FIRSTECH REN500-1WFX Keyless Entry System User Guide
- June 1, 2024
- FIRSTECH
Table of Contents
FIRSTECH REN500-1WFX Keyless Entry System
1 WAY 3 BUTTON REMOTES
| Tap the Lock Button to lock your doors and/or arm your vehicle. Hold this
button for 3.5 seconds to activate panic/vehicle locater
---|---
| Tap the Unlock Button to unlock your doors and/or disarm your vehicle.
| Hold this button for 2.5 seconds to pop your trunk. If not equipped, ask
your Authorized Dealer for details on how to get it.
| Hold this button for 2.5 seconds to start your vehicle. Your vehicle’s
parking lights will flash once and/or siren will chirp once for confirmation.
Repeat and your vehicle will shut off.
| Auxiliary 1: Tap Start Button and then tap the Lock button twice.
| Auxiliary 2: Tap Start Button and then tap the Unlock button twice.
| Tap these two buttons at the same time to turn the horn or siren chirps on
or off. Hold them for 2.5 seconds to turn your FT-DAS or Shock Sensor on or
off.
| Tap these two buttons at the same time to turn the drive lock on or off
(also known as ignition controlled door locks). Hold them for 2.5 seconds to
Valet Mode off. Turn Ignition On and hold these two buttons to turn on.
| Tap these two buttons at the same time to turn Activates the built in Turbo
Timer function. Hold them for 2.5 seconds to activate Passive locking/arming.
Your system will lock/arm after 30 seconds if enabled.
Patent: https://firstechllc.com/patents/
ALARM LED CODES
If you have an alarm and optional LED(s) installed, it will flash once a second if armed. If your alarm is triggered then the LED(s) will flash more than once until it is disarmed. See the table below for what each LED code represents.
| ALARM TRIGGER EVENT | LED FLASHES |
|---|---|
| Door, Hood, Trunk, or Ignition On triggered | 2, Pause, Then Repeat |
| Full triggered shock sensor | 3, Pause, Then Repeat |
| Optional sensor triggered | 4, Pause, Then Repeat |
| Panic Mode | 5, Pause, Then Repeat |
Valet Mode: If your remote start is not working, you may be in Valet
Mode. Your parking lights will also not flash. Your doors will still lock and
unlock. To exit Valet Mode, tap the Lock and Trunk buttons or turn the
Ignition On and then tap the foot brake 10 times or reprogram your remote(s).
To reprogram your remote first cycle the key in the ignition 5 times within 7
seconds. Parking lights will flash. After that tap the Lock button on your
remote. Repeat for any additional remotes. If you receive two parking light
flashes, your system has exited remote programming mode and you must retry.
START ERROR CODES
| PARKING LIGHT FLASHES | REMOTE START ERROR |
|---|---|
| 3 then 1 | Motor running |
| 3 then 2 | Key in ignition on position |
| 3 then 3 | Door open (manual transmission only) |
| 3 then 4 | Trunk open |
| 3 then 5 | Foot brake on |
| 3 then 6 | Hood open |
| 3 then 7 | Reservation off (manual transmission only) |
| 3 then 8 | Tach or voltage sensing failure |
| 3 then 9 | FT-DAS sensor shutdown |
| 3 then 10 | System is in Valet Mode |
Register online at www.compustar.com within 10 days of purchase to activate your new remote’s warranty.
CUSTOMER SUPPORT
Questions/comments?
Contact us at 888-820- 3690 from 8 AM to 5 PM PST.
Also please visit www.compustar.com for a complete
user’s manual.
References
- Compustar | Remote Starters | Security Systems | Car Alarms
- Compustar | Remote Starters | Security Systems | Car Alarms
- Patents | firstechllc.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>