AUDIBAX Vegas 8 Professional 15 Inch Bluetooth 300W Power Amplified Speaker User Manual

AUDIBAX Vegas 8 Professional 15 Inch Bluetooth 300W Power Amplified

Speaker

Product Information

Specifications

• Type: 2-way active speaker
• Woofer: 8 inches, 1.5VC (Vegas 8) / 10 inches, 1.5VC (Vegas 10)
• Compression driver: 25mm, 1VC
• Frequency Response: 65Hz-20KHz
• Sensitivity: 93dB
• Impedance: 8OHM
• Amplifier: Class-AB
• Mic in: XLR
• Line in: XLR & RCA & 1/8 Jack
• Line out: XLR
• Speaker out: XLR & Speakon
• EQ: Treble, Bass
• Features: LCD display, remote control, FM, Bluetooth, USB/SD, TWS
• MP3 player: Yes
• RGB lighting: Yes
• Power: 100W RMS (Vegas 8) / 120W RMS (Vegas 10)
• NW: 4.5KG (Vegas 8) / 6.0KG (Vegas 10)
• GW: 5.5KG (Vegas 8) / 7.5KG (Vegas 10)
• Package Size: 295x245x445mm (Vegas 8) / 360x295x550mm (Vegas 10)

Frequently Asked Questions

• Q: What should I do if the power LED is not illuminating?
  • A: Check the power source and ensure proper connection. If the issue persists, contact customer support for assistance.
• Q: Can I use the Vegas speakers outdoors?
  • A: While these speakers can be used outdoors, it is recommended to protect them from direct exposure to elements like rain or extreme sunlight to ensure longevity.

IMPORTANT SAFETY SYMBOLS

CAUTION

• The symbol is used to indicate that some hazardous live terminals are involved within this apparatus, even under the normal operating conditions, which may be sufficient to constitute the risk of electric shock or death.
• The symbol is used in the service documentation to indicate that specific component shall be replaced only by the component specified in that documentation for safety reasons.
• Protective grounding terminal
• Alternating current/voltage
• Hazardous live terminal

ON: Denotes the apparatus is turned on.
OFF: Denotes the apparatus is turned off.

WARNING: Describes precautions that should be observed to prevent the danger of injury or death to the operator.
CAUTION: Describes precautions that should be observed to prevent danger of the apparatus.

IMPORTANT SAFETY INSTRUCTIONS

• Read these instructions.
• Keep these instructions.
• Heed all warning.
• Follow all instructions.
• Water & Moisture

The apparatus should be protected from moisture and rain, can not used near water, for example: near bath- tub, kitchen sink or a swimming pool, etc.

Heat

• The apparatus should be located away from the heat source such as radiators, stoves or other appliances that produce heat.

Ventilation

• Do not block areas of ventilation opening. Failure to do could result in fire. Always install accordance with the manufacturer’s instructions.

Object and Liquid Entry

• Objects do not fall into and liquids are not spilled into the inside of the apparatus for safety.

Power Cord and Plug

• Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
• Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other.
• A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety.
• If the provided plug does not fit into your outlet, refer to electrician for replacement.

Power Supply

• The apparatus should be connected to the power supply only of the type as marked on the apparatus or described in the manual. Failure to do could result in damage to the product and possibly the user.
• Unplug this apparatus during lightning storms or when unused for long periods of time.

Fuse

• To prevent the risk of fire and damaging the unit, please use only of the recommended fuse type as described in the manual.
• Before replacing the fuse, make sure the unit turned off and disconnected from the AC outlet.

Electrical Connection

• Improper electrical wiring may invalidate the product war- ranty.

Cleaning

• Clean only with a dry cloth. Do not use any solvents such as benzol or alcohol.

Servicing

• Do not implement any servicing other than those means described in the manual. Refer all servicing to qualified service personnel only.
• Only use accessories/attachments or parts recommended by the manufacturer.

Warning

• Please remember the high sound pressure do not only temporarily damage your sense of hearing, but can also cause permanent damage. Be careful to select a suitable volume.

Panel Control Instruction

1. MIC INPUT(XLR)
   • This input is used to plug in microphone cable to get signal from dynamic microphone.
2. LINE INPUT (RCA & XLR & 3.5mm )
   • This input is used to connect to CD player or Cassette or other devices to get music signal.
3. Line out (XLR)
   • This input is used to output signal to another active speaker box or other amplifiers
4. Min Vol
   • This pot is used to adjust the output volume of wire microphone.
5. Line Vol
   • This pot is used to adjust the output volume of line input.
6. Master Volume
   • This pot is used to adjust the total output volume.
7. EQ
   • Treble: This pot is used to adjust the low frequency Bass: This pot is used to adjust the high frequency
8. Limit/Power indicator
   • The power led will illuminate when the system is in operation. The limit led will illuminate when the system is overloading,running your loudspeaker at clip level is not recommended and will cause the internal amplifier to fail and or the main power fuse to blow
9. TaIkover
   • Press this button down, then the talk over function will work, which means that the music signal will be decreased automatically when you use microphone
10. Speaker out
    • Plug in speaker cable with speakon connectors and connect to another passive speaker box.
11. LED switch
    • Turn on / off the led lighting on the front.
12. Power Switch
    • Turn on/off the power supply.
13. AC Socket & Fuse Holder
    • AC Socket: Plug in power cable to get AC power supply with correct Voltage Fuse Holder: Please replace fuse with correct specification
14. MP3 player
15. USB/SD connectors

  * USB is used to plug in USB Disk to play music SD is used to plug in SD card to play music
2. Mode
  * Press this button to choose the work mode like USB/SD/FM/BLUETOOTH
  * Press this button for a few seconds continually , the mp3 module will enter folder track mode
3. Pause / Play
  * Press this button to pause the working of the module and press it again to play the module .
  * When the mode is at FM status , press this button for a few seconds continually , the module will scan the FM stations automatically
4. Stop
  * Press this button to stop the working of the module.
5. Recycle
  * Press this button to recycle the music play
6. Backward.
  * Press this button to play previous music, when at FM mode , press it to choose the previous station
7. Forward
  * Press this button to play next music, when at FM mode, press it to choose the next station

Specification Chart

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>