SOUNDPEATS Mini TWS Bluetooth In-Ear Headphones User Guide

June 5, 2024
SoundPEATS

SOUNDPEATS Mini TWS Bluetooth In-Ear Headphones

SOUNDPEATS-Mini-TWS-Bluetooth-In-Ear-Headphones-PRODUCT-
IMG

First Start

SOUNDPEATS-Mini-TWS-Bluetooth-In-Ear-Headphones-FIG-
\(1\)

Open the charging case lid and take out both earbuds, then remove the insulating film and put them back.

  1. The earbuds automatically pair to each other after being taken out from the charging case. Light on main earbud flashes in red and white, the second earbud stays in white.
  2. Activate Bluetooth on the device, and choose “SOUNDPEATS Mini” on Bluetooth list to pair.

Reset

  1. Clear the pairing record from your device.
  2. Place back both earbuds into charging case and make sure they are in charging status.
  3. Press and hold both buttons for 10s until both LEDs flash in red and white twice, reset complete.

Wearing

SOUNDPEATS-Mini-TWS-Bluetooth-In-Ear-Headphones-FIG-
\(3\)

Product Diagram

SOUNDPEATS-Mini-TWS-Bluetooth-In-Ear-Headphones-FIG-
\(4\)

Touch Control

Power On| Auto: Open up the case lid and take out the earbuds

Manually: Press and hold the MFB for 1.5s

---|---
Power Off| Auto: Place back the earbuds
| Manually: Press and hold the MFB for 10s
Play / Pause| Double tap the MFB
Volume –| Single tap the le MFB
Volume +| Single tap the right MFB
Previous Track| Press and hold le MFB for 1.5s
Next Track| Press and hold right MFB for 1.5s
Answer / Hang Up Phone

Call

| Double tap the MFB
Reject Phone Call| Press and hold the MFB for 1.5s
Switch Between Two Calls| Press and hold the MFB for 2s
Manually Enter Pairing

Mode

| Press and hold the MFB for 6s while the earbuds are on
Activate Voice Assistant| Triple tap the MFB

Q&A

Q1: What does the LED on the charging case tell?SOUNDPEATS-Mini-TWS-
Bluetooth-In-Ear-Headphones-FIG- \(7\)

While charging the charging case, the LED flashes slowly.

Red Less than 20%
Yellow 20% – 69%
Green 70% – 99%
Stays in Green 100%

How to charge the case?

  1. Use a Type-C adapter to charge the case (current not over 1A). The LED flashes slowly while charging.
  2. Please charge the earbuds and case at least once per 3 months when not in use for a long time.

Q3: Why are the earbuds still connected to my phone after placing back?

  1. The charging case is out of battery. The case will not turn off the earbuds if the case battery is dead.
  2. Please make sure the earbuds sit well in the charging case, and the charging contactors on both the earbuds and charging case are clean. Please try something like microfiber cloth to clean the contactors

The battery life is not as advertised?

A single charge will not give you 20 hours playtime constantly. The earbuds work around 5 hours per charge with average use. The charging case provides another 3 recharges

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference.
  2. this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifcations not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

MANUFACTURER

Shenzhen SoundSOUL Information Technology Company Limited Room 1308-1309, Building B, Huihai Square, Chuangye Road, Longhua District, Shenzhen, China. 518109
[email protected]
www.soundpeatsaudio.com
Company:Qing UG(haftungsbeschränkt)
Address:Undinestr. 7, 12203 Berlin Germany
FCC ID : 2AFTU-DD017 MADE IN CHINA

References

Read User Manual Online (PDF format)

Loading......

Download This Manual (PDF format)

Download this manual  >>

SoundPEATS User Manuals

Related Manuals