilizer data.
2x RED = No CAN activity. Check the CAN wire connections.
3x RED = No ignition detected. Check the ignition wire connection and CAN.
4x RED = Required ignition output diode not detected.

INSTALL GUIDE

CATRIDGE INSTALLATION

1. Slide cartridge into unit. Notice button under LED.

2. Ready for Module Programming Procedure.

MODULE PAROGRAMING PROCEDURE

1. For this installation, the Weblink HUB is required.

2. Remove OEM key 1 from keychain.
   Place all other key fobs at least 1 foot away from the Weblink HUB. Failure to comply may result in damage to other key fobs or interfere with the key fob reading process.
   

3. Flash the module using the Weblink HUB. Follow the on screen instructions to complete the key fob reading process.

4. WARNING: Do not press the module programming button. Connect power first. Connect module to vehicle.
   

5. Using OEM key 1, turn key to ON position.
   

6. Wait, LED will turn solid BLUE for 2 seconds.

7. Turn key to OFF position.

8. Module Programming Procedure completed.

WWW.IDATALINK.COM Automotive Data Solutions Inc. © 2020

References

• iDatalink - Home

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>