QualGear PRB-717-Blk Ceiling Mount Projector Accessory Instruction Manual

QualGear PRB-717-Blk Ceiling Mount Projector Accessory

Specifications

• Model: PRB-717-BLK
• Weight: 13.6kg (30lbs)
• Warranty: 2 Year Limited Warranty (Version: December 2023)

Installation Precautions

• Please read the entire installation manual before starting installation and assembly.
• Ensure that all parts are included before starting installation.
• Do not begin installation until you have read and understood all the instructions and warnings in the installation manual.
• This product should only be installed by someone with good mechanical aptitude, experience with basic building construction, and a full understanding of the instructions.
• Improper installation may cause damage or serious injury, and QualGear is not liable for improper use or installation.
• Tighten screws firmly, but do not over tighten to avoid damaging the items.
• All QualGear products are intended for indoor use only. Outdoor use voids the limited warranty.
• All QualGear products are designed and tested for residential use only. Commercial use voids the limited warranty.
• If mounting to wooden studs, make sure to anchor mounting screws into the center of the studs. Use of an edge-to-edge stud finder is highly recommended.
• Never exceed the maximum rated weight specified in this manual.
• Ensure that the supporting surface can safely support the combined load of the equipment and all attached hardware and components.
• Use all bolts and screws at the designated points in the installation instructions to prevent property damage and/or personal injury.
• Always use an assistant or mechanical lifting equipment to safely lift and position the equipment.
• Do not install near air conditioner vents or in areas with excessive dust or smoke.
• Take care of electrical cables, water, or gas pipes in the wall when drilling holes.
• This product is designed to be installed on wooden stud, wooden beam, solid concrete, or other specified wall construction types.

Installation

WARNING

• Do not begin to install your QualGear product until you have read and understood all the instructions and warnings contained in this installation manual.
  US customers with questions regarding instructions, please contact QualGear customer support via email at support@qualgear.com. For all international customers, please contact your local distributor.

• This product should only be installed by someone of good mechanical aptitude, has experience with basic building construction, and fully understands these instructions.

• This product was designed to be installed and utilized only as specified in this manual. Improper installation of this product may cause damage or serious injury. QualGear is not liable for the improper use or installation of its products.

• Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components.
  Always use an assistant or mechanical lifting equipment to safely lift and position the equipment.

• Tighten screws firmly, but do not over tighten. Over tightening can damage the items, greatly reducing their holding power.

• All QualGear products are intended for indoor use only and any outdoor use voids the limited warranty.

• All QualGear products are designed and tested for residential use only and any commercial use voids the limited warranty. For warranty information, please visit http://www.qualgear.com/warranty.php.

• If mounting to wooden studs, make sure that mounting screws are anchored into the center of the studs. Use of an edge-to-edge stud finder is highly recommended.

• Never exceed the maximum rated weight specified in this manual.

• All bolts and screws must be used at the designated points in the installation instructions to prevent property damage and/or personal injury.

• DO NOT install near air conditioner vents or where there is excessive dust or smoke.

• When drilling holes in the wall, it is very important to take care of electrical cables, water, or gas pipes in the wall.

This product was designed to be installed on the following wall construction only:

WALL CONSTRUCTION

• Wooden Stud
• Wooden Beam
• Solid Concrete
• Other

HARDWARE REQUIRED

• Included
• Included
• Included
• Contact Qualified Professional

Parts Checklist

IMPORTANT : Before starting installation, please check that all parts shown in this checklist are included. If any parts are missing or damaged, contact your local distributor or support@qualgear.com for replacement parts and do not start assembly and installation until you receive all the parts.

1A Installing the Ceiling Mount (Wood Joist Surfaces)

Depending on the direction of the studs, choose the mounting holes accordingly.

WARNING

• Installers must verify that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.
• Make sure that mounting screws are anchored into the center of the stud. The use of an edge to edge stud finder is highly recommended.
• Hardware provided is for attachment of mount through standard thickness drywall into wood studs, or mount to solid concrete wall. Installers are responsible to provide hardware for other types of mounting situations.
• Tighten screws so that ceiling mount is firmly attached, but do not over tighten. Over tightening can damage the screws, greatly reducing their holding power.

1B Installing the Ceiling Mount (Concrete Surfaces)

For installation to wood surfaces, refer to Step 1A.

1. Hold the marking template provided against the ceiling where you want to install your projector, mark four holes for drilling using a marking pen or pencil.

2. Using an electric drill and a 5/16″ (8mm) drill bit, drill the four mounting holes to a minimum depth of 2.5″ (64mm).

3. 

WARNING

• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchors.
• Make sure that the wall will safely support four times the combined load of the equipment and all attached hardware and components.

Attach ceiling mount with four concrete anchors (G) and four screws (H) as shown in the figure on the left.
Using a socket wrench tighten each screw until the ceiling mount is firmly attached.

Do not use electric / power drill and do not over tighten the screws.

Attaching the Projector Bracket to the Projector

WARNING

• If your projector model has three mounting holes only, please remove the fourth extension bracket using the supplied Allen Key (E).
• If your projector model does not have at least three mounting holes, do not use this mount.

Loosen the M6x12mm Screws using the supplied Allen Key (E) until you can slide the extension brackets freely, as shown.
To suit the mounting hole configuration of your projector, you may need to replace the attached Extension Brackets with the additional short or long Extension Brackets (A, B, C, D) supplied in the package.

Place the Projector Bracket Assembly over the Projector and align the center the Mount with the Center of Gravity of the Projector.

• Align the shift adjustment opening (at the center of the projector bracket) in parallel with the projector lens opening to allow shift adjustments to the projector.
• Place the Bottom Spacers (R) in between the Extension Brackets and the Projector, and align the mounting holes as shown below. If you are using a short extension bracket you must use spacer Q.
• Select the correct Mounting Screws from the Hardware Package (J, K, L, M,or N) and firmly screw the Projector Bracket Assembly onto your Projector using a Philips Screwdriver. Once this is done, the Projector Bracket Assembly is ready to be mounted onto the Ceiling Mount.

 Attaching the Projector Assembly to the Ceiling Mount

Using an assistant to support the weight of the projector, attach the Projector Assembly to the Ceiling Mount as shown above. Tighten the M6x30mm screws on either side with the supplied Allen Key (E).

TIP When the projector requires servicing, remove the projector via this easy disconnection point to save time.

Adjusting the Projector (Part 1 of 2)

Adjusting the Projector (Part 2 of 2)

Maintenance

Please check that the TV wall mount is secure and safe to use at regular intervals. If you have any questions regarding any of the instructions or warnings, please contact your local distributor (OR) contact QualGear technical support via email at support@qualgear.com.

• store.qualgear.com
• google.com/+qualgear
• youtube.com/qualgear
• support@qualgear.com
• facebook.com/qualgear
• twitter.com/qualgear
• pinterest.com/qualgearusa

References

• QualGear - Projector Screens, TV / monitor / projector mounts
• QualGear速 - Professional Grade Mounts
• QualGear Warranty On Product Purchase | Qualgear Warranty

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>