TRIKDIS PC1404 Wiring GT Plus Cellular Communicator and Programming the Panel User Guide

June 17, 2024
TRIKDIS

TRIKDIS PC1404 Wiring GT Plus Cellular Communicator and Programming the

Panel

TRIKDIS-PC1404-Wiring-GT-Plus-Cellular-Communicator-and-Programming-the-
Panel-product

Product Information

Specifications

  • Product Model: PC1404
  • Product Type: Trikdis GT+ Cellular Communicator
  • Panel Compatibility: DSC PC1404

Product Usage Instructions

Wiring the Communicator to the Control Panel

Follow the provided schematics to wire the communicator to the security control panel. Ensure proper connections are made as per the diagram.

Programming the Panel

The DSC PC1404 panel does not need to be programmed separately when using the Trikdis GT+ Cellular Communicator.

LED Indication of Communicator Operation

Refer to the table below for the different light statuses of the communicator:

Indicator Light Status

Setting up the Communicator with the Protegus App

  1. 1. Download and launch the Protegus application or access the browser version at web.protegus.app.
  2. The installer must connect to Protegus using an installer account.

Performing System Check

After completing setup and installation, perform a system check by:

  1. Create an event by arming/disarming the system with the control panel’s keypad or triggering a zone alarm when armed.
  2. Ensure that the event is received by the CMS (Central Monitoring Station) and the Protegus app.

CAUTION

  • The communicator should be installed and maintained by qualified personnel.
  • Prior to installation, it is advised to read full device installation manual carefully in order to avoid mistakes that can lead to malfunction or even damage the equipment.
  • Disconnect the power supply before making any electrical connections.
  • Changes, modifications or repairs not authorized by the manufacturer shall void your rights under the warranty.

Schematics for wiring the communicator to the security control panel

Following the schematics provided below, wire the communicator to the control panel.

TRIKDIS-PC1404-Wiring-GT-Plus-Cellular-Communicator-and-Programming-the-
Panel-fig-\(1\)

DSC PC1404 panel do not need to be programmed.

LED indication of communicator operation

TRIKDIS-PC1404-Wiring-GT-Plus-Cellular-Communicator-and-Programming-the-
Panel-fig-\(2\)

Setting up the GT+ communicator with the app

Download and launch the Protegus application or use the browser version: web.protegus.app. The installer must connect to Protegus with an installer account.TRIKDIS-PC1404-Wiring-GT-Plus-Cellular-Communicator-and-Programming-
the-Panel-fig-\(3\)

Setting up the GT+ communicator with the app

After completing the setup and installation perform a system check:

  1. Create an event:
  2. by arming/disarming the system with the control panel’s keypad;
  3. by triggering a zone alarm when the security system is armed.
  4. Make sure that the event arrives to the CMS (Central Monitoring Station) and the Protegus app.TRIKDIS-PC1404-Wiring-GT-Plus-Cellular-Communicator-and-Programming-the-Panel-fig-\(4\)

FAQ

Q: Do I need to program the DSC PC1404 panel separately?

A: No, the DSC PC1404 panel does not need to be programmed when using the Trikdis GT+ Cellular Communicator.

Q: How can I check if the communicator is properly connected to the cellular network?

A: Refer to the LED indication table provided in the manual to check the status of the communicator’s connection to the cellular network.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals