LOREX U855AA Series 4K Battery Operated Camera User Guide

U855AA Series 4K
Battery Operated Camera
User Guide

U855AA Series
4K Battery-Operated Camera

What’s Included

Tools Needed

• Drill
• Screwdriver

Camera Overview

1. Antenna
2. Warning Light
3. Light Sensor
4. Camera Lens
5. Microphone
6. IR Light
7. Fastener
8. Adjustment Ring
9. Battery Release Tabs (x2)| 10. PIR Sensor
11. Pairing Button
12. MicroSD Card Slot
13. Speaker
14. Power Port
15. Locking Screw
16. Battery Charging Indicator
17. Mounting Plate Slots
---|---

Camera Charging

The camera battery comes partially charged (due to safety regulations). Please, fully charge the battery before use and setup. You can charge the battery inside or outside of the camera.

1. Pull and remove the sticker on the camera battery.
2. Lift the Power Port cover, connect your camera to a micro-USB cord and adapter, and then plug into an outlet.
3. Insert the fully charged battery into the bottom of the camera.
   Note: You will hear a ‘click’ when the battery is properly inserted. If you do not here a click, remove the battery by squeezing the release tabs, and then re-insert.

Battery Charging Indicator

| Fully charged| | Charging
---|---|---|---

Battery Duration

Camera Pairing

1. Download Lorex Cirrus app.https://app.lorex.com/cirrus/download
2. Select your recorder from the list.
3. Tap any free channel with a (app) icon.
4. (Optional) From the NVR display, tap any free channel marked with a icon.
5. Tap Pair.
6. If you do not see your cameras on the NVR display or are adding additional cameras, press and hold the pairing button until the red LED lights stop flashing, then release the pairing button.

Note:

• Ensure that your Wi-Fi cameras and your recorder are connected to the same network.
• In the app, the message ‘Pairing success!’ will appear. If you do not see this message, repeat steps 2 & 3.
• On the NVR, you will have 30 seconds to pair the camera after you press and hold the pairing button on the back of the camera.

Camera Mounting

1. Position the mounting bracket to the desired mounting location.

2. Mark holes through the Mounting Bracket.

3. Using the included drill bit, drill holes where marked.

4. Using the included screwdriver, secure the Bracket with the provided Mounting Screws.
   Optional: If you are mounting the camera into drywall, use the provided drywall anchors.

5. Align the camera’s Mounting Plate Slots to the tabs in the Mounting Bracket. Push in and slide down to secure in place.

6. Insert the Fastener Screw through the Fastener on the top of the camera and Mounting Bracket, then tighten with the screwdriver.

7. Tighten the pre-installed Locking Screw using the screwdriver. Note: To remove the camera battery in the future, loosen the locking screw.

8. Turn the adjustment ring counter-clockwise to loosen and reposition the camera. Turn the adjustment ring clockwise to secure the desired position.

FAQs

Preguntas frecuentes

How do I extend the battery life?
Note: Battery life is dependent on placement, settings, frequency and length of events, and ambient temperature.
a. Select Person Detection.
In the Lorex Cirrus app, select the camera channel > tap > tap Motion Detection Settings > select Person.
b. Reduce the Distance Setting to less than 50% distance.
In the Lorex Cirrus app, select the camera channel > tap > tap Motion Detection Settings > tap Distance Setting > Slide the bar to the desired percentage.
c. Disable the deterrence light.
From the NVR, right-click > click > click Setup > click Alarm > click Deterrence > click and drag to  deselect the schedule.  means enabled; means disabled.
d. Create an activity zone (Mouse & display setup required).
From the NVR, right-click > click > click Setup > click Alarm > from the Area field click Setup.
Why is my video not clear, delayed, or lower in quality?
The camera is too far from the NVR. Place the NVR in a more central location or move the cameras closer. Video quality is dependent on your Wi-Fi network strength, the number of devices on your network etc.,
How do I enable continuous recording?

1. The camera must be connected to continuous power. To purchase the cable and adapter (ACPWF1), go to lorex.com.
2. From the NVR, right-click > click > click Setup > click Camera > from the Recording Time drop-down menu,  select Continuous.
   For more NVR configurations, download the Manual at help.lorex.com/L8559Series.

Need Help?

For the additional support material, scan the below QR code or visit:

https://help.lorextechnology.com/series/l8559series

Register Your Product

Please see our full Terms of Service and Limited Hardware Warranty Policy at: lorex.com/warranty
** This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference  that may cause undesired operation.
Copyright © 2023 Lorex Technology Inc.**
As our products are subject to continuous improvement, Lorex reserves the right to modify product design, specifications and prices, without notice and without incurring any obligation. E&OE. All rights reserved.

References

• Security Cameras - Home Security Camera Systems | Lorex

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>