LOREX Halo Series H20 4K IP Dual Lens Security Camera User Guide
- June 1, 2024
- Lorex
Table of Contents
Halo Series
Lorex H20
E87IAB
Quick Start Guide
lorex.com
Safety Precautions
- Follow all instructions for safe use and handling of the product.
- Use the camera within given temperature, humidity and voltage levels noted in the camera specifications.
- Do not disassemble the camera.
- Do not point the camera directly at the sun or a source of intense light.
- Periodic cleaning may be required. Use a damp cloth only. Do not use any harsh, chemical-based cleaners.
- The supplied cable is rated for surface mounting only (NorUL). Cables for in-wall and floor-to-floor installations are sold separately (CMR type). These and other cables are available at lorex.com.
- It is recommended to connect the camera to the NVR or an external PoE switch. If using a power adapter with this camera, a REGULATED power supply is REQUIRED (not included). Use of a nor-regulated, non-conforming power supply can damage this product and voids the warranty.
Disclaimers
- Use the camera only with compatible Lorex recorders. For a full list, visit lorex.com/compatibility.
- Not intended for submersion in water. Installation in a sheltered location recommended.
- This camera includes an Auto Mechanical IR Cut Filter. When the camera changes between Day/Night viewing modes, an audible clicking noise may be heard from the camera. This clicking is normal, and indicates that the camera filter is working.
- Audio recording and/or face recording without consent is illegal in certain jurisdictions. Lorex Corporation assumes no liability for use of its products that does not conform with local laws.
What’s Included
Note: Based on 1 camera
Tools Needed:
- Drill
- Screwdriver
Overview
- Microphone
- Dual Lens
- Smart Security Lighting
- IR (Infrared) Light (x3)
- Warning Light (x2)
- Adjustment Screw (x2)
- Camera Base
- MicroSD Card Slot
- Reset Button*
- Speaker & Siren
- Cable Notch
*Press and hold for 10 seconds 
Camera Placement Tips
Important! Ensure the mounting surface can support at least 3 times your
camera’s weight.
Location: Place your camera in a wide, open space. Avoid placing it near
any obstructions.
Height: Install your camera at a height of 10 ft (3 m) above the ground.
Angle: Angle your camera outwards by 15°. Avoid angles greater than 30°.
Distance: Place your camera within 22-65 ft (7-20 m) of points of
interest.
Camera Mounting
- Use the mounting template to drill holes for screws, then insert the drywall anchors. Drill a hole for the camera’s cable if you plan to run it through the mounting surface.
- Use the screws to mount the camera base to the surface. If you are running cables along a wall/ceiling, make sure to pass the cable through the cable notch.
- Feed the camera’s cable through the camera base, then connect the cables (see page 12).
- Loosen the adjustment screws and position your camera as needed, then tighten to secure it in place.
- Remove the vinyl film from the camera lens once your installation is complete.
Camera Connection
Connect your camera directly to your recorder using the camera’s Ethernet
extension cable.
Weather-resistant Cap
Twist the Ethernet extension cable’s pre-attached weather- resistant cap
securely onto your camera’s Ethernet connector.
If exposed to regular precipitation, seal the cap with silicone and electrical
tape. Need Help?
For related support, scan the QR code or visit:
Register Your Product
Please see our full Terms of Service and Limited Hardware Warranty Policy at: lorex.com/warranty
Copyright © 2023 Lorex Technology Inc.
As our products are subject to continuous improvement
Lorex reserves the right to modify product design,
specifications and prices, without notice and without incurring any
obligation.
E&OE. All rights reserved.
lorex.com
help.lorex.com/E87IAB
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>