AUDIBAX Roma 240 Go LED Aquarium Kit User Manual

AUDIBAX Roma 240 Go LED Aquarium Kit

Product Information Roma 240 Go

The Roma 240 Go is an all-in-one battery-powered PA system that comes with a rechargeable lithium-ion battery. It features a 1 6.5 subwoofer with a 1.5 voice coil and 3 2.75 neodymium magnet high-frequency transducers with a 1 voice coil. The frequency response of the system ranges from 60 Hz to 18 kHz, and it can produce a maximum SPL of 114 dB. The system has an impedance of 4 ohms and is powered by a Class D amplifier that delivers an output power of 120W RMS. It comes with three mixer channels and two mic preamps, along with a 2-band channel EQ and reverb effects. The system has two XLR/6.3mm combo inputs, one RCA line input, and one XLR line output. It also features Bluetooth connectivity with TWS function and is housed in a polypropylene plastic enclosure that can be mounted on a 35mm pole or used as a floor monitor.

Product Usage Instructions Roma 240 Go

Before using the Roma 240 Go, please read the manual carefully and keep all safety and use instructions in mind. Here are some instructions on how to set up and use the system:

System Setup Connections and Controls

1. Signal/Clip Indicator : This indicator displays the input signal status in color. Green indicates a signal present, while red indicates signal clipping. If the signal is clipping, reduce the corresponding volume control to prevent it.
2. Volume Control : Adjust the volume of your microphone, instrument, or audio source using this control.
3. Treble Control : Adjust the high-frequency balance of your microphone or instrument.
4. Bass Control : Adjust the low-frequency balance of your microphone or instrument.
5. Effect Control : Adjust the amount of effect applied to your microphone or instrument.
6. Tone Match Switch : Move the switch to the “on” or “off” position to enable or disable the Tone Match preset.
7. Channel Input: Use the analog input to connect microphone (XLR) and instrument (TS unbalanced) cables.
8. RCA Left/Right : Connect another interface such as a cell phone, guitar, computer, and the same device, etc. input of a second Roma 240 Go to create a mono, two-loudspeaker setup. Note that Line Out is post mix.
9. TWS : With BT mode active, press TWS on both speakers to enter TWS mode. The LED will flash until a connection is made. Once connected, press TWS again to disconnect.
10. AC Input : Use this input for 100-240V AC power input.
11. Bluetooth: Press BT to activate Bluetooth mode. The LED will flash, and when Bluetooth mode is active, pressing BT will disconnect.
12. AUDIBAX-Roma-240-Go- LED-Aquarium-Kit-productPress this button to switch power ON/OFF. Though the battery will always charge while the unit is connected to AC power, Charge Only enables you to charge your battery more quickly.

That’s it! Follow these instructions, and you’ll be able to set up and use your Roma 240 Go PA system with ease.

Please read and keep all safety and use instructions. Important Safety Instructions Refer to the user manual for more information about your Roma 240 Go

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with a dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produces heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wider blade or third prong is provided for your safety. If the provided plug does not fit in your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where it exits from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualified personnel. Servicing is required when the apparatus has been damaged in any way such as power-supply cord or plug is damaged, liquid has been spilled or objects have falleninto the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped

WARNINGS/CAUTIONS

• This symbol on the product means there is uninsulated, dangerous voltage within the product enclosure that may present a risk of electrical shock.
• This symbol on the product means there are important operating and maintenance instructions in this guide.
• Contains small parts which may be a choking hazard. Not suitable for children under age 3.
• This product contains magnetic material. Consult your physician on whether this might affect your implantable medical device.

System Setup

Connections and Control

1. Signal/Clip Indicator : Displays the input signal status in color. Green: Signal present Red: Signal clipping
   Note : Reduce the corresponding volume control to prevent signal clipping.

2. Volume Control : Adjust the volume of your microphone, instrument or audio source.

3. Treble Control : Adjust the high-frequency balance of your microphone or instrument.

4. Bass Control : Adjust the low-frequency balance of your microphone or instrument.

5. Effect Control : Adjust the amount of effect applied to your microphone or instrument.

6. Tone Match Switch : Move the switch to the or position to enable the Tone Match preset.

7. Channel Input : Analog input for connecting microphone (XLR) and instrument (TS unbalanced) cables.

8. RCA Left/Right.: Connect another interface such as a cell phone, guitar, computer, and the same device, etc.

9. Line Output : Use a ¼c TRS cable to connect the line-level output to the Channel 1 or 2 input of a second Roma 240 Go to create a mono, two-loudspeaker setup.
   Note : Line Out is post mix.

10. TWS : With BT mode active, press TWS on both speakers to enter TWS mode. LED will flash until connection is made. Once connected press TWS again to disconnect.

11. AC Input : 100-240V AC power input.

12. Bluetooth: Press BT to activate bluetooth mode, LED will flash, when bluetooth mode is active, pressing BT will disconnect.

13. ON/OFF/CHARGE ONLY : Press to switch power ON/OFF. Though the battery will always charge while the unit is connected to AC power, “Charge Only” enables you to charge your battery more quickly

Specifications

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>