TRIKDIS iO-LORA Wireless Expander Instruction Manual
- June 10, 2024
- TRIKDIS
Table of Contents
iO-LORA Wireless Expander
Product Information
The iO-LORA Wireless Expander is a device that is used to increase the number of inputs and outputs of the FLEXi SP3 control panel using two-way RF communication. It comes with an RF-LORA transceiver that provides line-of- sight wireless range up to 5000m. The device has one digital input and one output (relay) that can be remotely controlled (on/off) by various electrical devices. The bus 1-Wire is intended for connection of temperature sensor (1 pcs.) and readers of contact (iButton) keys. Up to 8 iO-LORA wireless expanders can be connected to the FLEXi SP3 control panel.
Features
- Line-of-sight wireless range up to 5000 m
- Up to 8 iO-LORA wireless expanders can be connected to the FLEXi SP3 control panel
- Bus 1-Wire is intended for connection of temperature sensor (1 pcs.) and readers of contact (iButton) keys
- 1 input, of selectable type: NC, NO
- 1 output (relay)
Specifications
| Transmission frequency | – |
|---|---|
| Modulation type | – |
| Power supply voltage | – |
| Current consumption | – |
| Report encryption | – |
| Range in open space | Up to 5000 m |
| Input | 1, of selectable type: NC, NO |
| Output | 1 (relay) |
| Temperature sensor | 1 pcs. |
| Operating environment | – |
| Dimensions | – |
| Weight | – |
Product Usage Instructions
The iO-LORA Wireless Expander should only be installed and maintained by qualified personnel. Before installation, please read the installation manual carefully to avoid any mistakes that can lead to malfunction or damage to the equipment. Always disconnect the power supply before making any electrical connections. Any changes, modifications, or repairs not authorized by the manufacturer shall render the warranty void.
To connect the temperature sensor and readers of contact (iButton) keys to the iO-LORA expander, use the bus 1-Wire. The PGM output (relay) of the expander can be remotely controlled (on/off) by various electrical devices. The iO-LORA has one digital input of selectable type: NC, NO. The iO-LORA wireless expander is connected to the FLEXi SP3 control panel via the RF-LORA transceiver. Up to 8 iO-LORA wireless expanders can be connected to the FLEXi SP3 control panel. Ensure that you adhere to your local waste sorting regulations and do not dispose of this equipment or its components with other household waste.
Safety precautions
The iO-LORA wireless expander should only be installed and maintained by
qualified personnel.
Please read this manual carefully prior to installation in order to avoid
mistakes that can lead to malfunction or even damage to the equipment.
Always disconnect the power supply before making any electrical connections.
Any changes, modifications or repairs not authorized by the manufacturer shall
render the warranty void.
Please adhere to your local waste sorting regulations and do not dispose of
this equipment or its components with other household waste.
Description
iO-LORA wireless expanders with RF-LORA transceiver increase the number of
inputs and outputs of the “FLEXi” SP3 control panel using two-way RF
communication.
Temperature sensor (1 pcs.) and readers of contact (“iButton”) keys can be
connected to the iO-LORA expander. The PGM output (relay) of the expander can
be remotely controlled (on/off) by various electrical devices. iO-LORA has one
digital input.
Features
Communication:
- Line-of-sight wireless range up to 5000 m.
- Up to 8 iO-LORA wireless expanders can be connected to the “FLEXi” SP3 control panel.
- Products from HW iO-LO_x30x_7_230418 version come with a standard antenna suitable for most applications. In cases where it is necessary to provide high-quality communication at the maximum possible distance, an antenna (AX-ANT-KIT – 433 MHz, AX-ANT01S SF –868 MHz) with a higher radio signal gain should be used.
Inputs and outputs:
- Bus “1-Wire” is intended for connection of temperature sensor (1 pcs.) and readers of contact (“iButton”) keys.
- 1 input, of selectable type: NC, NO.
- 1 output (relay).
Connection: The iO-LORA wireless expander is connected to the “FLEXi” SP3 control panel via the RF-LORA transceiver.
Specifications
| Parameter | Description |
|---|---|
| Transmission frequency | 4F modification: 433,3 – 434,7 MHz |
8F modification: 867 – 869 MHz
Modulation type| LORA
Power supply voltage| 9-26 V DC
Current consumption| Up to 50 mA (stand-by)
Up to 100 mA (short-term, while sending)
Report encryption| Yes
Range in open space| Up to 5000 m
Input| 1, selectable type: NC, NO
Output| 1, relay, 250 V AC, 4 A
Temperature sensor| 1, Maxim®/Dallas® DS18S20, DS18B20
Operating environment| Temperature from –20 °C to +50 °C, relative humidity –
up to 80% at +20 °C
Dimensions| 62 x 77 x 25 mm
Weight| 80 g
Expander elements
- Light indicators.
- Frontal case opening slot.
- Terminal for external connections.
- “SW2” button for linking the device and checking the connection.
- DIP switch „SW1“.
NOTE :
DIP switch “SW1” settings (for product HW iO-LO_x30x_7_230418 version):
- Radio frequency (“OFF” – RF1; “ON” – RF2). Intended for changing the radio channel if the current channel is heavily loaded.
- Modulation type (“OFF” – fast; “ON” – slow). The “ON” position allows you to increase the communication distance by about 2 times (depending on the environmental conditions). But if a quality connection is ensured using the “Off” position, it is recommended to use it. In the “On” position system performance decreases.
NOTE : In iO-LORA and RF-LORA devices, the positions of the “SW1” switch must match! Otherwise, the radio communication will not work!
Purpose of terminals
| Terminal | Description |
|---|---|
| +DC | Power terminal (9-26 V DC positive) |
| -DC | Power terminal (9-26 V DC negative) |
| D0 | Not used |
| D1 | Not used |
| +5V | Positive 5 V power terminal for “ 1-Wire ” devices |
| 1Wire / OUT wgd | “ 1-Wire ” data bus terminal („ OUT wgd “ – not used) |
| COM | Common negative terminal |
| IN1 | 1 input, of selectable type NO, NC (factory setting: NO) |
| NC | Relay terminal NC |
| C | Relay terminal C |
| NO | Relay terminal NO |
LED indication of operation
| Indicator | Light status | Description |
|---|---|---|
| NETWORK | Off | No RF signal |
| Green blinking | RF signal level from 0 to 10. Sufficient strength is 4. | |
| OUTPUT/KEY | Green solid | Relay output activated |
| Yellow solid | Dallas contact key activated | |
| POWER | Off | No supply voltage |
| Green blinking | Normal supply voltage level | |
| Yellow blinking | Low supply voltage level (≤11.5 V) |
Wiring schematics
Fastening
- Remove the top lid.
- Remove the PCB board.
- Fasten the base of the case in the desired place using screws.
- Reinsert the board.
- Close the top lid.
Schematic for connecting the power supply Schematic for connecting input
iO-LORA has one input. Input type can be set: NC, NO. Schematic for
connecting a temperature sensor
Temperature sensors should be connected according to the given schematic.
Maxim®/Dallas® DS18S20, DS18B20 temperature sensor (1 pcs.) can be connected
to the iO-LORA wireless expander.
If a wire longer than 0,5 meters is used to connect a temperature sensor, we
recommend using twisted pair cable (UTP4x2x0,5 or STP4x2x0,5).
The „+5V” terminal on the board is for supplying devices connected to the
“1-Wire” data bus with 5 V DC voltage.
The maximum output current is 0,2 A. The output is protected from overload. If
the maximum allowed current is exceeded, the power will automatically be
switched off. The “FLEXi” SP3 control panel automatically recognizes and links
connected temperature sensor.
Schematics for connecting CZ-Dallas reader
The CZ-Dallas iButton key reader connects to the iO-LORA using the “1 Wire”
data bus. The length of the wires connecting to the data bus can be up to 30
m. 
The output OUT
must be set to the “System State” type. Security alarm is on – the Button
reader light is red. The security alarm is off – the Button reader light is
green.
Schematics for connecting iO-LORA modules 
Note: An RF-LORA transceiver must be connected to
the “FLEXi” SP3 control panel and then up to 8 pcs. can be connected iO-LORA
wireless expanders.
It is recommended to use a twisted pair cable (UTP4x2x0.5 or STP4x2x0.5) to
connect the temperature sensor. CZ-Dallas iButton key readers and temperature
sensor must be connected to “1-Wire” bus.
Registering the iO-LORA wireless expander to the control panel “FLEXi”
SP3
- An RF-LORA transceiver must be connected to the “FLEXi” SP3 control panel.
- Turn on the power supply of the “FLEXi” SP3 control panel.
- Turn on the power supply to the iO-LORA wireless expander.
- Launch TrikdisConfig.
- Connect the “FLEXi” SP3 to a computer using a USB Mini-B cable or connect to the “FLEXi” SP3 remotely.
- Click the button Read [F4] for the program to read the parameters currently set for the “FLEXi” SP3 control panel. If a window for entering the Administrator code opens, enter the six-symbol administrator code.
- In the “Modules” list, select “iO-LORA expander”.
- In the “Serial No.” field, enter the serial number of the module iO-LORA.
- In the “Zones” tab, make settings for the expander’s input.
- In the “PGM” tab, configure the expander’s PGM output.
- Temperature sensors will be included in the “Sensors” list if a temperature sensor is connected to the iO-LORA expander.
- Once configuration is complete, click the Write [F5] button.
- Wait for the updates to finish.
- Click the “Disconnect” button and disconnect the USB cable.