legrand WNAR153 Adorne 15A Smart Outlet Instruction Manual
- June 8, 2024
- Legrand
Table of Contents
adorneTM
WNAR153/WNAR203 Smart Outlet with Netatmo, 3-Module, 15A/20A, 125VAC
Installation Instructions
Catalog Number(s)
WNAR153
WNAR203
WNAR153 Adorne 15A Smart Outlet
adorne ™ Smart Outlet 15A Prise intelligente Adorne adorne™ Smart Outlet
20 ATomacorriente inteligente 20A adorne ™
Wall plate sold separately
REGULATORY INFORMATION
FCC NOTICE: This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesirable operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna
- Increase the separation between the equipment and receiver
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
- Consult the dealer or an experienced radio/TV technician for help
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 90 mm between the transmitter’s radiating structure(s)
and the body of the user or nearby persons.
NOTE: Any changes or modifications to this device that are not expressly
approved by the manufacturer will void the warranty and the user’s authority
to operate the quipment. Contains FCC ID: 2AU5D2982057
IC NOTICE: This device complies with Industry Canada license-exempt RSS
standards. Operation is subject to the following two conditions:
- this device may not cause interference; and
- this device must accept any interference, including interference that may cause undesired operation of the device.
RF EXPOSURE STATEMENT: This equipment meets the SAR evaluation limits
given in RSS-102 Issue 5 requirements at the minimum separation distance of 90
mm to he human body.
Note: Any changes or modifications to this device that are not expressly
approved by the manufacturer, will void the warranty and the user’s authority
to operate the equipment.
IC: 25764-982057
HVIN: 982057
For more information and helpful how-to videos, visit
www.adornemyhome.com/install.
INSTALLATION INSTRUCTIONS
Please read these instructions completely before you begin. This adorne™
device is designed for installation in standard electrical boxes. However,
some of the installation methods vary slightly from traditional methods. If
you do not understand these instructions or are unsure of your abilities, seek
the assistance of a qualified electrician.
Use only with Legrand adorne ™system.
WARNING
To prevent severe shock or electrocution, always disconnect power at the
service panel before beginning work.
When replacing existing outlets, label wires before disconnecting. Disconnect
old outlet.
Neutral (White)
Hot (Black)
Ground (Bare)
If necessary, cut wires and strip insulation using stripping guide on back of
outlet.
WARNING
Failure to connect the ground wire will result in an unsafe installation that
could lead to personal injury.
Connect new smart outlet as shown. Make sure the terminal holes are
clear. Insert wires into terminals and torque terminal screws to 14-16 inch-
pounds. Do NOT over-tighten.
- Connect the WHITE neutral wire(s) in the box to the “WHITE” terminal on the outlet
- Connect the HOT wire in the box to “LINE HOT” terminal on the outlet
- If a LOAD wire is present in the box, connect it to the “LINE HOT” terminal on the outlet
- Connect the ground wire in the box to the GROUND terminal on the side of the outlet
This outlet can be optionally wired to control downstream outlets. For more information, please see the resources section for this product on Legrand.us website.
WARNING: Do not pair different size wires in the same terminal. If you have different size wires, use a wire nut to add a 6 inch pigtail of the same gauge wire to the smaller gauge wire.
Same size. Different size with pigtail. Different size.
Set Up Your System
a. Download and launch the Legrand Home + Control app. The app is available on
the App Store or on Google Play.
b. Connect your smart device to your home network by following the step by
step instructions in the app.
c. Use the app to control your smart device.
LED Indicator Light Explanation
| State of Light | Behavior of Device |
|---|---|
| Solid Red | Factory reset, not in network. |
| Blinking Green | Device is attempting to connect to the network mode |
| Solid Green | Device in network, temporarily open |
Getting to Know Your Outlet
| Item | Name | Description |
|---|---|---|
| 1 | Indicator Light | Indicates operation. See “Indicator Light Explanations” |
for detail
2| On/Off Button| Turns the controlled outlet On or Off
3| Controlled Outlet| Outlet controlled by On/Off button and app
4| Uncontrolled Outlet| “Always on” outlet
5| EZ Button| Use to connect the device to
Reset to Factory Default
Deleting a device from the app will reset it to factory defaults. To manually
reset the device to factory defaults, press and hold the EZ button for 10
seconds until you see the LED blink red, then release. The LED will change to
solid red when the reset is complete.
Due to ongoing product improvements, Legrand reserves the right to change
specifications without notice. For the most recent instruction sheets or more
information on this product, please see this link or scan the QR code:
https://www.legrand.us/p/wnar153w1
https://www.legrand.us/p/wnar203w1
https://www.legrand.us/p/wnar153w1| https://www.legrand.us/p/wnar203w1
Snap wall plate to frame. There are three click-stops to adjust the fit of the wall plate to the device and the wall.
NOTE: To remove wall plate, insert a small, flat screwdriver in notches
on wall plate and twist gently to pry from frame.
Never apply cleaner directly to the dimmer or wall plate. Apply to a soft
cloth and use cloth to remove any smudges from the product.
Technical Assistance:
877-295-3472
www.adornemyhome.com/install
LIMITED TWO-YEAR WARRANTY
Limited two-year warranty information for adorne products is available at
www.legrand.us/adorne/warranty.
Limited warranty information for adorne™ products may also be obtained free of
charge by sending a written request, along with your proof of purchase
(including purchase date), to: Legrand Attn: adorne Customer Service/Warranty
Department 50 Boyd Avenue Syracuse, NY 13209 No: 341334 – 08/21 © Copyright
2021 Legrand All Rights Reserved.
60 Woodlawn Street
West Hartford, CT 06110
1.877.BY.LEGRAND
(295.3472)
www.legrand.us
570 Applewood Crescent
Vaughan, ONT L4K 4B4
905.738.9195
www.legrand.ca
Documents / Resources
|
legrand WNAR153 Adorne 15A Smart
Outlet
[pdf] Instruction Manual
WNAR153 Adorne 15A Smart Outlet, Adorne 15A Smart Outlet, WNAR153 Smart
Outlet, Smart Outlet, Outlet, WNAR153, WNAR203
---|---
References
- Legrand US | Delivering and Managing Power, Light, and Data
- Search Results Page
- Legrand US | Delivering and Managing Power, Light, and Data
- The adorne® Collection | Legrand
- adorne® Warranty ⎸Legrand
- adorne 15A Smart Outlet with Netatmo │ Legrand
- adorne 20A Smart Outlet with Netatmo ǀ Legrand
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>