LOREX Halo Series 4K IP Dual Lens Security Camera User Guide

LOREX Halo Series 4K IP Dual Lens Security Camera

What’s Included

Note: Based on 1 camera

Overview

Bullet I E91 DAB

1. Cable Notch
2. Adjustment Screw
3. Speaker
4. MicroSD Card Slot
5. Reset Button
6. IR (Infrared) Light
7. Camera Lens
8. Smart Security Lighting
9. Warning Lights
10. Microphone

Dome I E91 ODD

1. Adjustment Screw
2. Smart Security Lighting
3. Microphone
4. IR (Infrared) Light
5. Reset Button
6. Speaker
7. Camera Lens
8. Warning Lights
9. Cable Notch
10. MicroSD Card Slot

Camera Placement Tips

• Take into consideration what you want to monitor and where is the best coverage area.
• Place your camera close to the area of interest.
• Point the camera where there is the least amount of obstructions (i.e. tree branches).
• Install the camera in a location that is difficult for thieves and vandals to reach.

Mounting Your Camera

Test your camera prior to selecting a permanent mounting location,

Bullet I E910AB

1. Use the mounting template to drill holes for screws, then insert the drywall anchors. Drill a hole for the camera’s cable if you plan to run it through the mounting surface.
2. Use the screws to mount the camera base to the surface. If you are running cables along a wall/ceiling, make sure to pass the cable through the cable notch.
3. Feed the camera’s cable through the camera base, then connect the cables (see page 14).
4. Loosen the adjustment screw and position your camera as needed, then tighten to secure it in place.
5. Remove the vinyl film from the camera lens once your installation is complete.

Dome/ E910DD

1. Use the mounting template to drill holes for screws, then insert the drywall anchors. Drill a hole for the camera’s cable if you plan to run it through the mounting surface.
2. Use the Allen key to loosen the camera’s adjustment screw, then remove the dome cover from the camera base.
3. Use the screws to mount the camera base to the surface. If you are running cables along a wall/ceiling, make sure to pass the cable through the cable notch.
4. Feed the camera’s cable through the camera base, then connect the cables (see page 14).
5. Angle your dome camera, then use the Allen key to tighten the dome cover firmly onto the camera base.
6. Remove the vinyl film from the camera lens once your installation is complete.

Connecting Your Camera

Connect your camera directly to your recorder using the camera’s Ethernet extension cable.

Weather-resistant Cap

Twist the Ethernet extension cable’s pre-attached weather-resistant cap securely onto your camera’s Ethernet connector. If exposed to regular precipitation, seal the cap with silicone and electrical tape.

Need Help?
For related support, scan the QR code or visit

Register Your Product
Please see our full Terms of Service and Limited Hardware Warranty Policy at: lorex.com/warranty

Safety Precautions

• Follow all instructions for safe use and handling of the product.
• Use the camera within given temperature, humidity and voltage levels noted in the camera specifications.
• Do not disassemble the camera.
• Do not point the camera directly at the sun or a source of intense light.
• Periodic cleaning may be required. Use a damp cloth only. Do not use any harsh, chemical-based cleaners.
• The supplied cable is rated for surface mounting only (Non-UL). Cables for in-wall and floor-to-floor installations are sold separately (CMR type). These and other cables are available at lorex.com.
• It is recommended to connect the camera to the NVR or an external PoE switch. If using a power adapter with this camera, a REGULATED power supply is REQUIRED (not included). Use of a non-regulated, non-conforming power supply can damage this product and void the warranty.

Dislcaimers

• Use the camera only with compatible Lorex recorders. For a full list, visit lorex.com/compatibility.
• Not intended for submersion in water. Installation in a sheltered location is recommended.
• This camera includes an Auto Mechanical JR Cut Filter. When the camera changes between Day/Night viewing modes, an audible clicking noise may be heard from the camera. This clicking is normal, and indicates that the camera filter is working.
• Audio recording and/or face recording without consent is illegal in certain jurisdictions. Lorex Corporation assumes no liability for use of its products that does not conform with local laws.

Copyright© 2023 Lorex Technology Inc.
As our products are subject to continuous improvement, Lorex reserves the right to modify product design, specifications and prices, without notice and without incurring any obligation. E&OE. All rights reserved.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>