BUSHWACKER 70911-02 Nissan Frontier Pocket Style Flares Installation Guide
- June 13, 2024
- BUSHWACKER
Table of Contents
Nissan Frontier
Pocket Style® Flares
Rear Pair Only
Set Part #70911-02
PRIOR TO INSTALLATION
A) Bushwacker® only approves installing the flares according to these written
instructions with the hardware provided. WARNING: Failure to install
according to these instructions will invalidate the warranty. This includes,
but is not limited to using alternative installation methods, hardware, or
materials. DO NOT USE: Loctite, SuperGlue, or similar products on the hardware
or the flares.
B) Fit: Verify the fit of the flares to vehicle. (Some filing, sanding, or
cutting may be necessary to ensure proper fit).
C) Painting: (Optional) if paint is desired it must be done prior to
installing flares on vehicle. Clean outer surface with a good grade degreaser.
DO NOT USE LACQUER THINNER OR ENAMEL REDUCER AS A DEGREASER. Wipe outer
surface thoroughly with a tack rag prior to paint. Application of plastic
adhesion promoter for ABS plastic as per your paint system manufacturer’s
recommendations is required. Paint flares using a high quality enamel, or
polyurethane automotive paint. If painting edge trim (not recommended), use a
flex additive.
D) Performance: Using larger Tires may increase the area required to turn the
vehicle. Some Tire/Rim combinations may require lowering bump stops and or
installing steering stops to prevent tire from contacting flare.
E) Exhaust System: Modifications may be necessary to maintain a minimum 4”
clearance between flares and exhaust pipes. (Exhaust gases should not vent
directly onto flares)
F) Metal Protection: All exposed fasteners and bare metal should be treated
with rust resistant paint BEFORE installing flares. Spray inner fender wells
with undercoating AFTER flare attachments have been completed.
G) Decals: Flares may interfere with existing decals on vehicle. If you wish,
remove decals prior to installation of flares.
H) Care & Cleaning: Bushwacker fender flares are built to last; any detergent
you use to wash your vehicle is sufficient to clean the flare. Do not use any
harsh abrasive detergents.
Included in Hardware Kit:
If your flares already have the edge trim installed, skip to Front Flare Installation Step 1.
EDGE TRIM INSTALLATION
A. Peel two to three inches of red vinyl backing away from Edge Trim
(GP1-0025) tape. Applying the adhesive side of the edge trim to the inner side
of the flare, affix the edge trim to the top edge of the flare (the portion
that comes in contact with the vehicle).
B. Press edge trim into place along the top edge of the flare in one-foot
increments, pulling red vinyl backing free as you continue to work your way
around the top edge of the flare.
Pocket Hardware Installation Procedures:
Put a Washer (WA1-0012) on each Bolt (SW1-0067).
Put each Bolt/Washer combination through a pocket hole in the flare, Bolt head and Washer on the outside.
Place a Nut (NU1-0019) over the end of each Bolt and tighten, using a 1/2” wrench for the Nut and the supplied Torx Bit (SW1-0052) for the Bolt. Repeat for remaining pockets.
Rear Flare Installation Procedures (Passenger’s Side):
NOTE: For short bed installation only: Inspect rear wheel well and note that there are (3) square holes at the top. On Pro4X models there will be (3) screws in this location that need to be removed. Proceed to Step 6.
Remove (7) factory installed Phillips screws. Retain screws as these will be reused to install the new flare. Remove and discard mudflaps. NOTE: for short bed installation proceed to Step 8.
Place fender flare on vehicle and align with holes. For short bed installation: Install (3) RV1-P006 retainers in the locations shown. (Pro4X will reuse (3) factory screws.) For long bed installation install (3) SW1-0050 Truss Screws.
NOTE: For long bed installation only: Hold flare in position and mark (3) locations where holes in flare align with truck fenderwell. Mark these locations with a grease pencil. Proceed to Step 6.
NOTE: for long bed installation only: Install (3) MT1-0014 Black Mylar Tabs and (3) CL1-0005 “S” Spring Clips at locations marked in Step 5.
Reinstall (6) factory screws. Rear flare installation complete. Repeat for
opposite side.
Edge Trim Tool Procedures:
Using supplied Edge Trim Tool (ET1-0002), seat edge trim against vehicle by hooking curved end under edge trim at one end of flare. Next, slide around outer edge of flare to the other end.
Using flat end of supplied Edge Trim Tool (ET1-0002), seat edge trim against flare by inserting straight end between edge trim and flare at one end. Next, slide around entire edge to the other end.
Rev-0 11/11/2021
For complete fitment info visit :
www.bushwacker.com
TOOLS FOR EASY INSTALLATION:
- Utility Knife
- #2 Phillips Driver
- Awl or Similar Pointed Tool
- Grease Pencil
PLEASE READ: Dirt and debris can become lodged between the fender flares and the vehicle’s fenders, causing scratching and paint wear from vibration. Lund International is not responsible for any damage, and the installation of our fender flares is done with the buyer’s understanding that this scratching and paint wear may occur.
LIMITED LIFETIME WARRANTY AGAINST
ANY MANUFACTURING DEFECTS
• To claim a warranty, you must provide Proof of Purchase.
The material that your product is made from can be recycled. Please also
consider recycling the packaging that your product came in.
4325 HAMILTON MILL RD. • BUFORD, GA 30518 • 1-800-234-8920 (USA AND CANADA) • FAX 800-438-3788
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>