GEORGE WILLY 42291622 Ceiling Hanging Drying Rack User Manual
- June 17, 2024
- GEORGE WILLY
Table of Contents
GEORGE WILLY 42291622 Ceiling Hanging Drying Rack
Product Specifications
- Product Name: Ceiling Hanging Drying Rack
- Material: Wood, Steel, Aluminum, Chalk
- Components: 2 x Side Bar, 12 x Dowel, 2 x Rope, 1 x Cleat, 3 x Pulley, 14 x Large Ceiling Screws, 18 x Small Dowel Screws, 1 x Allen Key
- Installation: Indoor or under shelter for wooden and steel products, suitable for outdoor use for aluminum products
Product Usage Instructions
Assembly:
- Ensure the logo is facing outwards when positioning the frame for assembly.
- Lay the Hanging Drying Rack on the floor ensuring the rope is not twisted and in the correct position before installing the dowels.
- Place the dowels evenly in the middle so they match up to the correct holes on the outside brackets. Use the Allen key to tighten the smaller screws.
- Select a suitable location ensuring enough room for easy raising and lowering of the rack.
- Screw Pulley 1 into the ceiling, ensuring it is secured to a beam.
- Install pulley 2 1085mm back from pulley 1, ensuring alignment.
- Install Pulley 3 further back from pulley 2 near the corner of the ceiling and wall, ensuring alignment.
- Install the Rope Cleat vertically below pulley 3 on the wall, ensuring alignment.
- Thread Rope A through Pulley 1, across to pulley 2, then through pulley 3.
- Thread Rope B through Pulley 2, across to pulley 3. Pull both ends of rope (A + B) until the rack is raised off the ground. Adjust for level using a builders level.
- Raise the rack to desired height (chest height recommended), tie a knot in the two ropes behind pulley 3 to prevent lowering further. Tie off rope around cleat. Cut excess rope and melt ends for a clean finish.
Frequently Asked Questions (FAQ):
- Q: Can I use liquid chalk pens on chalk products?
A: No, we recommend using traditional dry chalk only on our chalk products. Liquid chalk pens are not recommended.
CEILING HANGING DRYING RACK
Quite popular in alpine huts, a traditional system used by climbers to dry
their damp clothing overnight. It made sense to bring this idea into the home
– eliminating any worry of wet washing on the line, shrinking in the dryer or
cluttering your floor space. Suspended using a pulley system that utilities
the warm air trapped in the ceiling, The Hanging Drying Rack is a fun and
functional solution for drying your laundry.
Enjoy
George & Willy
CARE GUIDE
Where you install your product depends on its material/s.
Wooden and Steel Products: We recommend using these products inside or
under a shelter where they are protected from any exposure to rain or water.
Aluminum Products: These products are non-corrosive and suitable for use
outside.
Chalk Products: You should use traditional dry chalk. We don’t recommend
using liquid chalk pens on our products.
Transportable Outdoor Signage: If there is exposure to wind, we recommend
bringing signage inside to protect it from the extremes. We offer Sandbags to
help support your product in moderate wind conditions.
COMPONENTS
-
Please ensure that the logo is facing outwards when positioning the frame for assembly.
Please use a qualified professional to ensure safe assembly and installation of this product. Before you start assembly please lay your Hanging Drying Rack out on the floor like above, ensuring that the rope is not twisted and in the correct position before installing the dowels.
-
Once you are happy your Hanging Drying Rack is in the correct position place the dowels in the middle evenly so they match up to the correct holes on the outside brackets, using the Allen key to tighten the smaller screws.
-
Select a suitable location to install the Hanging Drying Rack. Ensure the chosen space allows enough room for the rack to be raised and lowered easily.
-
Screw Pulley 1 into the ceiling. Make sure the pulley is secured to a beam.
-
Install pulley 2 1085mm back from pulley 1 . Ensure they are perfectly aligned.
-
Install Pulley 3 further back from pulley 2 , close to the Corner of the ceiling and wall. Ensure all three pulleys are perfectly aligned.
-
Install the Rope Cleat vertically below pulley 3 on the wall. Please ensure the screws find a stud. All three pulleys and the rope cleat must be aligned.
-
Thread Rope A through Pulley 1 . Continue across to pulley 2 and then through pulley 3 .
-
Thread Rope B through Pulley 2 . Continue across and through pulley 3 . Pull both ends of rope (A+B) ) until the Hanging Drying Rack is raised off the ground. Adjust each end accordingly until the rack becomes level in the air – A builders level should be used for complete accuracy.
-
Raise the Hanging Drying Rack to the desired height attended for use (chest height recommended). Tie a knot in the two ropes just behind pulley 3 .This stops the rack from lowering any further. Tie off rope around the cleat. Cut any excess rope off and melt the ends for a clean and tidy finish.
-
We recommend tying two separate knot positions to sit under the cleat. Trim any excess rope off.
-
To keep excess rope out of reach, loop the rope up over the cleat.
Warning:
Please note that when the Hanging Drying Rack is in its up right position,
take extra care when lowering as the weight of the rack will increase when
fully loaded with garments when off the cleat.
The minimum height of the cleat needs to be installed at 170cm/67.0″ from the
ground. Allow for the droop of the loop to sit over the cleat once it is
pulled to its correct position. When the rack is in its highest position no
rope should hang lower than 140cm/55″. We recommend increasing the cleat
height if it is still in reach of young children.
DISCLAIMER
The George & Willy Hanging Drying Rack comes with Lifetime Warranty on parts.
In association with the product, George & Willy makes no warranties of any
kind, either express or implied, including but not limited to warranties of
merchantability, fitness for a particular purpose, of title, or of non-
infringement of third party rights.
George & Willy Ltd holds no liability for any harm or damage that is caused by
incorrect installation or use of a Hanging Drying Rack. The Hanging Drying
Rack must be installed by a certified professional who will be able to advise
the correct type of fixing for the ceiling that it will be installed into.
Please be sure to install the wall cleat in a position where the rope is not
accessible to small children.
CONTACT US
- @georgeandwilly
- www.pinterest.com/georgeandwilly/
- Email: sales@georgeandwilly.com
- www.georgeandwilly.com
THANK YOU
Don’t forget to tag us on Instagram @georgeandwilly For 10% off your next
purchase, use the discount code: WITHTHANKS
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>