ORTECH VT-40WMS-3CCT+W LED Vapour Tights Instruction Manual

June 17, 2024
Ortech

VT-40WMS-3CCT+W LED Vapour Tights
Instruction Manual

VT-40WMS-3CCT+W LED Vapour Tights

ORTECH VT 40WMS 3CCT W LED Vapour Tights

LED Vapour Tights
MODEL VT-40WMS-3CCT+W

WARNING
WARNING -THE INSTALLATION MUST BE CARRIED OUT BY A QUALIFIED ELECTRICIAN.
1.LED Vapour Tight  can only be installed by a qualified electrician
2. Before installation or maintenance, please disconnect the power to prevent electric shock
3. Any non-professionals are not allowed to disassemble the lamp

APPLICATION NOTICE

  • DO NOT cover the with flammable materials
  • Lamps should always be installed or replaced with care
  • Misuse of, or changes to the fixture shall nullify the guarantee
  • Before installing the lighting fixtures,  please read this instruction manual carefully
  • When a lamp is to be cleaned, make the power off and let it cool down completely. Clean the fixture with a soft cloth and a standard PH neutral detergent
  • Check the local voltage in accordance with the product requirements before using the product. Exclusively replaced by the manufacturer or his service agent or the similar qualified person in order to avoid a hazard
  • The lighting fixtures should be installed, connected and tested by a certified installer based on the local regulations
  • Re-lamping only can be done when the power is off and the lamp is completely cooled down

CAUTION
PLEASE READ INSTRUCTION BEFORE COMMENCING INSTALLATION AND RETAIN FOR FUTURE REFERENCES. Electrical products can cause death or injury, or damage to property. If in any doubt about the installation or use of this product, consult a competent electrician. Turn off the main power at the circuit breaker before installing the fixture, in order to prevent possible shock.

WIRING DIAGRAM

Note: Motion sensor models cannot be connected to a dimmer.
Motion sensor and dimming functions can be adjusted through dip switches located on sensor.ORTECH VT 40WMS 3CCT W LED Vapour Tights - WIRING
DIAGRAM

Factory Settings of Motion Sensor:

• Sensitivity: 100%
• Hold Time: 10 minutes
• Daylight Sensor: Disabled
• Stand-By Level: 10%
• Stand-By Hold Time:

MOTION SENSOR PARAMETER SETTINGS

  1. Locate the microwave sensor shown on top.
    Remove the from the mount by removing 1 screw and sliding the sensor out.

  2. On the front of the sensor, you will find switches to set the parameters for the environment.
    • Switches 1 &2 control Sensitivity.
    • Switches 3&4 control Hold Time.
    • Switches 5&6 control the Daylight threshold.
    • Switches 7&8 control Stand-by Light Level.
    • Switches 9&10 control Stand-by Time.ORTECH VT 40WMS 3CCT W LED Vapour
Tights - PARAMETER SETTINGS

  3. Switches 1 and 2 control the sensitivity. This setting controls the detection range. Follow the diagram to set the sensitivity needed for the environment.

  4. Switches 3 and 4 control the Hold Time. This setting controls how long the fixture will stay illuminated after sensing motion. Follow the diagram to set the Hold Time.

  5. Switches 5 and 6 control the Daylight threshold. This setting controls the maximum amount of daylight that will allow the fixture to illuminate. Follow the diagram to set the Daylight threshold.

  6. Switches 7 and 8 control the Stand-By Level. This setting controls the amount of light that will remain after the Hold Time has expired. Follow the diagram to set the Stand-By Level.

  7. Switches 9 and 10 control the Stand-By Time. This setting controls the amount of time the fixture will stay on at the Stand-By Level. Follow the diagram to set the Stand-By Time.

  8. Once the Parameters are set, reinstall the sensor into the fixture. Close the fixture and turn on power.

INSTALLATION GUIDE

  1. Confirm the mounting method of waterproof connector.
  2. Release the lock clips to open fixture cover.
  3. CCT& Wattage selectable.ORTECH VT 40WMS 3CCT W LED Vapour Tights - PARAMETER2
  4. Press to fasten all lock clips.
  5. Check all clips are fastened properly.

SURFACE MOUNTED

  1. Drill holes in the wall, install mounting clips to wall with screws and plastic expansion tubes.
  2. Push fixture into mounting clips for fixing.
  3. lnstalled view as bellow figure.
  4. Turn on lights after connecting to line voltage.

SUSPENDED INSTALLATION

  1. Drill hole in the wall, install the fixing base with a screw and a plastic expansion tube.
  2. Hang the mounting clip to the hook of suspension cable.
  3. Push the fixture into mounting clip for fixing.
  4. Turn on the lights after installation.

info@ortechindustries.com
www.ortechindustries.ca
13376 Comber Way
Surrey BC V3W 5V9
205 Summer lea Rd
Brampton, ON L6T 4E5
1-888-543-6473
1-888-541-6474

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals