Aerpro APH005 0.5W UHF CB Handheld Radio Twin Pack User Guide

Aerpro APH005 0.5W UHF CB Handheld Radio Twin Pack

Specifications

• Frequency: 476.425 – 477.4125 Mhz
• Channel number: 80 channels
• Sub-code: CTCSS 38 Codes
• Transmission Power: 0.5 Watt
• Battery Type: 3 x AAA Batteries Each (Not Included)

Product Information

The Aerpro APH005 0.5 Watt UHF CB Radio Kit is a reliable communication device designed for various applications. It comes with 80 channels, CTCSS sub-codes, and operates at a transmission power of 0.5 Watt. The radio requires three AAA batteries for operation (batteries not included).

Product Usage Instructions

Safety Information and Warnings
Before using the UHF radio, familiarize yourself with the safety information and warnings provided in the manual. Ensure compliance with local regulations and guidelines for radio operation.

Safety and General Use While in a Vehicle
Check and adhere to State and Federal laws regarding the use of two-way radios in your driving area. Avoid placing the radio near airbags as it may pose a risk of injury if the airbag deploys.

Potentially Explosive Atmospheres
To prevent interference with blasting operations, turn off the radio near blasting caps or in designated blasting areas. Follow all safety signs and instructions to ensure safe operation.

Exposure to Radio Frequency Energy
Adhere to radio operating procedures to maintain optimal performance and ensure human exposure to radio frequency electromagnetic energy is within set guidelines. Avoid unauthorized modifications that could damage the radio.

Electromagnetic Interference/Compatibility
To prevent electromagnetic interference, turn off the radio in locations where posted notices advise doing so, such as healthcare facilities. Follow guidelines to maintain compatibility with other electronic devices.

Aircraft
Comply with airline regulations and crew instructions regarding the use of radios on aircraft. Turn off the radio when instructed to do so to ensure safe operation during flight.

FAQ

• What type of batteries does the radio require?
  The radio operates on three AAA batteries, which are not included in the package.

• How many channels does the radio have?
  The radio has 80 channels for versatile communication options.

INTRODUCTION

WELCOME
Thank you for purchasing the Aerpro APH005 0.5 Watt UHF CB Radio Kit. Please ensure that you have read the product manual and instructions in full, prior to installation and use. Failure to do so may result in product failure/damage or incorrect operation and therefore impact the product performance.

FEATURES

• VOX voice activated transmission
• 0.5 Watt transmission power
• 80 Narrow-band channels
• Squelch control (automatic)
• CTCSS (38 Codes)
• Duplex range extender
• Channel scan function
• LED torch light
• 10 call ring tones
• Roger beep
• Button beep
• Backlight display

BOX CONTENTS

• UHF CB Radio (x2)
• Belt Clip (x2)

TECHNICAL SPECIFICATIONS

• Frequency 476.425 – 477.4125 Mhz
• Channel number 80 channels
• Sub-code CTCSS 38 Codes
• Transmission Power 0.5 Watt
• Battery Type 3 x AAA Batteries Each (Not Included)

SAFETY INFORMATION AND WARNINGS

INFORMATION ON SAFE OPERATION
Please read this information before installing or using your UHF radio.
The operation of your UHF radio in Australia is subject to conditions in the follow-ing Licence: In Australia the ACMA Radio communications (Citizen Band Radio Stations) and in New Zealand by MED the General User Radio Licence for Citizen Band Radio.

SAFETY AND GENERAL USE WHILST IN A VEHICLE
Check the State and Federal laws and regulations regarding the use of two way radios in the area where you drive, and always obey them.

FOR VEHICLES FITTED WITH AIRBAGS
When using the radio in a vehicle, do not place your radio in the area over an air-bag, or in the airbag deployment area. Airbags inflate with great force, if a radio is placed in the airbag deployment area and the air bag inflates, it may be propelled with great force and cause serious injury to the occupants of the vehicle.

POTENTIALLY EXPLOSIVE ATMOSPHERES
Turn your radio OFF when in any area with a potentially explosive atmosphere. Sparks in such areas could cause an explosion or fire resulting in injury or even death. NOTE: Areas with potentially explosive atmospheres are often, but not always clearly marked. They include fueling areas such as below deck on boats; fuel or chemical transfer or storage facilities; areas where the air contains chemi-cals or particles, such as grain, dust, or metal powders; and any other area where you would normally be advised to turn of your vehicle engine.

BLASTING CAPS AND AREAS
To avoid possible interference with blasting operations; turn your radio OFF near electrical blasting caps, or in a “blasting area”, or in areas posted: “Turn off the two way radio.” Obey all signs and instructions.

EXPOSURE TO RADIO FREQUENCY ENERGY
Your two-way radio complies with Australian Communications Authority Radio Communications (Electromagnetic Radiation-Human Exposure) Standard, 2003. To assure optimal radio performance and make sure human exposure to radio frequency electromagnetic energy is within the guidelines set out in the above standards always adhere to the following radio operating procedures.

RADIO OPERATION AND EME EXPOSURE
Unauthorised antennas, modifications, or attachments could damage the radio and violate compliance. DO NOT hold the antenna when the radio is “IN USE.” Holding the antenna reduces the effective range. DO NOT use the radio if the antenna is damaged. If a damaged antenna makes contact with a persons skin, a minor burn may result.

ELECTROMAGNETIC INTERFERENCE/COMPATIBILITY
Nearly every electronic device is susceptible to electromagnetic interference (EMI). To avoid the possibility of electromagnetic interference and/or compatibility conflicts, turn off the radio in any location where posted notices instruct you to do so such as health care facilities.

AIRCRAFT
When instructed to do so, turn off your radio when on-board an aircraft. Any use of a radio must be in accordance with applicable regulations per airline crew instructions.

MEDICAL DEVICES – PACEMAKERS
The Advanced Medical Technology Association recommends a minimum separation of 15cm be maintained between a radio and pacemaker. These recommendations are consistent with the independent research by, and recommendations of, the U.S. Food and Drug Administration. People with pacemakers should:

• ALWAYS keep the radio more than 15cm away from the pacemaker when the radio is powered on.
• NOT carry the radio in the breast pocket (handheld models).
• Use the ear opposite the pacemaker to minimise the potential for interference.
• Turn the radio OFF immediately there is any reason to suspect that interference is taking place.

MEDICAL DEVICES – HEARING AIDS
Some radios may interfere with some hearing aids. In the event of such interference, you may want to consult your hearing aid manufacturer to discuss alternatives.

MEDICAL DEVICES – OTHER
If you use any other personal medical device, consult the manufacturer of your device to determine if it is adequately shielded from RF energy. You physician may be able to assist you in obtaining this information.

GENERAL WARNINGS
Some radios may interfere with some hearing aids. In the event of such interference, you may want to consult your hearing aid manufacturer to discuss alternatives.

BATTERIES
All batteries can cause property damage and/or bodily injury such as burns if conductive material such as jewelery, keys, or beaded chains touch exposed terminals. Do not replace or charge batteries in a potentially explosive atmosphere.

RADIO CONTROLS

RADIO LAYOUT

LCD DISPLAY

LCD DISPLAY

INSTALLING THE BATTERIES & BELT CLIP

Battery pack:
Each handheld CB radio requires 3 AAA batteries (not included). On the back of the handheld CB radio, lift up the release tab on the battery cover and remove. Place the 3 AAA batteries in the correct position as marked on the inside of the handheld CB radio. Replace the battery cover and you are ready to go.

Belt clip:
Place the belt clip to the corresponding grooves on the back of the transceiver, and then pull downwards. Press and hold release tab, then pull upwards to release.

RADIO OPERATIONS

POWER ON/OFF
To turn the APH005 on or off, press and hold the Power on/off button for 3 seconds until you hear a beep sound.

VOLUME CONTROL
To increase the volume, press the Up ▲ button. And press the Down ▼ button to decrease the volume.

BATTERY VOLTAGE DISPLAY
The APH005 can detect a low battery level when the battery voltage goes low. When the battery voltage is low, the battery icon will flash on screen and a beep sound will be heard to indicate that the batteries will need to be replaced.

RECEIVING / TRANSMITTING

• The devices are in “Standby” mode when it is turned ON and not transmitting. When a signal is received on the current channel, the LCD will display a receiving icon in “reception” mode.
• When you press the PTT (push to talk) button, the devices switches to “Transmission” mode. Hold the device in a vertical position with the Mic (microphone) 3-5cm away from your mouth. While holding the PTT button, speak into the microphone in a normal tone of voice. Release the PTT button when you have finished transmitting.
• For others to receive your transmission, they must be on the same channel with you.
  NOTE: The talking range will depend on your surroundings and environment. It will be affected by obstructions such as hills or buildings. Don’t try to use two devices which are less than 1.5m (5 feet) apart. Otherwise, you may experience interference.

CHANNEL OPERATIONS

CHANGING CHANNELS

• Press the MENU button one time, the channel number will flash on the display. Press the Up▲/Down▼ button to change the channel.
• Press the PTT button to confirm and return to stand-by mode.
  NOTE: If no button is pressed within 9 seconds during setting, the device will return to stand-by mode.

CTCSS (Continuous Tone Coded Squelch System)

• Press the MENU button 2 times, the current CTCSS code will flash on the display. Press the Up▲/Down▼ button to change the 38 available codes.
• Press the PTT button to confirm and return to stand-by mode.
• When operating on the 476.4250MHz to 477.4125 MHz License free radio frequency band, the APH01 has 80 available radio channels. If there are many device users near you, there is a chance that some of the users are operating on the same radio channel.
• When using CTCSS, a low frequency tone (between 67-250Hz) will be transmitted along with the voice signal. CTCSS codes are 01 -> 38. Due to filtering, these sub-channels will generally not be audible so they will not disturb the communication.

VOX (Hands free function)

• Press the MENU button 3 times, the current VOX setting will flash on the display and the VOX icon will display.
• Press Up▲ button to set the VOX sensitivity level between 1 and 3 level (level 3 is the high sensitive level).
• Press Down▼ button until “OF” appears on the display to turn VOX OFF.
• Press the PTT button to confirm and return to stand-by mode.
• In VOX mode, the radio will transmit a signal when it is activated by your voice or other sound around you.
• VOX Operation is not recommended if you plan to use your device in a noisy or windy environment.
  NOTE: VOX mode will be overridden when you press the PTT button.

SETTING THE CALL TONES

• The device has 10 call tones.
• Press the MENU button 4 times, “CA” is displayed and on the current call tone. Press the Up▲/Down▼ button to change another call tones.
• Press the PTT button to confirm and return to stand-by mode.

KEY TONE ON/OFF

• To turn the key tone on/off. Press the MENU button 5 times, “TO” will be displayed.
• Press the Up▲/Down▼ button disable the key tone ON/OFF.
• Press The PTT button to confirm your selection and return to the stand-by mode.

ROGER BEEP ON/OFF
After the PTT button us released, the device will send out a roger beep to confirm you have stopped talking.

1. Press the MENU button 6 times, “RO” will be displayed.
2. Press the Up▲/Down▼ button disable the roger beep ON/OFF.
3. Press The PTT button to confirm your selection and return to the stand-by mode.

REPEATER ON/OFF

• Press the MENU button 7 times, “RP” will be displayed.
• Press the UP▲/Down▼button disable the Repeater ON/OFF.
• Press the PTT button to confirm your selection and return to the stand-by mode. This turns ON all 16 Repeater channels 01 -> 08 & 41 -> 48

SCANNING FOR AN ACTIVE RADIO CHANNEL
Press and hold the Up▲ button for 2 seconds: The “SCAN” function indicator will appear on the display and the channel will scan continuously from 1 to 80. Once an active channel is found, the scanning will stop and you can listen to the transmission. When the transmission is on the found channel stop, the scanning will resume automatically.
NOTE: If you press PTT button while listening to a found channel, the device will go back to stand-by mode on the found channel.

SENDING A CALL TONE
Press the call button quickly, the call tone will be transmitted on the setting channel.

MONITOR

• Press and hold the Down▼ button for about 2 seconds to active monitor. Release the Down▼ button to return to stand by mode.
• This temporarily turns OFF the automatic squelch

BACKLIT DISPLAY
Press any button except for the MENU button to activate the back light of the LCD display. The back light will light on about 5 seconds.

BATTERY SAVING FUNCTION
When the device has not been used for 6 seconds, the economy mode is automatically activated. This does not affect the reception of transmission and the stand by mode is automatically re-activated as soon as a signal is detected.

BUILT-IN FLASH LIGHT
Your device has a built-in flash light that can be used in sending light signals or for your lighting needs.

LOCK & UNLOCK THE DEVICE
Press and hold MENU button for 3 seconds to lock & unlock the device.

RESETTING THE DEVICE
Turn radio OFF first and then press & hold on the Power button and PTT button together for 2 seconds, the device will be power on and reset back to Channel NO.1.

FUNCTION

CTCSS
WHAT IS CTCSS?

• CTCSS (Continuous Tone-Coded Squelch System) modifies the transmission signal to allow privacy while sharing the same channel, without disturbing each other. This is an important feature on a radio when there are many radio users in the same area.
• CTCSS continuously superimposes any one of about 50 low-pitch audio tones on the transmitted signal, ranging from 67 to 254 Hz.

BUTTON BEEP
WHAT IS BUTTON BEEP?
When buttons are pressed on the radio (exc. PTT Button), the radio emits a beep tone to indicate the button has been pressed. The radio has button beep default on.

FUNCTION- Using The UHF Radio

TRANSMIT AND RECEIVE PROCEDURE

• Your UHF radio contains a transmitter and receiver. To control your exposure and ensure compliance with the general population/uncontrolled environment exposure limits, always adhere to the following procedure:
  • Transmit no more than 50% of the time.
  • To receive calls, release the “(PTT) BUTTON” on the microphone handpiece.
  • To transmit (talk), press the “(PTT) BUTTON” on the microphone handpiece.
• When powered on and not transmitting, the radio is always in receive mode. When a signal is received the LCD will display the RX indicator, and then you can hear if the other party is calling. NOTE: You may not receive the call if you set a high “squelch off” level of the transceiver.
• If current channel has been programmed with signaling, you can only hear the call from the same signaling, other calls can not be heard. For others to receive your transmission, they must be on the same channel as you and if CTCSS or DCS is enabled, the same sub channel must also be selected.
  NOTE: Transmitting 50% of the time, or less, is important because the radio generates measurable RF energy exposure only when transmitting (in terms of measuring standards compliance).
  NOTE: Do not transmit between two radios that are less than 1.5m apart, otherwise you may experience interference.
  NOTE: The UHF radio is simplex “one way at a time”. While you are speaking, you can not receive a transmission.
  NOTE: The UHF radio is an open licence band. Always identify yourself when transmitting.

TRANSMITTING RANGE
The transmitting range will depend on the antenna, terrain, surroundings and environment, it will be affected by obstructions such as hills, buildings and foliage. The use of duplex mode will extend the transmission range in areas where a repeater station is present.

FUNCTION- Duplex Mode Via Repeaters

DUPLEX REPEATER MODE

• This feature allows the use of local repeater stations that are designed to automatically re-transmit your broadcast over large areas, thus increasing the range of the UHF radio. Repeater stations are privately operated radio systems and are installed throughout Australia each repeater station operates on preset channels. Check the area you plan on traveling to for any repeaters and their channel.
• The duplex mode on the radio helps increase the range of the radio using repeater stations. In duplex mode, the fixed position station forwards the signal it receives from repeater input stations (31-38)/(71-78) to the corresponding output stations (1-8)/(41-48). Any transmissions sent on non-duplex channels are sent in simplex mode, or directly between radios without the use of a repeater.

SELECTING REPEATER

• To access the repeat feature, press the “(MENU) button” 7 times, “RP” will display on the screen. Press the “UP button” or “DOWN button” to select an option “on or off”.
• Once the desired option has been selected, press the “(PTT) button”and this will save the selected option and the radio will return to the default screen.

DUPLEX / REPEATER INFORMATION

DUPLEX RECEIVE/TRANSMIT CHANNEL GUIDE
The following table displays the receive and transmit channels when using repeater stations:

VISUAL REPRESENTATION OF DUPLEX

UHF CB CHANNEL GUIDELINES

RADIO COMMUNICATIONS (CITIZEN BAND RADIO STATIONS) CLASS Licence 2002

• NOTE: The operation of your UHF radio in Australia and New Zealand is subject to conditions in the following Licences: In Australia, the ACMA Radio Communications (Citizen Band Radio Stations) and in New Zealand by MED the General User Radio Licence for Citizen Band Radio.
• No Licence is required to own or operate this radio in Australia or New Zealand. The Radio Communications (Citizen Band Radio Stations) Class Licence 2002 contains the technical parameters, operating requirements, conditions of Licence and relevant standards for Citizen Band (CB) radios. CB radios must comply with the class Licence for their use to be authorised under the class Licence. Licences for Repeater
• Channels 44 & 45 will not be Licenced for an additional 6 to 12 months to allow extra time for owners of Channel 5 Emergency repeaters to upgrade equipment to meet new standards.
• Channels 1 to 8 and 41 to 48 – Repeater Channels. Enable duplex mode on your radio to use any available repeaters.
• Channels 5 & 35 – Emergency use only. Monitored by volunteers, no general conversations are to take place on these channels.
• Channels 22 & 23 – Data transmissions only (excluding packet).
• Channels 31 to 38 and 71 to 78 – Repeater inputs. Do not use these channels for simplex transmissions as you will interfere with conversations on channels 1 to 8 and 41 to 48.
• The Australian Government legislated that channels 5 & 35 on the UHF CB Band are reserved for emergency use only.
• If you do find you are interfering with another persons conversation, just select another channel.

IMPORTANT CHANNEL INFORMATION
A list of currently authorised channels can be obtained from the ACMA website in Australia and the MED website in New Zealand.
Please note the following channel guidelines:

• Channels 01-08 (and 31-38), and Channels 41-48 (and 71-78) are repeater channels.
• Channels 05 and 35 are emergency channels, do not use these unless it is an emergency.
• Channel 11 is a calling channel.
• Channels 22 and 23 are for telemetry and telecommand applications (Data Only).
• Channel 40 – road channel (Australia).
• Channels 61, 62 and 63 are reserved for future use and TX is inhibited on these channels.

UHF CB CHANNELS AND FREQUENCIES

UHF CHANNEL FREQUENCY TABLE

CTCSS TONE TABLE (Codes 01 - > 38)

TROUBLE SHOOTING GUIDE

• No power

  • The batteries may be exhausted. Replace with new batteries
  • The batteries may not be installed with correct polarity. Remove and install the batteries correctly
  • The power switch is broken. (Contact your local dealer for repairs)
  • Battery contacts are broken. (Contact your local dealer for repairs)

• Cannot talk to or hear other members in your group

  • Different frequency or channel used, try another.
  • Different CTCSS settings. Please reset settings.
  • Out of communication range.

• Cannot power on or frequent power-off
  Check the batteries are NOT flat

• Intermittent receiving with loud noise.
  Out of communication range or obstructed by tall buildings or in basement and so on.

• Receive voice from the other party but can not transmit
  Check [PTT] key. (Contact your local dealer for repairs)

TECHNICAL ASSISTANCE

• If you need assistance setting up or using your AERPRO product now or in the future, call Aerpro Support. Australia
  • TEL: 03 – 8587 8898
  • FAX: 03 – 8587 8866
  • Mon-Fri 9am – 5pm AEST
  • Email: [email protected]
  • Please retain this user guide for future reference.
• If you would like to download a digital copy of this manual, or other Aerpro manuals/software, please visit the Aerpro.com website and click on ‘Firmware & Manuals” or search for the product model number for more information, accessories and products.
• This manual is considered correct at time of printing but is subject to change.
• For latest manuals and updates refer to the website.
• Copyright © 2023 by TDJ Australia
• All rights reserved. No part of this publication may be reproduced, distributed, or transmitted in any form or by any means, including photocopying, recording, copying or other electronic or mechanical methods, without the prior written permission of the author.
• www.aerpro.com

References

• Home | Aerpro
• Home | Aerpro

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>