FEIT Electric LEDR6XLV_6WYCA Connect LED Canless Recessed Downlight Installation Guide

FEIT Electric LEDR6XLV_6WYCA Connect LED Canless Recessed Downlight

Specifications

• Brand: FEIT ELECTRIC
• Location: PICO RIVERA, CA
• Website: www.feit.com

Product Information
The FEIT ELECTRIC product is designed to provide efficient lighting solutions for various applications. With a focus on quality and innovation, this product aims to enhance the lighting experience for users. Product Usage Instructions

1. Installation: Follow the provided installation guide to securely set up the product in the desired location.
2. Power On/Off: Use the designated power switch or remote control to turn the product on and off.
3. Adjust Settings: Customize the lighting settings according to your preferences using the available controls.
4. Maintenance: Regularly clean the product and ensure proper functioning for longevity.

READ BEFORE INSTALLATION SAVE THESE INSTRUCTIONS
Please read and understand this entire manual before attempting to assemble, operate or install this product. This product must be installed in accordance with any applicable installation code(s) by a qualified electrician or person familiar with the construction and operation of the product and the hazards involved.

1. WARNING: RISK OF SHOCK. House electric current can cause painful shock or serious injury unless handled properly. For your safety, always remember to:
   •  Ground the fixture to avoid potential electric shocks and to ensure reliable starting.
   • Double-check all connections to be sure they are tight and correct.
   • Wear rubber-soled shoes and work on a sturdy ladder.
2. Tllis fixture is designed for use in a circuit protected by a fuse or circuit breaker. It is also designed to be installed in accordance with local electrical codes. If you are unsure about your wiring, consult a qualified electrician or a local electrical inspector and check your local electrical code.
3. WARNING: RISK OF CUTS. Some metal parts in the fixture may have sharp edges. To prevent cuts and scrapes, wear gloves when handling the parts.
4. Account for small parts and destroy packing material, as these may be hazardous to children.
5.  Risk of Fire – MINIMUM 90°C SUPPLY CONDUCTORS. If uncertain, consult an electrician.
6.  Tllis device is not intended for use with emergency exits.
7.  Risk of pinching – Do not place hands under springs during removal of the downlight.

VAPOR BARRIER MUST BE SUITABLE FOR 90 °C.
FOR USE IN NON-FIRE-RATED INSTALLATIONS ONLY.

Product Specifications

• 120VAC, 60Hz, 12 Watts
• Dimmable
• Suitable for Wet Locations

NOTICE:
All electrical connections must be in accordance with local and National Electrical Code (N.E.C) standards. If you are unfamiliar with proper electrical wiring connections, obtain the services of a qualified electrician.
Remove the fixture and the mounting package from the box to make sure that no parts are missing by referencing the illustrations on the installation instructions.
CAUTION: Tum off the main power at the circuit breaker before ~ installing the fixture in order to prevent possible shock.

• Supplier’s Declaration of Conformity:
• 47 CFR § 2.1077 Compliance Information
• Responsible Party:
• Feit Electric Company
• 4901 Gregg Road,
• Pico Rivera, CA 90660, USA
• Unique Identifier:
• FEIT ITEM# LEDR6XLV/6WYCA

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
• Any changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.

WARRANTY

This product is warrantied to be free from defects in workmanship and materials for up to five years from date of purchase. If the product fails within the warranty period, please contact Feit Electric at info@feit.com visit feit.com/contact- us for instructions on replacement or refund. REPLACEMENT OR REFUND IS YOUR SOLE REMEDY. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTIES ARE LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY. LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES IS HEREBY EXPRESSLY EXCLUDED. Some states and
provinces do not allow the exclusion of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state or province to province.

PACKAGE CONTENTS

Before beginning installation of this product, make sure all parts are present. Compare parts with package contents list and diagram. If any part is missing or damaged, do not attempt to assemble, install or operate this product.

Tools Required (Not Included)

• Screw driver
• Recessed lighting hole saw (recommended)
• Scissors
• Pencil

| COMPONENTS INCLUDED
---|---
A| (1) LED RECESSED DOWNLIGHT
B| (1) T-CONNECTORS
C| (1) 6FT LOW VOLTAGE CABLE
D| (1) CUT OUT TEMPLATE
E| (1) INSTRUCTION MANUAL

Package Components

PRODUCT ELECTRICAL RATINGS

The foam insert between the trim and ceiling of this panel will create an air tight seal and is required for the ASTM Air Tight Certification. Suitable for Type IC.

CHOOSE A WHITE COLOR SETTING

NOTICE: The toggle switch is located on the power supply box

PICK YOUR FAVORITE LIGHT COLOR

BEFORE INSTALLING

• You can lock in one white color temperature or change among multiple white color temperatures. The unit will memorize the last white color temperature and default to it automatically.
• When the slide switch is set to SW (Soft White), the white color temperature is set at 2700K.
• When the slide switch is set to BW (Bright White), the white color temperature is set at 3000K.
• When the slide switch is set to NW (Neutral White), the white color temperature is set at 3500K.
• When the slide switch is set to CW (Cool White), the white color temperature is set at 4000K.
• When the slide switch is set to DL (Daylight), the white color temperature is set at 5000K.

YOUR LIGHT COLOR ANYTIME WITH A REGULAR WALL LIGHT SWITCH

• Set the slide switch on the power supply box to SWITCH.
• Toggle your light switch ON and OFF within 0.5-2 seconds to cycle through the five different white color temperatures.
• If the fixture is left OFF for over 10 seconds then turned ON, the fixture remembers the last white color temperature selected and displays that color when turned on again.
• The reset function is used when using multiple color selectable lighting products operating from the same light switch. In the event that multiple fixtures are not displaying the same color at the same time, the fixtures must be RESET using your existing light switch. Simply toggle the wall switch ON and OFF 7 times, leaving
• it in the ON position for 1 second intervals (e.g., with the fixture in the ON position, toggle the wall switch
• OFF then ON, leaving it ON for 1 second, then OFF then ON, leaving it ON for 1 second (repeat 7 times).

PRE-INSTALLATION REVIEW

• Turn the power OFF from the breaker panel before starting installation.
• Locate a suitable location for the fixture and cut the correctly sized hole in the drywall or ceiling tile (for a suspended
• T-Bar type ceiling)- refer to Hole Cut Out Template for appropriate size.
• Know the location of your joist before making any cuts.
• Use the slide switch to choose a preferred color temperature before installing (2700K, 3000K, 3500K, 4000K, 5000K)

INSTALLATION INSTRUCTIONS FOR RECESSED HOUSING

1. Determine how many downlights will be installed with the Power Supply (max. 145W). Carefully measure where each fixture will be installed.

2. Use the provided cutout template to mark your hole location. Cut a 6 3/8 in. hole in the ceiling as round as possible using a recessed= lighting hole saw (and the provided cutout template). Make sure the opening is not larger than the outer trim of light.
   

3. Gently extract the knockout from the Power Supply Box (A) using a screwdriver or punch driver.
   

4. Open the cover of the Power Supply Box (A). Feed the supply wire into the knockout hole using a 3/8 in. clamp connector (not included). Using Quick Connectors (G), connect the 120V line (black) wire to the black wire, connect the neutral (white) wire to the white wire, and connect the ground (green) wire to the green wire. This power supply box needs to be grounded. Wires inserted into the quick connectors must meet the “Wire Guage and Strip Length Requirements.

5. After inserting the supply wire into the quick connectors, verify the connection by following these simple tests: Hold the quick connector with one hand and with the other hand pull at the connected wires to ensure proper wire connection.
   Ensure a sufficient amount of wire is visible through the clear shell for visual verification.

6. Insert the Power Supply Box (A) into the ceiling opening and secure it with the latch. Mount to structure using the provided screws (E).

7. Connect the T-Connector (C) to the low voltage cable originating from the Power Supply Box (A). Then attached the LED Downlight (B) to the T-Connector (C). If adding more downlights, attach a Low Voltage Cable (D) to the end of the T-connector. NOTE: The last connected down light will use the Single Connector. T-Connector must not be the last connector.

8. Direct the Low Voltage Cable (D) towards other downlight spots and ensure to leave enough slack through each opening for ease of fixture connection, approximately 6 feet apart. Place the excess cable in the ceiling securely.
   contact with insulation as they are specifically rated for this kind of contact. DO NOT CUT THE LOW VOLTAGE CABLE.

9. Repeat steps 7 and 8 for any additional downlights linked to the system.

10. Before restoring power at the breaker, make sure all LED downlights= are connected. Hold the spring clips against the fixture and gently guide into the ceiling until the clips snap into place. The fixture should be flush with the ceiling.
    NOTE: Ceiling thickness must be 1/2″ to 3/4″.

11. Restore the power at the breaker panel.

WIRE GUAGE AND STRIP LENGTH REQUIREMENTS

NOTE:  the jacket of the cable is not in the U quick connector ensure the strip length is correct and/or verify the wire is fully inserted.

CUTOUT TEMPLATE – For a 6 3/8 in. hole.

FEIT ELECTRIC COMPANY | PICO RIVERA, CA | www.feit.com

References

• Energy Saving Light Bulbs, Light Fixtures | CFL, LED & More

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>