TRIKDIS NX-6V2 Wiring GT Plus Cellular Communicator User Guide

June 17, 2024
TRIKDIS

TRIKDIS NX-6V2 Wiring GT Plus Cellular Communicator

TRIKDIS-NX-6V2-Wiring-GT-Plus-Cellular-Communicator-
PRODUCT

Product Information

Specifications

  • Model: NX-6V2
  • Brand: Interlogix
  • Connectivity: Cellular Communicator
  • Compatibility: Works with NX-6V2 Alarm Panel

Product Usage Instructions

Wiring Trikdis GT+ Cellular Communicator to the Panel

  1. Refer to the provided schematics for wiring guidance.
  2. Connect the communicator to the control panel following the wiring diagram.

Programming the Panel via LCD Keypad

Follow these steps to program the Interlogix NX-6V2 Alarm Panel using the LCD Keypad:

  1. Enter programming mode by pressing *89713.
  2. Access the main panel programming menu by entering 0#.
  3. Toggle Phone1 events reported menu by entering 4# and enable all toggle options with and save with .
  4. Proceed through different segments and menus as described in the manual.
  5. Exit programming mode by pressing EXIT twice.

Programming the Panel via LED Keypad

To program the panel using the LED Keypad, follow these steps:

  1. Enter programming mode by pressing *89713.
  2. Navigate through menus and segments as instructed in the user manual.
  3. Enable Contact ID reporting and configure other settings accordingly.
  4. Exit programming mode by following the provided instructions.

CAUTION

  • The communicator should be installed and maintained by qualified personnel.
  • Prior to installation, it is advised to read the full device installation manual carefully in order to avoid mistakes that can lead to malfunction or even damage to the equipment.
  • Disconnect the power supply before making any electrical connections.
  • Changes, modifications, or repairs not authorized by the manufacturer shall void your rights under the warranty.

Schematics for wiring the communicator to the security control panel

Following the schematics provided below, wire the communicator to the control panel.TRIKDIS-NX-6V2-Wiring-GT-Plus-Cellular-Communicator-
FIG-1

Programming the Interlogix NX-6V2 Alarm Panel via the LCD Keypad

Using the control panel’s keypad enter these sections and set them as described:

Enable Contact ID reporting

Using the control panel’s keypad enter these sections and set them as described:TRIKDIS-NX-6V2-Wiring-GT-Plus-Cellular-Communicator-
FIG-2

Enable Contact ID reportingTRIKDIS-NX-6V2-Wiring-GT-Plus-Cellular-
Communicator-FIG-3

LED indication of communicator operation

TRIKDIS-NX-6V2-Wiring-GT-Plus-Cellular-Communicator-
FIG-4

Setting up the GT+ communicator with the app

Download and launch the Protegus application or use the browser version: web.protegus.app. The installer must connect to Protegus with an installer account.TRIKDIS-NX-6V2-Wiring-GT-Plus-Cellular-Communicator-
FIG-5 TRIKDIS-NX-6V2-Wiring-GT-Plus-
Cellular-Communicator-FIG-5

Setting up the GT+ communicator with the app

After completing the setup and installation perform a system check:

  1. Create an event:
  2. by arming/disarming the system with the control panel’s keypad;
  3. by triggering a zone alarm when the security system is armed.
  4. Make sure that the event arrives to the CMS (Central Monitoring Station) and the Protegus app.

TRIKDIS-NX-6V2-Wiring-GT-Plus-Cellular-Communicator-
FIG-5 TRIKDIS-NX-6V2-Wiring-GT-Plus-
Cellular-Communicator-FIG-8

FAQ

How do I know if the programming was successful?

If the system displays the correct settings and exits programming mode without errors, your programming is successful.

What should I do if I encounter errors during programming?

If you encounter errors, refer to the user manual for troubleshooting steps or contact customer support for assistance.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals