LOCKLY GUARD ATHENA 228SL Slide Edition Door Lock Installation Guide

June 10, 2024
LOCKLY GUARD

LOCKLY GUARD logo

LOCKLY GUARD ATHENA 228SL Slide Edition Door Lock

LOCKLY-GUARD-ATHENA-228SL-Slide-Edition-Door-Lock-Installation-Guide-
product

Lockly Pro Athena Smart Lock Installation Guide

The Lockly Pro Athena Smart Lock is a commercial-grade and professional installation lockset designed for 35-65mm wooden or aluminum doors or aluminum thermal barrier doors. It comes in two editions: Slide Edition (228SL) and Swing Edition (228SW). This guide provides step-by-step instructions for installing the Lockly Pro Athena Smart Lock.

Preparation

  • Prepare door: remove existing deadbolt or use provided template to bore new holes.
  • Installation template baseline should be approximately 1 meter from the ground.

Determine Door Opening Direction

Determine the door’s opening direction and choose the lockset configuration that corresponds to it. There are four common door-opening directions: left out-swing, right out-swing, left in-swing, and right in-swing. Make sure the latch throw is correctly oriented as shown to fit your door’s opening direction.

Slide Edition: If you’re installing a Slide Edition, skip this step and proceed to Step 3.

Adjusting the Latch Throw

Athena Swing Edition with Mortise Lockset:
Follow the below steps if you’re installing Athena Swing Edition with Mortise lockset model/backset size: PGMB118 1-1/8 (28mm), PGMB138 1-3/8 (35mm), PGMB158 1-5/8 (40mm), PGMB134 1-3/4 (45mm), PGMB238 2-3/8 (60mm). The lockset ships default for right in-swing or left out-swing doors.

  1. Position and hold the lockset as shown.
  2. Move the metal barrier to loosen the latch throw.
  3. Push the latch throw inside the lockset body.
  4. Rotate the latch throw 180 degrees and allow the throw to fully extend out from the lockset after rotation.
  5. For your reference, a fully reversed latch throw is shown.

Athena Swing Edition with Multi-Point Lockset:
Follow the below steps if you’re installing Athena Swing Edition with Multi- point lockset model/backset size: PGMB138H 1-3/8 (35mm), PGMB158H 1-5/8 (40mm), PGMB134H 1-3/4 (45mm). Default setting for these lockset models is for right in-swing or left out-swing doors.

  1. Push the button up as shown.
  2. Make sure the push button is in the position as shown.
  3. Press the latch throw into the lockset, push the button to reset, the latch throw automatically extends to complete the reversal.
Adjusting the Door Handle

Before installing the key cylinder and spindle, make sure you have already adjusted your latch throw according to your door opening direction. Adjust your door handle according to your door opening direction.

Conclusion

Follow these steps carefully to install your Lockly Pro Athena Smart Lock successfully. If you have any questions or concerns, please contact our Customer Hotline: 855-562-5599.

Prepare door: remove existing deadbolt or use provided template to bore new holes.LOCKLY-GUARD-ATHENA-228SL-Slide-Edition-Door-Lock-Installation-
Guide-fig-1

There are 4 common door-opening directions, the lockset configuration as shown on each diagram below corresponds to the respective door-opening direction.

NOTE: If you’re installing a Slide Edition, skip these steps and proceed to Step 3LOCKLY-GUARD-ATHENA-228SL-Slide-Edition-Door-Lock-Installation-
Guide-fig-2

IMPORTANT
This lock is designed for 35-65mm Wooden or Aluminium Door or Aluminium Thermal Barrier Door. If your door is outside the range of the list above please contact our Customer hotline: 855-562-5599 Before installing the key cylinder and spindle, make sure you have already adjusted your Latch throw (Step 2) and door handle (Step 3) according to door opening direction.

Follow the below steps if you’re installing ATHENA SWING EDITION with Mortise lockset model/backset size: PGMB118 1-1/8” (28mm), PGMB138 1-3/8“ (35mm), PGMB158 1- 5/8“ (40mm), PGMB134 1-3/4” (45mm), PGMB238 2-3/8“ (60mm). Lockset ships default for RIGHT IN-SWING or LEFT OUT-SWING DOORS. Skip this procedure if your door orientation is as stated. See Step 1 to determine your door opening direction.
Follow the step by step direction to adjust the lockset for LEFT IN-SWING or RIGHT OUT-SWING DOORS.LOCKLY-GUARD-ATHENA-228SL-Slide-Edition-Door-Lock-
Installation-Guide-fig-3

  1. Position and hold the lockset as shown.
  2. Move the metal barrier to loosen the latch throw
  3. Push the latch throw inside the lockset body.
  4. Rotate the latch throw 180 degrees and allow the throw to fully extend out from the lockset after rotation.
  5. For your reference, a fully reversed latch throw is shown.

NOTE: If you’re installing a Slide Edition skip this step and proceed to Step 3. If you’re installing a Multi-Point Lockset for a Swing Edition, see next page to adjust the latch throw.

For ATHENA SWING EDITION with Multi-point lockset model/backset size: PGMB138H 1-3/8″ (35mm), PGMB158H 1-5/8” (40mm), PGMB134H 1-3/4” (45mm). Default setting for these lockset models is for RIGHT IN-SWING or LEFT OUT- SWING DOORS. Skip this procedure if your door orientation is as stated. See Step 1 to determine your door direction.
Follow the step by step direction to adjust the lockset for LEFT IN-SWING or RIGHT OUT-SWING DOORS.LOCKLY-GUARD-ATHENA-228SL-Slide-Edition-Door-Lock-
Installation-Guide-fig-4

CHANGING HANDLE FOR RIGHT OR LEFT SWING DOORS

The diagram below shows how to shift the door handle from right to left direction. The default setting of the handle is for right handed door. You do not need to change direction if you have a right handed door.

Change the handle direction of the Exterior AssemblyLOCKLY-GUARD-ATHENA-
228SL-Slide-Edition-Door-Lock-Installation-Guide-fig-5

Change the handle direction of the Interior AssemblyLOCKLY-GUARD-ATHENA-
228SL-Slide-Edition-Door-Lock-Installation-Guide-fig-6

IMPORTANT
Ensure the handle is correctly positioned according to desired direction (L/R)

INSTALLING THE LOCKSET

Make sure your door is prepared for installation. If you need to drill new holes, please use the supplied template for drilling holes. Before installing the Lockset S , confirm the door opening direction (Step 1) and ensure latch throw inclined part is positioned opposite to the opening direction. Insert Lockset onto door hole and secure with screws H (top and bottom) & F .LOCKLY-GUARD-ATHENA-228SL-Slide-Edition-Door-Lock-Installation-Guide-
fig-8

Adapter Positioning Screw

KM5x35mm

  • PGMB118 1-1/8″ (28mm)
  • PGMG118 1-1/8″ (30mm)
  • PGMG118H 1-1/8″ (30mm)

KM5x40mm

  • PGMB138 1-3/8″ (35mm)
  • PGMB138H 1-3/8″ (35mm)
  • PGMG138 1-3/8″ (35mm)
  • PGMG138H 1-3/8″ (35mm)

KM5x45mm

  • PGMB158 1-5/8″(40mm)
  • PGMB158H 1-5/8″(40mm)

KM5x50mm

  • PGMB134 1-3/4″(45mm)
  • PGMB134H 1-3/4″(45mm)

KM5x65mm

  • PGMB238 2-3/8″(60mm)LOCKLY-GUARD-ATHENA-228SL-Slide-Edition-Door-Lock-Installation-Guide-fig-9

Once cylinder adapter is secured, remove positioning clamp by pressing on both sides. To check if the cylinder adapter is properly installed, insert a phillips screwdriver. Turn clockwise and counter clockwise to check if the deadbolt and latch throw fully extend and retract. You may need to adjust the position of the adapter if the deadbolt and latch throw are not fully extending and retracting.

ATTACHING EXTERIOR ASSEMBLY INSTALLATION PARTS

Before installing the key cylinder, make sure your door handle have been adjusted to your door opening direction, see Step 2.

Install Key Cylinder

  1. Measure door thickness and cut off the key cylinder blade (if necessary).LOCKLY-GUARD-ATHENA-228SL-Slide-Edition-Door-Lock-Installation-Guide-fig-10
  2. Insert key cylinder O to exterior panel.
  3. Secure the cylinder with screws G (x2) on both sides.
  4. Insert M4 slotted barrel extension according to lockset dimensionLOCKLY-GUARD-ATHENA-228SL-Slide-Edition-Door-Lock-Installation-Guide-fig-11

Install Spindle A

  1. Select spindle A1/A2 according to door thickness.
  2. A1 Door Thickness 35-50mm: Spindle 62mm (x1)
  3. A2 Door Thickness 51-65mm: Spindle 77mm (x1)
  4. Install at the center hole of the exterior assembly.
  5. Insert cotter pin and bend both ends.

The illustration on the right applies for lockset : PGMB238 2 3/8″ (60mm), Athena Swing Edition.

IMPORTANT: Ensure the handle is correctly positioned according to desired direction (L/R) before bending the ends of the cotter pin.

ATTACHING INTERIOR ASSEMBLY PARTS

IMPORTANT:
The steps below will only apply for Swing Edition locksets. If you are installing Slide Edition locksets, please skip these steps and proceed to Step 6 to install the exterior and interior assemblies.

Before installing the key cylinder, make sure your door handle have been adjusted to your door opening direction, see Step 2. LOCKLY-GUARD-ATHENA-
228SL-Slide-Edition-Door-Lock-Installation-Guide-fig-17

INSTALLING THE EXTERIOR AND INTERIOR ASSEMBLY

Install the exterior assembly onto door. Ensure the spindle, lock cylinder, positioning rods and cable are inserted on the correct holes and passed through the lockset. LOCKLY-GUARD-ATHENA-228SL-Slide-Edition-Door-Lock-
Installation-Guide-fig-18

Plug the connection cable of the exterior assembly to cable of the interior assembly. Once connected, insert cable to the door frame holes. Install the interior assembly and secure with screws and C Ensure the cables are completely plush flat on the door surface. Use screw caps N to cover B screws. INSTALL DOOR FRAME AND STRIKE

Wood/Aluminum door frames (For Swing Edition locksets)LOCKLY-GUARD-
ATHENA-228SL-Slide-Edition-Door-Lock-Installation-Guide-
fig-20

Broken bridge aluminum (For Swing Edition locksets)LOCKLY-GUARD-ATHENA-
228SL-Slide-Edition-Door-Lock-Installation-Guide-fig-21

Wood/Aluminum door frames (For Slide Edition locksets)LOCKLY-GUARD-
ATHENA-228SL-Slide-Edition-Door-Lock-Installation-Guide-
fig-22

Allen wrench 2.5mm (x1)
When the strike plate is fixed on the door frame, the 2 screws should be adjusted to the inner side of the unlocking hook about 1-2mm. After the screws are locked, the surface of the exposed screws should not be lower than the surface of the strike plate. While you are inside the house, try to close and open the door. Check if the deadbolt and latchbolt fits the door frame holes and the door closes properly.

Escutcheon Screw (x2) B

  • Door Thickness 35-50mm: KM5x46mm
  • Door Thickness 51-65mm: KM5x61mm
  • Door Thickness 66-80mm: KM5x76mm

Escutcheon Screw(x1) C

  • Door Thickness 35-50mm: PM4x28mm
  • Door Thickness 51-65mm: PM4x43mm
  • Door Thickness 66-80mm: PM4x58mm

PREPARING DOOR SENSOR FOR INSTALLATION

About door sensors

Door sensors provide real-time door condition status, such as the ability to verify if the door is securely closed. It sends push notifications to your phone whenever your door opens.
Lockly Guard Athena comes with a pre-wired door sensors consisting of two parts:LOCKLY-GUARD-ATHENA-228SL-Slide-Edition-Door-Lock-Installation-Guide-
fig-23

TIP:
Lockly Guard door sensors comes in Grey (PGA715) and Matte Black (PGA716) that can be ordered through our customer hotline: +1 855-562-5599 or by email: prosales@lockly.com.

Removal of Sensor (optional)
There may be circumstances where the sensor cannot be installed because of molding/door limitations or is not aesthetically desirable. The sensor wired to the lock is removable by carefully pulling its connector from the circuit board. If removed, some features and functionality will not be available, such as real-time condition status. Make sure you install the Door Sensor indoors on a clean and dry surface. Gently wipe the surface of your door and door frame where you wish to install the Door Sensor and make sure it’s dry before installing. Keep the Door Sensor away from direct sunlight, high heat locations and large metal objects that may interfere with wireless signals.

INSTALLING DOOR SENSORS

  1. Peel the paper layer off the adhesives from the back of the wired sensor.
  2. Position the wired sensor to the edge of the door, avoiding the door strike plate. Attach and secure with the adhesives.
  3. Close the door. Before you peel the paper layer off the adhesives from the sensor magnet, align the arrow with the wired sensor. Install on to door frame.

IMPORTANT: The arrows must be aligned or as closed as possible (less than 3/4″). If needed, adjust the position of the sensor magnet using provided foam pads to ensure the sensor blinks when door opens or closes.

FINAL CHECK AND BATTERY INSTALLATION

  1. Open the battery compartment and insert 4 AA batteries. Make sure the batteries are correctly positioned.LOCKLY-GUARD-ATHENA-228SL-Slide-Edition-Door-Lock-Installation-Guide-fig-27
    Tighten the front and rear assembly fixing screws (B) and fasten with silicone plugs (N);
    Note: Please confirm that the installation is success-ful and the function is normal, and then fasten the silicone plug.

  2. Check the lock functions according to user manual after installing the batteries. Use the battery cover to secure the battery compartment and fasten with screw.

DOWNLOAD LOCKLYPRO APP

Congratulations! You have completed the Lockly Guard physical lock installation. To complete your setup, download the LocklyPro app from the iOS or Google Play app Store and follow on-screen instructions.

Scan or visit Locklypro.com/appLOCKLY-
GUARD-ATHENA-228SL-Slide-Edition-Door-Lock-Installation-Guide-
fig-29 FCC Warning:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference, and
  2. this device must accept any interference received, including interference that may cause undesired operation.

NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protec-tion against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruc-tions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. It should be installed and operated with minimum distance 20cm between the radiator & your body.

IC WARNING
This device contains licence-exempt transmitter(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

  1. This device may not cause interference.
  2. This device must accept any interference, including interference that may cause undesired operation of the device.

WARNING: This product can expose you to chemicals including Lead, which is known to the State of California to cause cancer. For more information go to www.P65Warnings.ca.gov.

INSTALLATION OVERVIEW AND PARTS LIST

LOCKLY-GUARD-ATHENA-228SL-Slide-
Edition-Door-Lock-Installation-Guide-fig-30

Parts List

Labeled As Description

A

| Spindle (x1)

A1 Door Thickness 35-50mm: Spindle 62mm (x1) A2 Door Thickness 51-65mm: Spindle 77mm (x1)


B

| Escutcheon Screw (x2)

Door Thickness 35-50mm: KM5x46mm Door Thickness 51-65mm: KM5x61mm Door Thickness 66-80mm: KM5x76mm


C

| Escutcheon Screw (x1)

Door Thickness 35-50mm: PM4x28mm Door Thickness 51-65mm: PM4x43mm Door Thickness 66-80mm: PM4x58mm

D| Cotter Pin (X1)
E| Cylinder Adapter & Clamp (x1)
F| Adapter Positioning Screw (x1)
Labeled As                           Description

G          KM4X6mm Screws (x2)
H          KM4x25mm Screws (x2)
I           Wooden Door / Aluminum Thermal Barrier Door KA4x16mm Screws (x4)
K           Aluminum Door KA3x16mm Screws(x4)
J           Strike Plate(x1)
L           RFID Card(x3)
N          Silicone Screw Caps (x2)
M          M4 (x1) M1 (x2)
O          Key Cylinder (x1) + Keys (x5)
P           Exterior Assembly
Q          Interior Assembly
R           Activation Card
S           Mortise Lockset
T           KM4X8mm Screws (x1)
U           Spacer (x1)
V          Wired Sensor
W          Sensor Magnet
X           Foam Pads
Y           Battery cover
Z           Strike Plate (x1)

Can be used for either Slide or Swing Edition (part included as per door thickness specification (A or B)LOCKLY-GUARD-ATHENA-228SL-Slide-Edition-
Door-Lock-Installation-Guide-fig-31

Included part as per Mortise Lockset specification

Parts individually packed and included according to door specifications

LOCKLY-GUARD-ATHENA-228SL-Slide-Edition-Door-Lock-Installation-Guide-
fig-32 ****

FOR COMMERCIAL USE & PROFESSIONAL INSTALLATIONLOCKLY-GUARD-ATHENA-228SL-
Slide-Edition-Door-Lock-Installation-Guide-fig-33
We’re here to help!
prosales@lockly.com
locklypro.com/support

© Copyright 2022 Lockly All rights reserved
USA Patent No. US 9,881,146 B2
USA Patent No. US 9,853,815 B2
USA Patent No. US 9,875,350 B2
USA Patent No. US 9,665,706 B2
USA Patent No. US 11,010,463 B2
AUS Patent No. 2013403169
AUS Patent No. 2014391959
AUS Patent No. 2016412123
UK Patent No. EP3059689B1
UK Patent No. EP3176722B1
Other Patents Pending
MPGD228W20220815

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals