LOREX W891UA 4K Dual Lens Wi-Fi Security Camera User Guide
- June 17, 2024
- Lorex
Table of Contents
W891UA 4K Dual Lens Wi-Fi Security Camera
W891UA
4K Dual-Lens Wi-Fi Security Camera
Quick Start Guide
What’s Included
Note: Based on 1 camera
4K Dual-Lens Wi-Fi Security Camera
Mounting Template
Anchors & Screws (8×)
Power Adapter
Cable Clips (4×)
Pre-Installed 32GB MicroSD Card
Tools Needed
- Drill
- Screwdriver
Smart Security LED Indicators
Operating correctly
Ready for network connection
Device resetting
Network connection failed*
Firmware update in progress
- Try resetting the device by holding down the reset button until you hear the audio prompt.
Overview
- Microphone
- Dual Camera Lens
- Smart Security Lighting
- IR Lights
- Warning Lights
- Camera Adjustment Screw
- Mounting Bracket Adjustment Screw
- Mounting Bracket
- QR Code
- Reset Button
- MicroSD Card Slot
- Speaker & Siren
- Cable Notch
Camera Placement Tips
Height: Install your camera at a height of 10 ft (3 m) above the ground.
Angle: Angle your camera outwards by 15°. Avoid angles greater than 30°.
Distance: Place your camera within 22-65 ft (7-20 m) of points of
interest.
Camera Mounting
-
Place the provided Mounting Template onto the desired location. Ensure an outlet is nearby, and keep in mind the
cable length. -
Using a drill, drill through all 3 mounting screw holes on the template.
Note: Drill a hole through the center of the template for your camera’s cable if you plan to run it through the
mounting surface. If you are running the cable along a wall/ceiling, make sure to pass the cable through the cable
notch. -
Using a Phillips-head screwdriver and the provided Mounting Screws, secure the Mounting Bracket to the surface.
Optional: If you are mounting your camera into drywall, use the provided anchors. -
Connect your camera’s cable to the Power Adapter and plug into a nearby outlet.
-
(Optional) Use the provided Cable Clips and Screws to neatly secure your camera’s cable to the wall.
-
Adjust the angle of your camera:
• Loosen the Camera Adjustment Screw to rotate your camera downwards and sideways, then tighten to
secure it in place.
• Loosen the Mounting Bracket Adjustment Screw to rotate your camera and bracket clockwise or counterclockwise
around the base, then tighten to secure it in place.
• Tip: For a sideways orientation of your camera you must rotate the mounting bracket by 90°, then rotate the
camera by 90°, and then point your camera to the desired side. -
Remove the vinyl film from the camera lens once your installation is complete.
Camera Adjustment Screw
Mounting Bracket Adjustment Screw
Lorex App Setup
AQs
How do I activate the smart motion detection features?
1. Open the Lorex app and tap above the camera’s thumbnail.
2. Tap Motion Detection Settings, and then to activate Motion Detection.
3. Tap Smart Detection Settings, and then to activate the type of smart
motion detection you want to use.
How do I customize Motion Zones™?
1. Open the Lorex app and tap above the camera’s thumbnail.
2. Tap Motion Detection Settings, and then to activate Motion Detection.
3. Tap Motion Zones™, and then the type of smart motion detection you want to
customize a motion detection area
for.
How do I activate Deterrence Lights and/or Smart Security Lighting when
smart motion is detected?
1. Open the Lorex app and tap above the camera’s thumbnail.
2. Tap Light Settings > Activate Light on Smart Motion.
3. Tap on the type of smart motion detection you are using, and then to
activate either Deterrence Light and/
or Smart Security Lighting.
How do I turn Smart Security Lighting off?
1. Open the Lorex app and tap above the camera’s thumbnail.
2. Tap Light Settings > Smart Security Light Modes.
3. Tap to deselect the mode, and then Set.
Need Help?
For additional support material, scan the below QR code or visit:
Register Your Product
Please see our full Terms of Service and Limited Hardware Warranty Policy at: lorex.com/warranty
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and (2) This device must
accept any interference
received, including interference that may cause undesired operation.
lorex.com
help.lorex.com/W891UASeries
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>