AUDIBAX AWM 401 TD Professional Wireless Microphone User Manual

USER’S MANUAL AWM 401 TD / AWM 403 TD / AWM 404 TD
Professional Wireless Microphone

WELCOME TO AUDIBAX

Thank you very much for choosing Audibax. We hope you enjoy your new product.
It has been developed and designed paying attention to the smallest details, with quality control with European standards supervised by our great team of professional technicians, who work every day to offer our customers the best quality.
We make sure that every Audibax product is built to last long. All our references are made with long lasting materials and our specialists are dedicated to constantly doing quality controls to guarantee the best result.
Please read carefully this manual in order to use your Audibax product in the best way.
Do not hesitate to visit our website for further information: www.audibax.com

SAFETY INSTRUCTIONS

GENERAL INFORMATION
– It is important to read and follow the instructions carefully.
– Keep all information and instructions in a secure location.
– Always follow the instructions provided.
– Take note of all safety warnings and never remove them from the equipment.
– Use the equipment only as intended and for its intended purpose.
– Ensure that the stands and/or mounts used are sufficiently stable and compatible for fixed installations. Wall mounts should be properly installed and secured, and the equipment should be installed securely to prevent falls.
– When installing the equipment, be sure to observe the relevant safety regulations in your country.
– Do not install or operate the equipment near sources of heat, such as radiators, heat registers, or ovens, and ensure that it is always cooled sufficiently and cannot overheat.
– Do not place sources of ignition, such as burning candles, on the equipment.
– Keep ventilation slits unobstructed.
– For equipment designed for indoor use only should not be used near water, flammable materials, fluids, or gases. Special outdoor equipment should be used in accordance with the manufacturer’s instructions.
– Ensure that no dripping or splashed water can enter the equipment and do not place containers filled with liquids on the equipment.
– Prevent objects from falling into the equipment.
– Use the equipment only with recommended accessories intended by the manufacturer.
– Do not attempt to open or modify the equipment.
– Check all cables after connecting the equipment to prevent accidents or damage due to tripping hazards.
– During transport, take steps to prevent the equipment from falling and causing damage or injury.
– If the equipment is not functioning properly, fluids or objects have gotten inside, or is otherwise damaged, switch it off immediately and unplug it from the power outlet (if applicable). Only authorized, qualified personnel should repair the equipment.
– Clean the equipment with a dry cloth.
– Comply with all applicable disposal laws and separate plastic and paper/cardboard during packaging disposal.
– Keep plastic bags out of the reach of children.

FOR DEVICES DESIGNED TO BE CONNECTED TO THE MAIN POWER SUPPLY:
– ATTENTION: If your equipment has a power cord with a grounding plug, it must be connected to a wall outlet with a ground connection. Never remove the grounding plug from the power cord.
– If your equipment has been exposed to extreme temperature changes, allow it to reach room temperature before turning it on. Otherwise, moisture and condensation may damage the equipment.
– Before plugging in the equipment, make sure that the voltage and frequency of the power outlet match the specifications of the equipment. If the equipment has a voltage selector, only connect it to the power outlet if the values match. If the power cord or adapter does not fit your outlet, contact an electrician.
– Do not step on the power cord. Make sure it is not pinched at the outlet, adapter, or equipment connection.
– Keep the power cord or adapter within reach and disconnect the equipment from the power supply when not in use or when cleaning it. Always unplug the cord or adapter by pulling the plug or adapter, not the cord. Never touch the cord or adapter with wet hands.
– Avoid frequently turning the equipment on and off, as this can reduce its useful life.
– IMPORTANT: Only replace fuses with those of the same type and rating. If a fuse repeatedly blows, contact an authorized service center.
– To completely disconnect the equipment from the power mains, unplug the power cord or adapter from the outlet.
– If your device has a Volex power connector, the mating Volex connector must be unlocked before it can be removed. Be careful when laying cables, as the equipment can slide or fall if the power cord is pulled.
– Unplug the power cord or adapter before an extended period of disuse or in case of lightning strike risk.
– Only install the equipment when it is disconnected from the power source.
– To prevent damage and overheating, qualified personnel should regularly clean and service the equipment depending on ambient conditions like dust, nicotine, and fog.
If the product contains the following symbols, please, read carefully:

CAUTION
Risk of Electric Shock.
Disconnect all power sources before servicing
CAUTION: To reduce the risk of electric shock, do not remove cover (or back). There are no user serviceable parts inside. Maintenance and repairs should be exclusively carried out by qualified service personnel.
**** The warning triangle with lightning symbol indicates dangerous uninsulated voltage inside the unit, which may cause an electrical shock.
The warning triangle with exclamation mark indicates important operating and maintenance instructions.

IMPORTANT INFORMATION
CAUTION! HIGH VOLUMES IN AUDIO PRODUCTS!
This equipment is designed for professional purposes and its commercial use must comply with the applicable national rules and regulations for accident prevention.
As the manufacturer of this product, Audibax has the responsibility to inform you about the potential health risks associated with its use. One such risk is hearing damage caused by prolonged exposure to high volume.
When this product is in use, it can generate high sound-pressure levels that may cause irreversible hearing damage to performers, employees, and audience members.
To prevent this, it is important to avoid exposing yourself or others to volumes exceeding 90 dB for an extended period of time.

PACKAGE CONTENT

– 1 x AWM 401 TD / AWM 403 TD / AWM 404 TD
– 1 x User manual

RECEIVER FRONT PANEL

4-channel Reciver front panel

1. IR：frequency window
2. POWER：Power switch button
3. UP：Up button
4. IR／SET：Short press IR (IR frequency); Long press SET (setup menu)
5. DOWN：Down button

RECEIVER REAR PANEL

4-channel Receiver back panel

1. BNC antenna connector
2. MIX output Jack 6.3
3. Balanced XLR audio output
4. DC input jack

FUNCTION SETTING

Volume adjustment
4-channel Receiver: Adjust the volume by pressing the UP or DOWN button. Frequency adjustment
4-channel Receiver: Long press the IR/SET button to enter the setting mode, select FREQ by the UP or DOWN button, press the SET button again to enter the frequency modulation setting, and adjust the frequency by the UP or DOWN button.
Automatic frequency sweep
4-channel Receiver: Long press the IR/SET button to enter the setting mode, select SCAN via the UP or DOWN button, and then press the SET button to automatically sweep the frequency.
Key lock
4-channel Receiver: Long press the IR/SET button to enter the setting mode, select LOCK by the UP or DOWN button, and then press the SET button to enter the lock menu, ON means to lock, OFF means to unlock.
Infrared frequency
4-channel Receiver: Short press the IR/SET button, IR appears on the screen—indicating infrared linking is in progress

HANDHELD MICROPHONE INTRODUCTION

1. Microphone head
2. Display screen
3. Power switch
4. IR frequency window
5. Battery compartment

BODYPACK MICROPHONE INTRODUCTION

1. Microphone head interface
2. Display screen
3. Power switch
4. IR frequency window
5. Battery compartment

TRANSMITTER

1. Microphone head
2. Display screen
3. Power switch
4. IR frequency window
5. Battery compartment

IR FREQUENCY SETTING

Align the infrared pairing window of the transmitter with the infrared pairingwindow of the receiver (within 20cm), press the IR button of the receiver, thereceiver display will display “IR— —“, yes After the frequency is successful,the transmitter display will flash once and the frequency becomes the same as that of the receiver, that is, the frequency is successful.

TECHNICAL PARAMETER

Comprehensive characteristics
Carrier frequency range: 640-690Mhz
Frequency width: 2X32MHz
Modulation mode: FM FM
Frequency response: 50Hz- 15KHz
The signal-to-noise ratio (S /N):>105dB (A)
The distortion (1 KHz):<0.3%
Working temperature: -10 degrees -55 degrees
Working distance: 100 meters (ideal environment)
Receiver
Oscillation mode: PLL (digital frequency synthesizer)
Mirror suppression:≥80dB
Sensitivity: 5dBuV
Audio output level: balanced output (XLR outputjack):250mV/600 Ω
Unbalanced output: Jack 6,3mm 400mV
Working voltage: DC 12-16V
Working current:≤350mA
The hand-held transmitter
RF: the maximum power output of 30mW
Oscillation mode: PLL (digital frequency synthesizer)
Emission frequency stability: <30ppm
Dynamic range: 100dB
Frequency response: 50Hz- 15KHz
Maximum input pressure: 130dB SPL
Microphone: dynamic
Power supply: 2 (1.5V) AA type alkaline battery
Bodypack transmitter
RF: the maximum power output of 30mW
Oscillation mode: PLL (digital frequency synthesizer)
Dynamic range: 100dB
Frequency response: 50Hz-15KHz
Maximum input pressure: 130dB SPL
Microphone: Condenser microphone
Power supply: 2 (1.5V) AA type alkaline battery
Meeting microphone
RF: the maximum power output of 30mW
(Oscillation mode: PLL (digital frequency synthesizer)
Emission frequency stability: <30ppm
Dynamic range: 100dB
Frequency response: 50Hz- 15KHz
Maximum input pressure: 130dB SPL
Microphone: Condenser microphone
Power supply: 2 (1 5V) AA type alkaline battery

DISPOSAL

Packaging:

1. The packaging can be recycled using standard disposal methods and reintroduced into the reusable material cycle.
2. Please follow the laws and regulations regarding disposal and recycling of packaging in your country.

Device:

1. This device is subject to the Waste Electrical and Electronic Equipment (WEEE) Directive of the European Union. Used appliances should not be disposed of with household waste. Used device must be disposed of through an approved disposal company or a municipal disposal facility. Please comply with the applicable regulations in your country.
2. Please follow all the disposal laws and regulations in your country.
3. As a customer, you can obtain information on environmentally-friendly disposal options from the product seller or the appropriate regional authorities.

THIS DOCUMENT MAY BE SUBJECT TO MISPRINTS, ERRORS OR TECHNICAL MODIFICATIONS.

www.audibax.com

References

• Home - Audibax

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>