MOULTRIE MFA-15062 Varmint Deterrent Instructions

MOULTRIE MFA-15062 Varmint Deterrent

Product Information

Specifications

• Product : Moultrie Varmint Deterrent
• Warranty : 1-year warranty
• Required Items (must be purchased separately)
  • Self-Tapping Screw No. 6 5-8 Tap Screw – QTY : 12
  • 10′ Section of 4 Diameter PVC Pipe (Sched. 40 or Class 200)

Product Usage Instructions

Section A: Prepare your PVC for Installation

1. Lay your 10′ section of 4 Diameter PVC pipe flat on the floor.
2. Using a Tape Measure and Marker, measure 3 feet from the narrow side of the pipe and make a mark on the PVC pipe at the end of the tape measure (indicating a 3 feet long section).
3. Starting at the mark you made in the last step, mark all the way around the pipe. Be sure to keep the line straight for the best fit. (If this is difficult, you may place a zip-tie around the pipe and tighten down. Then trace along the edge of the zip-tie.)
4. Cut the pipe all the way through, along the mark from Step 3. Remember, cut the line as straight as possible for best fit. This will give you 1 of the 3 sections required. Repeat Steps 2-4 until you have three separate 3′ sections of PVC pipe.

Section B: Assemble and Install PVC Feeder Leg Bracket
Now that you have prepared the (3) pipe sections, follow these steps to assemble and install the PVC Feeder Leg Bracket

1. Remove all the parts and components from their packaging.
2. Determine if an adapter is needed for your feeder legs. You can do this by sliding the given adapters onto your feeder legs to see which has the best fit.
3. Choose one of the three configurations for installation:
   • A ONLY
   • Mounting Bracket
   • Bend in leg bracket
   • A + B
   • Mounting Bracket
   • Square Leg Adapter (leg width < 1 1/2 in)
   • A + C
   • Mounting Bracket
   • Round Leg Adapter (leg diameter < 1 3/8 in)
4. If you have difficulty screwing through the leg, drill a pilot hole with a 1/8 or smaller drill bit first.
5. Slide the PVC cap down the leg bracket so that it rests on top of the mounting bracket. If your feeder is already assembled, you will need to remove the leg assembly from the hopper to install. If you cannot remove the feeder leg bracket, install the PVC cap onto the leg bracket before mounting the leg bracket.
6. Slide one of your PVC Pipe sections up the feeder leg and firmly insert it into the PVC Cap, ensuring that the pipe is sitting flush against the inside of the cap as you secure it using (2) self-tapping screws through the mounting holes.

FAQ

• Q: How long should each PVC pipe section be?
  A: We recommend each section to be 3 feet in length.

• Q: Can I use a different size of PVC pipe for installation?
  A: The recommended size for the PVC pipe is 4 Diameter, either Sched. 40 or Class 200.

• Q: How many self-tapping screws are required for the installation?
  A: You will need a total of 12 self-tapping screws.

• Q: What if I have difficulty screwing through the feeder leg?
  A: If you have difficulty, we recommend drilling a pilot hole with a 1/8 or smaller drill bit first.

Instructions for Varmint Deterrent
Thank you for your purchase of a Moultrie Varmint Deterrent. Please read this sheet before operating the unit. If you should have any questions about this product or any other Moultrie product, please contact us using the information on the back of this sheet. Allow us to better serve you by activating your 1-year warranty online at http://www.moultriefeeders.com/warranty .

INCLUDED

Self-Tapping Screw No. 6 5-8 Tap Screw QTY: 12

MUST PURCHASE SEPARATELY

10’ Section of 4” Diameter PVC Pipe (Sched. 40 or Class 200)

 PREPARE YOUR PVC FOR INSTALLATION

Before you can begin installing the Feeder Leg Protector, you must prepare your (3) cut-to-length PVC sections. We recommend each section be 3 feet in length.

1. Lay your 10’ section of 4” Diameter PVC pipe flat on the floor.
2. Using a Tape Measure and Marker, measure 3 feet from the narrow side of the pipe and make a mark on the PVC pipe at the end of the tape measure (indicating a 3 feet long section).
3. Starting at the mark you made in the last step, mark all the way around the pipe. Be sure to keep the line straight for the best fit.(If this is difficult, you may place a zip-tie around the pipe and tighten down. Then trace along the edge of the zip-tie.)
4. Cut the pipe all the way through, along the mark from Step 3. Remember, cut the line as straight as possible for best fit. This will give you 1 of the 3 sections required. Repeat Steps 2-4 until you have three separate 3’ sections of PVC pipe.

ASSEMBLE AND INSTALL PVC FEEDER LEG BRACKET

Now that you have prepared the (3) pipe sections, remove all the parts and components from their packaging:

1. Determine if an adapter is needed for your feeder legs. You can do this by sliding the given adapters onto your feeder legs to see which has the best fit.
   Can be installed in three configurations
   A ONLY A + B A + C

2. Slide your “Mounting Bracket” (with adapter inserted – if needed) up your feeder leg as high as you can get it (up to the bend in the leg bracket – if applicable) and secure it to the feeder leg using (2) self-tapping screws.
   If you have difficulty screwing through the leg, drill a pilot hole with a 1/8” or smaller drill bit first.

3. Now slide the “PVC cap” down the leg bracket so that it rests on top of the mounting bracket (if your feeder is already assembled – you will need to remove the leg assembly from the hopper to install). If you cannot remove feeder leg bracket, install the PVC cap onto the leg bracket before mounting the leg bracket.

4. Now slide one of your PVC Pipe sections up the feeder leg and firmly insert it into the “PVC Cap”, ensuring that the pipe is sitting flush against the inside of the cap as you secure it using (2) self-tapping screws through the mounting holes.

5. Repeat Steps 2-4 until you have installed all 3 units. When all the Feeder Leg Protectors are installed on the legs and inserted into your feeder, setup is complete and your varmint deterrent system is operational!

Our Service Department will gladly answer any questions you have. www.moultriefeeders.com/support

References

• New Item Warranty | Moultrie Warranty Policy | Learn More

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>