MOUNTUP MU6007B-AU Single Monitor Mount Instruction Manual

June 17, 2024
MOUNTUP

MOUNTUP Logo INSTALLATION INSTRUCTION
CX03-01P-B_US1.0MOUNTUP MU6007B AU Single Monitor Mount

If you have any questions, please feel free to contact Customer Service via Amazon before returning.

Safety Caution

BEFORE ASSEMBLY

  • Please check and make sure all necessary accessories are included and undamaged.

  • Please read and understand this manual carefully before installation.
    WARNING

  • This product contains small items that could be a choking hazard if swallowed.
    KEEP AWAY FROM CHILDREN UNDER 3 YEARS OLD. ADULT SUPERVISION IS REQUIRED.

  • Improper installation, such as using the product for monitor over its load capacity or for any purpose not explicitly specified, may cause damage or serious injury. We would not be liable for any damage or injury caused by improper mounting or inappropriate use.
    CAUTION AND MAINTENANCE

  • Never allow children to climb, stand, hang, or play on any part of monitor or stand.

  • This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.

  • Check that the bracket is secure and safe to use at regular intervals (at least every three months).

Must Check Before Getting Started

Verify Your Monitor Specifications:

MOUNTUP MU6007B AU Single Monitor Mount - VESA Pattern

VESA Pattern (W H):
75mm
75mm (3″ x 3°)
100mm * 100mm (4” x 4°)
WARNING
DO NOT exceed the maximum weight indicated.
This mounting system is intended for use only within the maximum weights indicated. Use with products heavier than the maximum weights indicated may result in failure of the mount and its accessories, causing possible damage or injury.
Verify Your Desk Specifications:

MOUNTUP MU6007B AU Single Monitor Mount - Verify

Attention
Tension adjustment should be done only after monitor installation
WARNING:
Gas Spring Arm is under pressure and should be handled with care. Failure to follow the instructions may result in damage to the mount and/or personal injury.

Product Dimensions

MOUNTUP MU6007B AU Single Monitor Mount - Product

Supplied Parts and Hardware

MOUNTUP MU6007B AU Single Monitor Mount - PartsMOUNTUP MU6007B AU Single Monitor Mount - Parts
1

NOTE: Not all parts and hardware included will be used.
1-A Base Installation
OPTION A: Clamp Installation

Desk Thickness  .39~3.35″ (10~85mm)
A-1
Mount base (C) to pole (B) using bolts (L). Tighten them by using 5mm allen key(J). Mount Bracket (C) to base (C) using bolts (M). Tighten them by using 4mm Allen key(I).

MOUNTUP MU6007B AU Single Monitor Mount - Bracket

A-2
Attach the clamp (E) to the brace (D). Then tighten the bolts (M) with 4mm Allen key (I).

MOUNTUP MU6007B AU Single Monitor Mount - Bracket 1

A-3
Secure stand to the desktop by tightening clamp (E).
Install the decorative cover (H) to base finally.

MOUNTUP MU6007B AU Single Monitor Mount - Bracket 2

1-B Base Installation
OPTION B: Grommet Base Installation
Desk Thickness .39~2.76″ (10~70mm)
B-1
Mount base (C) to pole (B) using bolts (L). Tighten them by using 5mm Allen key(J).
Mount carriage colt (O) to pole (B) using bolts (M).

MOUNTUP MU6007B AU Single Monitor Mount - Mount

B-2
Detach the clip plate (E4) from the clamp (E).

MOUNTUP MU6007B AU Single Monitor Mount - Mount 1

B-3
If existing grommet hole comes with a plastic protector, remove it to ensure a flat surface before installing the desk mount.
Run carriage bolt (O) with base (C) through grommet hole on desktop. Secure base to the desktop by using clip plate (E4) and wingnut (N). Install the decorative cover (H) to base finally.

MOUNTUP MU6007B AU Single Monitor Mount - protector

Attach VESA Plate to Monitor

2-1 Select Correct Monitor Screw Length

MOUNTUP MU6007B AU Single Monitor Mount - Attach

Which Situation Needs Spacers?
If the screw is too long or the surface is uneven, please choose the appropriate screws and spacers for your monitor.

MOUNTUP MU6007B AU Single Monitor Mount - Attach 1

MOUNTUP MU6007B AU Single Monitor Mount - Attach 2

Do not tighten the screws excessively or tighten them by using the Electrodrill, or your monitor might be damaged.

Arm and Monitor Installation

3-1
Install the cable clip (G) and arm (A) to the pole (B). Fasten the bolts with 6mm Allen key (K).

MOUNTUP MU6007B AU Single Monitor Mount - Arm

3-2
Remove the pre-assembled security bolt (A0) from the upper arm (A).
Slide the monitor onto the head of upper arm (A), then install the security bolt (A0).
Make sure the security bolt (A0) is installed before you rotate the monitor.

MOUNTUP MU6007B AU Single Monitor Mount - Arm 1

Adjustments (If necessary)

4-1 Tilt Adjustment

  1. Loosen the tilting bolt.
  2. Adjust monitor to your desired tilt angle.
  3. Retighten the tilting bolt to fix the intended angle.

MOUNTUP MU6007B AU Single Monitor Mount - Adjustment

4-2 Tension Adjustment
The gas spring is pre-set to minimum tension (4.4 lbs). For intended functioning of the mount, you may need to adjust the tension of Arm in accordance with your monitor weight by 6mm Allen key (K).

MOUNTUP MU6007B AU Single Monitor Mount - Tension

Note:
Be sure to keep the arm in a horizontal position during adjustment.
Or else it would be difficult to adjust the mount or damage the mount.

Situation 1: Arm falls down Upper Arm with monitor falls down and fails to stay where intended.
Solution:
Turn the inside screw counterclockwise (“+”direction) to increase gas spring tension until the arm can stay as intended.

MOUNTUP MU6007B AU Single Monitor Mount - Tension 2

Situation 2: Arm rises up or can’t press down Upper Arm with monitor rises up and fails to stay where intended.
Solution:
Turn the inside screw clockwise (“-”direction) to decrease gas spring tension until the arm can stay as intended.

Cable Management

MOUNTUP MU6007B AU Single Monitor Mount - Cable

Lower Arm
Remove the bottom plastic cover from lower arm as shown in the diagram. Run cables through the cable cover, then insert and slide the cover down for reattachment.
Adjust monitor position and rotation.

MOUNTUP MU6007B AU Single Monitor Mount - Cable 1

Note: To ensure stability, the tightness of the rotating axis has been preset, so it would be kind of difficult to rotate the VESA plate.
Suggestion: Please attach the monitor first, then hold the sides of it with both hands, and rotate vigorously. If that doesn’t work out, please do not hesitate to ask for our help.

MOUNTUP Logo

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals