Fluval 12345 Flex Marine Aquarium User Manual
- June 17, 2024
- Untitled
Table of Contents
Untitled 12345 Flex Marine Aquarium
Specifications:
- BATCH NO: 12345
- CABINET ASSEMBLY INSTRUCTIONS Version 4
- Tools Required:
- Ax8
- Bx2
- Cx10
- Dx8
- Ex2
- Fx2
- Gx8
- Hx5
- Jx1
- Kx2
- Lx6
- Mx8
- Nx6
- Ox2
- Px2
- Included:
- Qx2
- Rx2
- Sx8
- Tx2
- Ux2
- Vx2
- Glue – Leim Colle – Pegamento
Product Usage Instructions:
Lay Parts on a Flat Clean Surface:
We recommend that you build your cabinet in its final location which must
be solid, flat, and level. The aquarium can then be assembled on top.
Apply Glue and Insert Dowels:
Apply a drop of glue into the dowel holes on panels (i), (iii), and (iv)
before inserting dowels (G).
Reattaching Hinge Plate:
If the hinge plate becomes detached from the hinge, you can reattach it as
shown.
- Click On: Soft Close
- Slide On: Standard Close
- Zusammenschieben: Standard Scharnier
Assembly:
Assemble the cabinet according to the provided diagrams and instructions.
FAQ
Q: Can I build the cabinet on any surface?
A: We recommend building the cabinet on a solid, flat, and level surface
for stability.
Q: How should I attach the hinge plate if it becomes detached?
A: You can reattach the hinge plate by following the instructions provided
in the manual.
Q: What type of hinge does the cabinet use?
A: The cabinet can be equipped with either a soft-close or standard-close
hinge.
CABINET ASSEMBLY INSTRUCTIONS
CUSTOMER SERVICE
CANADA :
Customer Services: Roif C. Hagen Inc., 20500, Trans Canada Hwy, Baie d’Uffe QC
H9X 0A2 8 1 800 56HAGEN (1 800 554-2436)
DEUTSCHLAND:
Kundendiens: HAGEN Deutschland GmbH & Co. KG, Lehmweg 99-105, D-25488 Holm 3
+49 (0) 4103 980 2000
UK:
Customer Services: Roil C. Hagen (UK) Lid. California Drive. Whitwood Ind Est.
Castleford, West Yorkshire, WF10 5QH. * 01977 556822
USA:
For authorized guarantee repair service return with dated receipt and $4.00
for postage and handling to: Consumer Repairs, Rolf C, Hagen (USA) Corp, 305
Forbes Bivd, Mansfield, MA 02048 2
1-800-724-2436
Important – Please read these instructions fully before startina assembly.
FITTINGS
PREPARATION
LAY PARTS ON A FLAT CLEAN SURFACE – We recommend that you build your cabinet in its final location which must be solid, flat and level. The aquarium can then be assembled on top.
PREPARATION
Attention! Fit the soft close hinge at the top and the standard hinge at the bottom. Knock in hinges with a mallet then tighten the screws.
If the hinge plate becomes detached from the hinge you can reattach it as shown.
ASSEMBLY
Apply a VERY SMALL drop of glue into the end dowel holes on panels (ii), (iii) & (iv) before assembling.
Apply a VERY SMALL drop of glue into the dowel holes on panels (ii), (iii) & (11) before assembling.
Attention! Washers (F) must be used to ensure even spacing between the false drawer and the door.
This product was manufactured for Rolf C. Hagen by Aquapac Ltd.
Attention! Make sure glide ‘V’ is positioned the correct way around. The 4 x screw holes must align with the holes drilled on the panel.
STOP! After assembly, it is strongly recommended that you seal all inside joints of the top panel trim to safeguard against water spills. Apply a very fine bead of transparent silicone and smooth out / wipe away any excess with a wet finger to create a smooth finish.
Attention! Ensure fittings ‘H’ are correctly fitted so the deep side of the hood rests on the tank
3D Hinge Adjustment – How to align the doors
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>