PARTS IP12 Omron 18 Ingressi 12 Uscite Controller User Manual

: June 17, 2024
: PARTS

Table of Contents

PARTS IP12 Omron 18 Ingressi 12 Uscite Controller
Product Information
Product Usage Instructions
Front panel description
Parameters
Connection and connectors description
**Jumper settings
Remote Control
QUICK setup
**Product details
European Union Declaration of Conformity
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

PARTS IP12 Omron 18 Ingressi 12 Uscite Controller

Product Information

Specifications

Universal 12 outputs with + voltage outputs
Output current: max. 500mA per output, 500 mA total
Output voltage from controller max. 16 V DC
Controller supply voltage 10 ~ 16 V DC, max. 0.7 A
LED indication: DIR, BPF, PREAMP
LAN 10/100 MBit with filter and protection
ONLY DHCP IP address – not static

Front Panel Description
LED – Status LED

ANT – antenna/direction is selected
PRE – PREAMP is ON
BPF – BPF is selected, OFF = ByPass
ON – control is ON

Rear Panel Description

LAN – 10/100 Mbit LAN with DHCP
USB – USB port for FW upload
DB15 male – to controller

Connection and Connectors Description
D-SUB 15 PINOUT

Jumper Settings
When using OLI IP 12 with a 7ANT controller or any other hardware and you need to use the DIR 6 pin, you have to short the internal jumper.
Open enclosure and short JP1.

Remote Control
OLI IP 12 could be controlled in three basic ways:

CLASSIC User Interface (UI) – a similar look to HW controllers
BEAM MAP UI – automatically generated beam map from your location
OTHER – use your code, NodeRed, Stream Deck, etc.

Product Usage Instructions

Front Panel Usage
To check the status of the controller:

If the ANT LED is on, the antenna/direction is selected.
If the PRE LED is on, the PREAMP is ON.
If the BPF LED is on, the BPF is selected; if it’s off, it’s in Bypass mode.
If the ON LED is on, the control is ON.

Frequently Asked Questions (FAQ)

Q: Can I use the OLI IP 12 with other antenna systems?
A: Yes, you can use the OLI IP 12 with other antenna systems by following the appropriate connection and setup procedures.

NEW ITEMS RX PARTS TX PARTS CONTROLLERS VHF/UHF/LORA PARTS & ACCESSORIES KITS CUSTOM
This is a manual page for the OLI IP 12 controller. This box is directly designed for our K9AY++/4-WAY beverage system and also the 7ANT switch controller.

Jump to

Front panel description
Rear panel description
Parameters
Connection and connectors description Jumper settings
Remote control
- UI examples
- QUICK setup
Product details

Front panel description

LED – Status LED

ANT – antenna/direction is selected
PRE – PREAMP is ON
BPF – BPF is selected, OFF = ByPass
ON – control is ON

Rear panel description

LAN
- 10/100 Mbit LAN with DHCP
USB
- USB port for FW upload
DB15 male
- to controller

Parameters

Universal 12 outputs with + voltage outputs
Output current: max. 500mA per output, 500 mA total
Output voltage from controller max. 16 V DC
Controller supply voltage 10 ~ 16 V DC, max. 0.7 A
LED indication: DIR, BPF, PREAMP
LAN 10/100 MBit with ﬁlter and protection
ONLY DHCP IP address – not static.

Connection and connectors description

There is a DB15 male connector with a power supply and output pins. This controller has got positive output driver. It means – when the PIN is switched remotely ON, the supply voltage is switched to this output PIN. There is also an internal electronic fuse (short protection).
You can directly connect the K9AY++/4-WAY or 7ANT remote controller to this connector by 1:1 wire connection. You can also connect any of your devices which is controlled by positive voltage (12 to 16 V) and max. 0.5 A total. OLI IP 12 works as a remotely controlled group of switches:

D-SUB 15 PINOUT

**Jumper settings

**

When you use OLI IP 12 with 7ANT controller – or with any your HW – and you need to you DIR 6 pin, you have to short internal jumper. Open enclosure and short JP1

Remote Control

OLI IP 12 could be controlled by three basic ways. If you want to know more about REMOTE SYSTEM, please read our technical articles.

CLASSIC User Interface (UI)
- There are UI with a similar look as the HW controllers. You can use this web page UI to control outputs by clicking on buttons, you can change labels, color, font size, etc.
BEAM MAP UI
- This is UI with an automatically generated beam map from your location. There are preconﬁgured templates for different HW (K9AY, 7ANT, 4SQ, 8 Circle etc.). You can change the antenna (port) direction, antenna beam width, colors etc.
OTHER
- You can use your code, NodeRed, Stream Deck, etc. Please, contact us for API details.

UI examples

QUICK setup

Mike DM5XX has prepared the Entry Point and Easy Assistant pages. This is the best way to go, see all possibilities of our UIs. Please, start with the ENTRY POINT manual page
QUICK UI setup link is there: EASY ASSIST
Please, follow our YouTube channel

IMPORTANT NOTE: We recommend a VPN while using remote access from outside your network in general.

**Product details

**

Included in package

The controller was assembled and tested
DB15 female connector with cover

Manufacturer:
Ing. Jan Šustr
ID 05476356, VAT CZ8407024780
Palachova 1777/7, 591 01 Žďár nad Sázavou, Czech republic, Europe

General instructions:
Please also read the general instructions before handling the product.

European Union Declaration of Conformity

Manufacturer Ing. Jan Šustr (QRO.cz):
ID 05476356, VAT CZ8407024780
Palachova 1777/7, 591 01 Žďár nad Sázavou, Czech republic, Europe

declares that the assembled product: OLI IP 12
is compatible with the relevant Union harmonization legislation directives: EMC Directive 2014/30/EU
ČSN EN 61000-6-3 ed. 2
ČSN EN 61000-6-1 ed. 2 (333432)
On behalf of Ing. Jan Šustr (QRO.cz) Ing. Jan Šustr, CEO
11th June 2023

OLI IP 12

ABOUT CONTACT ALL YOU NEED TO KNOW FAQ TRACK & TRACE ACCOUNT BLOG
2021 – 2023 © hamparts. shop. All Rights Reserved. Designed by Luciano
Terms and Conditions Privacy Policy Cookies EU ODR platform
Cookies settings