BRIZO RP103317 Bilateral Steam Head Instruction Manual

RP103317 Bilateral Steam Head

113091 RP103317p BILATERAL STEAM HEAD
INSTALLATION

Model Number: ____
Date of Purchase: ____
Register Online www.brizo.com/customer-support/product- registration
To reference replacement parts and access additional technical documents and product info, visit www.brizo.com

1-800-355-6478
www.brizo.com/customer-support/contact-us
Read all instructions prior to installation.
CAUTION
Failure to read these instructions prior to installation may result in personal injury, property damage, or product failure. Manufacturer assumes no responsibility for product failure due to improper installation.
You may need: IMPORTANT: To use the bilateral steam head, make sure the steam room wall studs are exposed to allow for proper installation. If the walls are fully finished and studs are not accessible, please use a different type steam head.
NOTE: For maximum comfort the bilateral steam head should always be located as far from the seating area as possible.

• The bilateral steam head location should be 12” to 18” above the shower floor or 6” above the rim of the bathtub, as far from the seating area as possible. Do NOT install the steam head directly below the user control. For optimum performance, install the steam head on the wall opposite or adjacent and as far as possible from the user control.

• Rough in the steam line using a minimum of a ¾” copper or brass pipe. Do NOT use black iron or galvanized pipe as it will rust and discolor the wall of the steam room. Do NOT use CPVC or any plastic type pipe, fitting or water type line as the steam pipe.

• Place the bilateral steam head between wall studs (See Figure 2). Make sure that the front lip is placed in such way that it will be flush with the final wall material such as tile or stone (See Figure 4). If you are uncertain of the tile/stone thickness at the time of install, the front lip of the steam head may be slightly recessed back into the wall but must NOT be placed behind backer board and cannot protrude past front of tile (See Figure 3).

• Make sure the bilateral steam head is level, left to right and front to back (See Figure 2).

• Secure the bilateral steam head to wall studs using 8 screws or nails.

• Connect the ¾” copper or brass pipe to the bilateral steam head.

• Remove the front face cover by sliding it out of the bilateral steam head.

• Proceed with steam room construction by insulating the walls and installing backer board onto the wall. Make sure to leave a proper size cutout in the backer board for the bilateral steam head. Do NOT leave a large gap between the backer board and the bilateral steam head.

• Apply supplied sealant between the backer board and the outer edge of the bilateral steam head (See Figure 3).

• Complete the wall construction with thinset and tile/stone. Make sure to leave a proper size cutout in the tile/stone for the bilateral steam head. Do NOT leave a large gap between the tile/stone and the bilateral steam head.

• Apply supplied sealant between the tile/stone and the outer edge of the bilateral steam head (See Figure 3).
  NOTE: Make sure there are absolutely no air gaps between the outer edges of the bilateral steam head and the final wall material. If air gaps are left, steam will leak between wall construction and cause water damage to foundation.

• Insert front face cover back into the bilateral steam head. Push it in until it makes contact with the wall.

• Apply dabs of supplied sealant between the left and right edges of the front face cover and the wall tile/stone to make sure the cover does not slide out (See Figure 4).
  NOTE: A single bead of sealant can fill gaps up to 1/4”. If the gap is slightly larger than this, fill it in two steps. First place a bead of sealant deeper into the gap, but not flush with surface. Wait until the sealant is completely cured before coming back to run a second bead on top of the first bead (See Figure 3).

• Cure time of the supplied sealant: 1/4” gap = 5 days, 1/2” gap = 10 days.
  

Limited Warranty on Brizo® Steam Bath and Steam Shower Products
Applicable to products purchased and installed in the USA and Canada

Residential Steam Bath Generators : Brizo Kitchen and Bath Company (“Brizo”) warrants to the original consumer purchaser that the parts (except for electronic parts) of its residential steam bath generator purchased from authorized Brizo sellers will be free from defects in materials and workmanship for as long as the original consumer purchaser owns the home in which the steam bath was originally installed. This lifetime limited warranty does not apply to residential steam bath generators that are used in commercial applications (as defined herein).
Residential Electronic Parts, Controls, Spa Options and Accessories:
Brizo warrants to the original consumer purchaser  that the electronic parts of its steam bath generator and its controls, spa options and accessories purchased from authorized Brizo sellers will be free from defects in materials and workmanship for a period of two (2) years from the date that the product is received by the original consumer purchaser or their authorized representative (installation contractor, etc.). This two-year limited warranty does not apply to controls, spa options, electronic parts and accessories that are used in commercial applications (as defined herein).
Commercial Warranty:
For the purposes of this warranty the term “commercial application” refers to installation in any setting in which the product is not being used for personal household use, including, but not limited to, hospitality applications, day spas and short-term and long-term rentals.
Brizo warrants that the parts (including electronic parts) of its steam bath generators (including steam bath generators with model numbers beginning with 8GE that are 7.5kW-15kW), equipment, controls, electronic parts, spa options and accessories purchased from authorized Brizo sellers and used in a commercial application will be free from defects in materials and workmanship for a period of one (1) year from the date that the product is received by the original purchaser or their authorized representative (installation contractor, etc.).
What We Will Do:
Brizo will, at its option, repair or replace, free of charge, any part that proves defective in material and/or workmanship under normal installation, use and service during the applicable warranty period as stated above.
Brizo may elect to refund the purchase price. Replacement parts are subject to availability and may differ from those originally supplied.
For residential applications, two (2) years following the date that the product was received by the original consumer purchaser or their authorized representative (installation contractor, etc.) and with prior approval by Brizo, Brizo will pay for labor for repair/replacement associated with warranty coverage. Thereafter, Brizo will not pay for labor associated with removal/repair/replacement of products covered by this warranty.
For commercial applications, Brizo will, with prior approval by Brizo, pay for labor associated with warranty coverage for ninety (90) days from the date that the product is received by the original purchaser or their authorized representative (installation contractor, etc.). Thereafter, Brizo will not pay for labor associated with removal/repair/replacement of products covered by this warranty. These are the consumer’s exclusive remedies.
What Is Not Covered:
Because Brizo is unable to control the quality of Brizo products sold by unauthorized sellers, unless otherwise prohibited by law, this warranty does not cover Brizo products purchased from unauthorized sellers. This warranty does not cover damage caused by improper or negligent installation or use. Provided that Brizo is paying the cost of the labor under the terms above, this warranty does not cover repairs attempted by any person other than an authorized Brizo agent and shall be limited to the repair or replacement of defective parts by Brizo or its authorized agent.
This warranty is void if any of the following should occur:

• The use of the product for an unintended application, including a commercial application for all products except those products for which a commercial application is appropriate.
• Failure to follow instructions, including care, cleaning and usage instructions, provided in the product’s owner’s manual.
• The product’s serial number has been altered or removed.
• The product is modified in any manner which Brizo concludes, after its inspection, affects the reliability of the product.
• The product has been improperly repaired by anyone not specifically designated or authorized by Brizo.
• The product is damaged because it is not operated or installed in accordance with supplied instructions.
• The product is installed outdoors.
• The product is installed in a moist and/or humid area with unconditioned air or temperatures that exceed 104 degrees Fahrenheit.
• The product is damaged due to freezing.
• The product is damaged by acts of God.

How to Make a Warranty Claim:
To obtain warranty repair or replacement, contact Brizo at: 800-355-6478 or steamprodserv@brizo.com to receive an RGA# (Return Goods Authorization number) which must be on the carton that is returned via UPS Ground or equivalent. Proof of purchase (original sales receipt showing purchase date) identifying the model and serial number and documentation of the date of receipt of the product by the original purchaser or their authorized representative (installation contractor, etc.) must accompany all warranty claims.

Limitation on Duration of Implied Warranties:
Please note that some states/provinces (including Quebec) do not allow limitations on how long an implied warranty lasts, so the below limitations may not apply to you. TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, ANY IMPLIED WARRANTY, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND OF FITNESS FOR A PARTICULAR PURPOSE, IS LIMITED TO THE  STATUTORY PERIOD OR THE DURATION OF THIS WARRANTY, WHICHEVER IS SHORTER.
Limitation of Special, Incidental or Consequential Damages:
Please note that some states/provinces (including Quebec) do not allow the exclusion or limitation of special, incidental or consequential damages, so the below limitations and exclusions may not apply to you. TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THIS WARRANTY DOES NOT COVER, AND BRIZO SHALL NOT BE LIABLE FOR, ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES WHETHER ARISING OUT OF BREACH OF ANY EXPRESS OR IMPLIED WARRANTY, BREACH OF CONTRACT, TORT,  OR OTHERWISE.
Additional Rights: This warranty gives you specific legal rights, and you may also have other rights which vary from state/province to state/province. This is Brizo’s exclusive written warranty and the warranty is not transferable.

Model Number: ____
Date of Purchase: ____
Register Online
www.brizo.com/customer-support/product-registration
EP103314p & EP103315p
STEAMBATH CONTROL INSTRUCTIONS

To reference replacement parts and access additional technical documents and product info, visit www.brizo.comImage is for reference only.

1-800-355-6478
www.brizo.com/customer-support/contact-us
Read all instructions prior to installation.
CAUTION
Failure to read these instructions prior to installation may result in personal injury, property damage, or product failure. Manufacturer assumes no responsibility for product failure due to improper installation.

IMPORTANT: “Steam bath important safety instructions” publication 114317 includes a warning label that the contractor must install on the wall near the entrance to the steam room in a highly visible location. This label and its additional safety information are packaged with the generator packaging containing the installation instructions. If it is lost or missing contact: customer support (1-800-394-6478) for replacement instructions. This publication, along with all documents, must be left with the owner.

Control Features

1. Temperature Display: The digital readout displays the ambient temperature, set point and cycle time, system status, and diagnostic error codes.
2. Steam Icon: When illuminated, the steam cycle is running.
3. Water Icon: When steam shower is not in use, the blue water icon indicates the RapidMist feature is on. This is also illuminated during a steam bath cycle.
4. Menu button: Used to change cycle time, turn *RapidMist on or off, and switch between ºF and ºC. When steam is off, pressing this button will toggle between these settings. The settings are changed with the up/down arrow buttons.
5. Stop button: Pressing this button stops the current steam cycle and the Menu mode.
6. User 1 button: Starts the user one cycle and is the up function when changing Menu settings. Pressing this button while in a cycle will change the temperature and remaining time left on that cycle.
7. User 2 button: Starts the user two cycle and is the down function when changing Menu settings. Pressing this button while in a cycle will change the temperature and remaining time left on that cycle.

IMPORTANT: This control must be installed inside the steam room for proper operation of the system.
Cleaning instructions : Use a damp cloth and mild soap. Do NOT use abrasive cleaners which might scratch the surface or the base of the control.

• RapidMist option is only available when connecting to a 8GE-TSG series steam generator. RapidMist is a preheat function that keeps the water heated for quick starts.
  EP Digital Temperature Control

Installation

1. Pre-Installation – Control Location
   a. The Control must be installed inside the steam room and not above the steam head. For convenience the recommended height from the floor is four feet. Provide a 1½” hole in the wall at this location (see Figure 1).
   IMPORTANT: Multi-conductor cable must be installed so that the end will not be buried inside the wall. The unit will not operate unless the control is installed.

2. Electrical Rough-in
   a. Locate the multi-conductor cable. Carefully route the multi-conductor control cable from the steam generator to the control located inside the steamroom (see Figure 1). Route multi-conductor cable through a ¾” conduit to protect the cable from damage.

3. Control and Cable Installation
   a. Locate the previously installed cable and black plastic strain relief clamp which is in the control packing box. Locate the knockout on the steam generator for the control cable (see Figure 2).
   b. Place strain relief around cable about seven inches from the end and insert into the hole. Remove the protective covering labeled “Remove Before Installation” from the modular jack found on the PC board.
   c. Remove the protective cap from the multi-conductor cable plug. Connect the cable to the modular jack.
   d. Close and secure generator cover.
   e. Locate Telco Jack at female coupler, on back of the control. Remove the protective covering labeled “Remove Before Installation”.
   Remove protective cap from cable and plug into jack. Check that the orientation of the plug properly aligns with the jack. A snap will indicate the plug is installed correctly (see Figure 3).
   WARNING
   Test the control for operation before continuing on to the next step.
   f. Peel adhesive liner from back of the control. Apply the control to the wall. Press firmly and hold for a few seconds.
   g. After the control is in place, apply silicone (supplied) around the control to form a watertight seal (see Figure 3).

Operating Instructions

Operation: Make sure the water and power are turned on. Simply press User 1 or User 2 button to begin the cycle. Press the Stop button to end the cycle. After a cycle is started it will take a few minutes for the Steam Generator to heat up and begin producing steam. This time will be less if the RapidMist has been turned on. During operation the display will show the ambient temperature.To view the remaining cycle time, press the Menu button.
Programming: Adjustments can be made to temperature and cycle time while a cycle is started. When the temperature is displayed, the set temperature can be viewed or changed by momentarily pressing the up or down button. Temperature adjustments made when User 1 cycle is started will be saved to User 1 and likewise for User 2. All changes made to the temperature control are stored in memory until changed again. The temperature range is 60°F to 125°F (16°C to 52°C). While a cycle is running, pressing the Menu button will show the remaining cycle time and this can be adjusted with the up or down buttons. This time adjustment is only for remaining time of the current steam bath cycle.
Default Time Setting : The default time is programmed when the cycle is off using the Menu button. Any adjustments made to time, when the cycle is off, are stored as the new default time for both users.
RapidMist Setting: The RapidMist feature can be turned on or off when the steam cycle is in the off mode. To adjust this setting, press the Menu button until you see the Water Icon, press the Up or Down button to change this setting. Display “On” or “Off” will appear. RapidMist keeps the steam generator warm, for a faster heat up.
Fahrenheit or Celsius setting: To change this setting, while the steam cycle is off, press the Menu button until you see an “F” or “C” in the display. Use the up or down button to change the displayed letter, to correspond to your temperature choice. Press the Stop button to exit the Menu mode. Your last setting will be saved.
NOTE: The EP103314 & EP103315 controls operate and install the same way. The only difference between them is the physical shape.

Additional Features

Memory: The temperature set points for User 1, User 2, the default time, and the selection of RapidMist and other settings are retained even if there is a power failure.
Service Mode: To enter the service mode press and hold the Menu button for 5 seconds, until a blue dot lights up in the display. The control is now in the service mode. There are two features in the service mode. Pressing the up arrow displays the program version, pressing the down arrow, restores to factory default.
Error Messages: This control is programmed with a diagnostic feature to help isolate any potential problems. Errors are displayed by flashing an “Er” followed by a 2 digit number. The first digit is the device number. Zero for the control and 1-4 for the generators. The second digit is the error code for that device. Error message “Er 01”, “Er 02”, and “Er 04” indicate a problem internal to the control. If this occurs, the control should be replaced. Error messages “Er 03” means the control could not communicate with a steam generator and may be a cable connection problem. If this error occurs, check both ends of the control cable for clean, dry and secure connections. Dirty contacts can be cleaned with alcohol and a cotton swab or a toothbrush.
This can also happen if the control is not sealed and the cable connections get wet. Also make sure the generator is not in test mode. Try resetting the breaker.
Generator error codes are not covered in this document.

Limited Warranty on Brizo® Steam Bath and Steam Shower Products
Applicable to products purchased and installed in the USA and Canada

Residential Steam Bath Generators: Brizo Kitchen and Bath Company (“Brizo”) warrants to the original consumer purchaser that the parts (except for electronic parts) of its residential steam bath generator purchased from authorized Brizo sellers will be free from defects in materials and workmanship for as long as the original consumer purchaser owns the home in which the steam bath was originally installed. This lifetime limited warranty does not apply to residential steam bath generators that are used in commercial applications (as defined herein).
Residential Electronic Parts, Controls, Spa Options and Accessories:
Brizo warrants to the original consumer purchaser that the electronic parts of its steam bath generator and its controls, spa options and accessories purchased from authorized Brizo sellers will be free from defects in materials and workmanship for a period of two (2) years from the date that the product is received by the original consumer purchaser or their authorized representative (installation contractor, etc.). This two-year limited warranty does not apply to controls, spa options, electronic parts and accessories that are used in commercial applications (as defined herein).
Commercial Warranty:
For the purposes of this warranty the term “commercial application” refers to installation in any setting in which the product is not being used for personal household use, including, but not limited to, hospitality applications, day spas and short-term and long-term rentals. Brizo warrants that the parts (including electronic parts) of its steam bath generators (including steam bath generators with model numbers beginning with 8GE that are 7.5kW-15kW), equipment, controls, electronic parts, spa options and accessories purchased from authorized Brizo sellers and used in a commercial application will be free from defects in materials and workmanship for a period of one (1) year from the date that the product is received by the original purchaser or their authorized representative (installation contractor, etc.).
What We  Will Do:
Brizo will, at its option, repair or replace, free of charge, any part that proves defective in material and/or workmanship under normal installation, use and service during the applicable warranty period as stated above. Brizo may elect to refund the purchase price. Replacement parts are subject to availability and may differ from those originally supplied.
For residential applications, two (2) years following the date that the product was received by the original consumer purchaser or their authorized representative (installation contractor, etc.) and with prior approval by Brizo, Brizo will pay for labor for repair/replacement associated with warranty coverage. Thereafter, Brizo will not pay for labor associated with removal/repair/replacement of products covered by this warranty.
For commercial applications, Brizo will, with prior approval by Brizo, pay for labor associated with warranty coverage for ninety (90) days from the date that the product is received by the original purchaser or their authorized representative (installation contractor, etc.). Thereafter, Brizo will not pay for labor associated with removal/repair/replacement of products covered by this warranty.  These are the consumer’s exclusive remedies.
What Is Not Covered:
Because Brizo is unable to control the quality of Brizo products sold by unauthorized sellers, unless otherwise prohibited by law, this warranty does not cover Brizo products purchased from unauthorized sellers. This warranty does not cover damage caused by improper or negligent installation or use. Provided that Brizo is paying the cost of the labor under the terms above, this warranty does not cover repairs attempted by any person other than an authorized Brizo agent and shall be limited to the repair or replacement of defective parts by Brizo or its authorized agent.
This warranty is void if any of the following should occur:

• The use of the product for an unintended application, including a commercial application for all products except those products for which a commercial application is appropriate.
• Failure to follow instructions, including care, cleaning and usage instructions, provided in the product’s owner’s manual.
• The product’s serial number has been altered or removed.
• The product is modified in any manner which Brizo concludes, after its inspection, affects the reliability of the product.
• The product has been improperly repaired by anyone not specifically designated or authorized by Brizo.
• The product is damaged because it is not operated or installed in accordance with supplied instructions.
• The product is installed outdoors.
• The product is installed in a moist and/or humid area with unconditioned air or temperatures that exceed 104 degrees Fahrenheit.
• The product is damaged due to freezing.
• The product is damaged by acts of God.

How to Make a Warranty Claim: To obtain warranty repair or replacement, contact Brizo at: 800-355-6478 or steamprodserv@brizo.com to receive an RGA# (Return Goods Authorization number) which must be on the carton that is returned via UPS Ground or equivalent. Proof of purchase (original sales receipt showing purchase date) identifying the model and serial number and documentation of the date of receipt of the product by the original purchaser or their authorized representative (installation contractor, etc.) must accompany all warranty claims.
Limitation on Duration of Implied Warranties:
Please note that some states/provinces (including Quebec) do not allow limitations on how long an implied warranty lasts, so the below limitations may not apply to you. TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, ANY IMPLIED  WARRANTY, INCLUDING THE  IMPLIED WARRANTIES OF MERCHANTABILITY AND OF FITNESS FOR A PARTICULAR PURPOSE, IS LIMITED TO THE STATUTORY PERIOD OR THE DURATION OF THIS WARRANTY, WHICHEVER IS SHORTER.
Limitation of Special, Incidental or Consequential Damages:
Please note that some states/provinces (including Quebec) do not allow the exclusion or limitation of special, incidental or consequential damages, so the below limitations and exclusions may not apply to you. TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THIS WARRANTY DOES NOT COVER, AND BRIZO SHALL NOT BE LIABLE FOR, ANY SPECIAL, INCIDENTAL  OR CONSEQUENTIAL DAMAGES WHETHER ARISING OUT OF BREACH OF ANY EXPRESS OR IMPLIED WARRANTY,  BREACH OF CONTRACT, TORT, OR OTHERWISE.
Additional Rights:
This  warranty gives you specific legal rights, and you may also have other rights which vary from state/province to state/province. This is Brizo’s exclusive written warranty and the warranty is not transferable.

References

• brizo.com
• Contact Us : Customer Support : Brizo
• brizo.com/customer-support/product-registration

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>