FIRSTECH 2017 Hyundai Santa FE PTS Automatic Installation Guide

FIRSTECH 2017 Hyundai Santa FE PTS Automatic

Product Information

The product being discussed in this user manual is the Compustar Remote Start RSA-HK11A with hardware CM-DC3. This product is designed for use in a 2017 Hyundai Santa Fe PTS Automatic. The firmware version is RSA-HK11A and the document number is A520062. The user manual also provides information on the module connectors, technical notes, and T-harness/component locator.

Product Usage Instructions

The Compustar Remote Start RSA-HK11A is designed to be installed in a 2017 Hyundai Santa Fe PTS Automatic. To complete the installation process, some accessories may be required. It is recommended to visit the manufacturer’s website to see all the required accessories for your vehicle. The product can be used for remote start and keyless entry. The user manual provides information on the supported features,
including security system, comfort, and other functions that are defined by firmware. The product also includes automatic transmission, cut loop, battery – 2 pin white, drone – 4 pin gray, RF port – 4 pin blue, RPS sensor – 4 pin white, sensor 2 – 4 pin green, alarm LED – 2 pin white, temp sensor – 2 pin blue, programming button LED 2 (RS), FT-DAS – 4 pin red, and BLE – 4 pin yellow. It is important to note that a security plate may need to be removed to access smart key module connectors. A bolt extractor and a ratchet can be used to remove the plate’s tamper-proof screws. Included bolts can be used to reinstall the security plate if necessary. The T-harness/component locator provides information on how to locate the different components and connectors for the installation process.

FEATURE LIST

REMOTE START Supported

• Data Immobilizer Bypass (no key required) ✓
  Key Required for Immobilizer Bypass

• Takeover Available ✓
  No Takeover Available (shutdown on unlock or door open)

• 3x Lock Start from OEM Remotes ✓
  Data / MUX Parking Light Control – Constant

• Data / MUX / Hazard Parking Light Control – Flashing ✓

• Tach Monitoring ✓

• Hood Status ✓

• Brake Status ✓

• E-Brake Status ✓
  Glow Plug Status

• RAP Shutdown ✓

KEYLESS ENTRY Supported

• OEM Remotes Functional during RS ✓
• OEM RFID Entry Sensors Functional during RS ✓
• Door Lock ✓
• Door Unlock ✓
• Driver Door Priority Unlock ✓
• Trunk/Hatch Release ✓
• Power Liftgate ✓
  • Power Sliding Door (L)
  • Power Sliding Door (R)

SECURITY SYSTEM Supported

• Arm OEM Alarm ✓
• Disarm OEM Alarm ✓
• Aftermarket Alarm Control from OEM Remotes ✓
• Aftermarket Alarm Control from OEM RFID Entry Sensors ✓
• Door Status ✓
• Trunk/Hatch Status ✓

COMFORT Supported

• Rear Defrost Activation
• Heated Mirror Activation
• Heated Seat Activation
• Cooled Seat Activation
• Heated Steering Wheel Activation

MODULE CONNECTORS

CONNECTOR PINOUT

FUNCTIONS DEFINED BY FIRMWARE

FUNCTIONS DEFINED BY FIRMWARE

FUNCTIONS DEFINED BY FIRMWARE

IMPORTANT
A SECURITY PLATE MAY NEED TO BE REMOVED TO ACCESS SMART KEY MODULE CONNECTORS. USE A BOLT EXTRACTOR AND A RATCHET TO REMOVE THE PLATE’S TAMPER PROOF SCREWS. USE INCLUDED BOLTS TO REINSTALL SECURITY PLATE IF NECESSARY.

T-HARNESS / COMPONENT LOCATOR

HARDWIRE / COMPONENT LOCATOR

HARDWIRE / WIRING DIAGRAM

MODULE PROGRAMMING PROCEDURE

WARNING: All vehicle doors must be closed and locked prior to remote start sequence. When programming, only one key fob will be used. The other one must be located at least 10 feet away from the vehicle.

Set ignition to ON position.

Wait, LED 1 will turn solid GREEN for 2 seconds

Set ignition to OFF position.

START vehicle for 15 seconds.

Press and hold the brake pedal.

Press and release the module’s programming button.

Release the brake pedal.

Wait, LED 2 will flash GREEN

Module Programming Procedure completed.

TAKEOVER PROCEDURE

All vehicle doors must be closed and locked prior to remote start sequence.

Time restriction. Complete steps 2 to 5 within 45 seconds.

Press unlock on OEM or aftermarket remote or request switch.

Open driver door and enter vehicle.

Close driver door.

Press and release BRAKE pedal.

Take over procedure completed.

Failure to follow procedure will result in vehicle engine shutdown.

REMOTE STARTER ERROR CODES

REMOTE STARTER ERROR CODES: NOTES| PARKING LIGHT FLASHES| DIAGNOSTIC
---|---|---
I   WARNING: The following applies only when the parking lights are connected and supported by the system.

II   After a remote starter failure, the parking lights will flash three [3x] times followed by the error code. See table.

| 3 + 1| Tach is not programmed OR engine is already running.
3 + 2| Key is in ignition ON position.
3 + 3| Door is open.
3 + 4| Trunk is open.
3 + 5| Foot brake is ON.
3 + 6| Hood is open.
3 + 7| Loop is not cut.
3 + 8| No tach detected.
3 + 9| Vehicle movement detected (VSS).
3 + 10| System is in Valet Mode.
3 + 11| CAN communication failure
3 + 12| RS not synchronized. Start vehicle with OEM key for 15 sec before trying a new RS sequence.
3 + 13| Bypass problem.
3 + 14| Idle mode or takeover is not available on this vehicle.
3 + 15| Overheat protection.
REMOTE STARTER SHUTDOWN ERROR CODES: NOTES| PARKING LIGHT FLASHES| DIAGNOSTIC
---|---|---
I   WARNING: The following applies only when the parking lights are connected and supported by the system.
II   If the engine shuts down after a remote starter sequence use the query command from a compatible aftermarket
remote to display the shutdown error code. The parking lights will flash four [4x] times followed by the error code. See table.| 4 + 1| Engine tach signal was lost.
4 + 2| Emergency brake signal was lost.
4 + 3| Foot brake ON detected.
4 + 4| Hood open detected.
4 + 5| Tach over rev detected.
4 + 6| Glow plug timeout error.
4 + 7| Vehicle movement detected (VSS).
4 + 8| Check engine light ON.
4 + 9| Low fuel level.
4 + 10| Open door detected.
4 + 11| CAN communication failure during RS sequence.
4 + 12| RS not synchronized. Start vehicle with OEM key for 15 sec before trying a new RS sequence.
4 + 13| Bypass problem.
4 + 14| Idle mode or takeover is not available on this vehicle.
4 + 15| Overheat protection.
MODULE STATUS DURING:| **| LED STATUS| DIAGNOSTIC**
---|---|---|---
MODULE PROGRAMMING| | •| Flashing RED| Missing/wrong information from firmware or vehicle.

See firmware specific diagnostics, or contact technical support.

| •| Solid RED| Module waiting for more vehicle information. Programming incomplete.
| •| Flashing GREEN| Additional steps required to complete programming. Refer to install guide.
| •| Solid GREEN then OFF| Module programming completed successfully.
| o| OFF| No activity or module already programmed.
•| | 1 RED flash| No firmware on module. Connect to Weblink and flash device.
•| | 2 ORANGE flashes| Contact technical support.
•| | 3 ORANGE flashes| Module programming not completed.
•| | 4 ORANGE flashes| Contact technical support.
•| | 7 ORANGE flashes| Contact technical support.
•| | 8 ORANGE flashes| Loop not cut. Ensure loop is cut for automatic transmission. Reset and re-learn.
•| | 9 ORANGE flashes| Loop not cut. Ensure loop is cut for automatic transmission. Reset and re-learn.
•| | 10 ORANGE flashes| Boot loader update failed. Contact technical support.
•| | 11 ORANGE flashes| T-harness detection does not match install type selection in Weblink.
TACH PROGRAMMING| •| | Solid RED| Tach learn in progress.
•| | 1 GREEN flash| Tach signal programmed in analog.
•| | 2 GREEN flashes| Tach signal programmed in data.
•| | 3 RED flashes| No tach signal detected
•| | 4 RED flashes| System is in valet mode. Turn off valet mode to program tach.
•| | 6 RED flashes| Engine sensing set for ‘assumed start’. No tach programming required.
•| | 7 ORANGE flashes| Engine sensing not configured properly. Contact technical support.
MODULE STATUS DURING:| | LED STATUS| DIAGNOSTIC
---|---|---|---
REMOTE START SEQUENCE| •| | Flashing rapid RED| Remote start shutdown sequence.
•| | Flashing slow RED| Remote start shutdown error code. Contact technical support.
•| | Solid RED| Remote start crank delay.
•| | Flashing rapid GREEN| Remote start cycle in progress. Working correctly.
•| | 1 GREEN flash| Remote start initiated successfully.
•| | 3 GREEN flashes| Idle mode cycle in progress.
•| | 4 GREEN flashes| Turbo mode cycle in progress.
| •| Flashing GREEN| Remote start cycle in progress. Displays vehicle platform during runtime.
| •| Rapid GREEN flashing| Secure takeover initiated. Waiting to complete takeover after brake press.
TRANSMITTER PROGRAMMING| •| | Solid RED| Remote programming in progress, waiting for remote pairing.
•| | 1 GREEN flash| Remote programmed.
•| | 4 RED flashes| Shutdown remote starter before attempting remote programming.
•| | 5 RED flashes| Engine must be off before attempting remote programming.
•| | 6 RED flashes| System must be unlocked/disarmed before attempting remote programming.
•| | 7 RED flashes|

• LED 2 (RS) displays generic diagnostic codes specific to the remote start module. Orange LED flashes may appear red. ** LED 1 (Bypass) displays diagnostic codes specific to the firmware loaded on the module.
• Visit the programming diagnostics page for more information.

DOCUMENT NUMBER
A520062
REVISION DATE
20211218_204600
FIRMWARE
RSA-HK11A
HARDWARE
CM-DC3
ACCESSORIES
ATTENTION: TO COMPLETE THIS INSTALLATION SOME ACCESSORIES MAY BE REQUIRED. VISIT OUR WEBSITE TO SEE ALL THE REQUIRED ACCESSORIES FOR YOUR VEHICLE.

TERMS OF USE

Automotive Data Solutions Inc. (“ADS”) products are strictly intended for installation by Certified Technicians who are employed by a registered business specialized in the installation of automotive aftermarket electronics products. Prior to beginning installation of an ADS product in a vehicle, it is the Certified Technician’s responsibility to review the most current Product Guide, Install Guide and vehicle-specific notes available in Weblink®. ADS is not responsible for any damages whatsoever, including but not limited to any consequential damages, incidental damages, damages for loss of time, loss of earnings, loss of profit, commercial loss, loss of economic opportunity and the like that may or may not have resulted from the use, misuse, improper installation or operation of its products. ADS reserves itself the right to suspend any Weblink® account without notice and decline to offer technical support to non-Certified Technicians, noncompliant Certified Technicians or end users.

References

• Myfirstech - Home

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>