FIRSTECH FTI-STK1 T-Harness for Subaru Key Instruction Manual
- June 17, 2024
- FIRSTECH
Table of Contents
FIRSTECH FTI-STK1 T-Harness for Subaru Key
Specifications
- Product: FTI-STK1
- Vehicle Compatibility: 2024 Subaru Crosstrek STD KEY AT (Canada)
- Required Accessories: Weblink Hub, ACC RFID1, Flash module
- Connection Type: Type 1 20-Pin CAN for CAN connections
- Immobilizer Type: Type B IMMO
- Pre-wired Parking Lights in harness
Product Usage Instructions
Installation
- Ensure the vehicle is turned off and key is removed from the ignition.
- Connect the required accessories (Weblink Hub, ACC RFID1) to the appropriate ports.
- Install the FTI-STK1 harness according to the vehicle’s wiring diagram.
Configuration
- Connect the white 2-pin connectors at marker [D] for Type 1 CAN connections.
- Connect the black and white 2-pin connectors at marker [C] for Type B IMMO connections.
- Follow RFID programming directions before programming the BLADE module.
Additional Notes
- Ensure all 2-pin connections are secured to the main harness body.
- Cut and insulate the red/white 2nd START output wire if not required.
FAQ
Q: What should I do if the Module LED flashes red during programming?
A: Different flashing patterns indicate different errors:
- 1x RED = Unable to communicate with RFID or immobilizer data.
- 2x RED = No CAN activity. Check the CAN wire connections.
- 3x RED = No ignition detected. Check the ignition wire connection and CAN.
- 4x RED = Required ignition output diode not detected.
Q: Is the Weblink HUB mandatory for installation?
A: Yes, the Weblink HUB is required for this installation process.
Vehicle Coverage and Preparation Notes
-
Covered vehicle use BLADE-AL-SUB9 firmware and the following required accessories, Weblink Hub & ACC RFID1.
Flash module, and update the controller firmware. Please follow the directions for RFID programming before attempting to program the BLADE module to the vehicle. -
CAN: Type 1 CAN connections are made using the 20-Pin BCM adapter and require connecting the white 2-pin connectors at marker [D] of the illustration.
-
Immobilizer: Type B IMMO requires connecting the black and white 2-pin connectors at marker [C] of the illustration.
-
Lights: Parking lights are pre-wired in the FTI-STK1 harness. Replace the green/white wire of the CM I/O connector with the pre-terminated green/white wire of the harness.
-
ACC-RFID1 (REQUIRED): SUB9 firmware does not provide immobilizer data, an ACC-RFID1 is therefore required for remote start
-
2nd START: The FTI-STK1 harness is pre-wired with a red/white 2nd START output (not required in TYPE 1), cut and insulate the provided wire to prevent short circuits when not used.
I/O Changes: None required
- Advisory 1: Program ACC-RFID1 before attempting to program the BLADE module to the vehicle.
- Advisory 2: Secure all 2-pin connections, both used and unused, to the main harness body.
Installation and Configuration Notes
- A REQUIRED ACCESSORY
- B ADAPTER REQUIRED
- C REQUIRED CONFIGURATION (TYPE B IMMO)
- D NO CONNECTION
- E NO CONNECTION
FEATURE COVERAGE
FTI-STK1 – AL-SUB9 – Type 1
2024 Subaru Crosstrek STD KEY(CA)
CARTRIDGE INSTALLATION
- Slide cartridge into unit. Notice button under LED.
- Ready for Module Programming Procedure.
MODULE PROGRAMMING PROCEDURE
-
For this installation, the Weblink HUB is required.
-
Remove OEM key 1 from keychain.
Place all other keyfobs at least 1 foot away from the Weblink HUB. Failure to comply may result in damage to other keyfobs or interfere with the keyfob reading process. -
Flash the module using the Weblink HUB. Follow the on screen instructions to complete the keyfob reading process.
WARNING:
Do not press the module -
programming button.
Connect power first. Connect module to vehicle. -
Using OEM key 1, turn key to ON position.
-
Wait, LED will turn solid BLUE for 2 seconds
-
Turn key to OFF position.
-
Module Programming Procedure completed.
Automotive Data Solutions Inc. © 2020
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>